Dae Heon Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dae Heon Lee has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Hosung Choo
Department of Electronic and Electrical Engineering, Hongik University, Seoul, Korea
4 shared publications - Ki Baek Kim
Electronics and Telecommunications Research Institute (ETRI), Yuseong-gu, Daejeon, Republic of Korea
3 shared publications - Dae-Yeon Kim
Electronics and Telecommunications Research Institute (ETRI), Yuseong-daero, South Korea
2 shared publications - Eunjung Kang
Department of Electronic and Electrical Engineering, Hongik University, Seoul 04066, Republic of Korea
2 shared publications - Sangwoon Youn
Department of Electronic and Electrical Engineering, Hongik University, Seoul, South Korea
2 shared publications - Tae Heung Lim
Department of Electrical Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, Korea
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 127229-127238
Real-Time 3-D Localization of Jamming Drones Using Covariance Matrix-Based Vision Transformer
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 127229-127238
Open AccessReal-Time 3-D Localization of Jamming Drones Using Covariance Matrix-Based Vision Transformer
- 21 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (3) , 869-878
Conductive Thin-Film Structure for EMP Protection of Operational Infrastructure Facilities: Measurement and Verification up to 18 GHz
Given the increasing need for an electromagnetic pulse (EMP) protection of operational infrastructure facilities, we designed, constructed, and verified a conductive thin-film structure with high shielding effectiveness (SE) from 10 kHz to 18 GHz. The SE of the conductive thin-films was measured preliminarily using ASTM D-4935 and the aperture method. In particular, the aperture size for the low-frequency magnetic band was increased to extend the dynamic range (DR) of measurement. We constructed a test shelter and an EMP protection facility for an operational office using the conductive thin-film. The measurement results for the material itself, test shelter, and the EMP protection facility were consistent from 10 kHz to 18 GHz, validating the measurement and construction methods proposed in this article. Moreover, the SE of the constructed EMP protection facility met the MIL-STD-188-125-1 requirements (over 80 dB up to 18 GHz). This study demonstrated that conductive thin-film structures can provide an alternative shielding solution for major infrastructure facilities.
- 21 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (3) , 869-878
Conductive Thin-Film Structure for EMP Protection of Operational Infrastructure Facilities: Measurement and Verification up to 18 GHz
Given the increasing need for an electromagnetic pulse (EMP) protection of operational infrastructure facilities, we designed, constructed, and verified a conductive thin-film structure with high shielding effectiveness (SE) from 10 kHz to 18 GHz. The SE of the conductive thin-films was measured preliminarily using ASTM D-4935 and the aperture method. In particular, the aperture size for the low-frequency magnetic band was increased to extend the dynamic range (DR) of measurement. We constructed a test shelter and an EMP protection facility for an operational office using the conductive thin-film. The measurement results for the material itself, test shelter, and the EMP protection facility were consistent from 10 kHz to 18 GHz, validating the measurement and construction methods proposed in this article. Moreover, the SE of the constructed EMP protection facility met the MIL-STD-188-125-1 requirements (over 80 dB up to 18 GHz). This study demonstrated that conductive thin-film structures can provide an alternative shielding solution for major infrastructure facilities.
- Open Access
- 31 December 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (12) , 1054-1061
Analysis of the Magnetic Shielding Effectiveness of Conductive Sheets according to Aperture Sizes
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 December 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (12) , 1054-1061
Open AccessAnalysis of the Magnetic Shielding Effectiveness of Conductive Sheets according to Aperture Sizes
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- Open Access
- 19 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 47048-47055
An Electrically Small Frequency Selective Loop Antenna for Shielding Effectiveness Measurement
This paper proposes an electrically small and frequency selective loop (FSL) antenna for shielding effectiveness (SE) measurement in low frequency (10 kHz – 30 MHz) magnetic fields. The proposed antenna consists of an outer loop and an inner loop. A low-pass filter is placed between outer and inner loop to improve the antenna factor (AF) in the upper frequency band as the number of loop turns increases. The size of the designed antenna is 220 mm × 220 mm, which achieves 46 % reduction of the antenna area compared to conventional 300 mm loop antennas and the proposed antenna preserves the AF characteristic over the entire frequency range (10 kHz – 30 MHz). In addition, the loop of the designed antenna is printed using microstrip techniques, which reduces the cost and complexity of the antenna fabrication. The results demonstrate that the proposed antenna is suitable for SE measurements of small enclosures (all dimensions between 0.75 m and 2 m).
- 19 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 47048-47055
Open AccessAn Electrically Small Frequency Selective Loop Antenna for Shielding Effectiveness Measurement
This paper proposes an electrically small and frequency selective loop (FSL) antenna for shielding effectiveness (SE) measurement in low frequency (10 kHz – 30 MHz) magnetic fields. The proposed antenna consists of an outer loop and an inner loop. A low-pass filter is placed between outer and inner loop to improve the antenna factor (AF) in the upper frequency band as the number of loop turns increases. The size of the designed antenna is 220 mm × 220 mm, which achieves 46 % reduction of the antenna area compared to conventional 300 mm loop antennas and the proposed antenna preserves the AF characteristic over the entire frequency range (10 kHz – 30 MHz). In addition, the loop of the designed antenna is printed using microstrip techniques, which reduces the cost and complexity of the antenna fabrication. The results demonstrate that the proposed antenna is suitable for SE measurements of small enclosures (all dimensions between 0.75 m and 2 m).
- Open Access
Design of a Miniaturized Rectangular Multiturn Loop Antenna for Shielding Effectiveness Measurement
This paper proposes a novel miniaturized rectangular loop antenna sensor consisting of a multiturn wire and a cuboid ferrite core. The lateral surface of the ferrite core is tightly wound by the multiturn wire. To verify its feasibility, the antenna sensor is fabricated, and the antenna factor (AF) levels are measured using the three-antenna method from the very low frequency (VLF) to the high-frequency (HF) bands. The measured AF levels are 31.8 dB (with a covering plastic case) and 33.1 dB (without a covering plastic case) at 30 kHz. In addition, the proposed antenna is employed in the shielding effectiveness measurement of a small commercial cabinet to observe its suitability for shielding effectiveness (SE) measurement of small shielding enclosures. The SE values averaged over the frequency range from 10 kHz to 3 MHz are 4.1 dB and 12 dB in the horizontal and vertical polarizations, respectively.
Open AccessDesign of a Miniaturized Rectangular Multiturn Loop Antenna for Shielding Effectiveness Measurement
This paper proposes a novel miniaturized rectangular loop antenna sensor consisting of a multiturn wire and a cuboid ferrite core. The lateral surface of the ferrite core is tightly wound by the multiturn wire. To verify its feasibility, the antenna sensor is fabricated, and the antenna factor (AF) levels are measured using the three-antenna method from the very low frequency (VLF) to the high-frequency (HF) bands. The measured AF levels are 31.8 dB (with a covering plastic case) and 33.1 dB (without a covering plastic case) at 30 kHz. In addition, the proposed antenna is employed in the shielding effectiveness measurement of a small commercial cabinet to observe its suitability for shielding effectiveness (SE) measurement of small shielding enclosures. The SE values averaged over the frequency range from 10 kHz to 3 MHz are 4.1 dB and 12 dB in the horizontal and vertical polarizations, respectively.
- Open Access
- 16 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 54872-54878
Design of a Miniaturized Printed Multi-Turn Loop Antenna for Shielding Effectiveness Measurement
This paper proposes a novel miniaturized loop antenna consisting of a multi-turn printed strip and a ring-shaped ferrite core. The lateral surface of the ferrite core is tightly wrapped by the circular multi-turn strip, which is printed on a thin, ring-shaped Styrofoam. To verify the feasibility, the proposed antenna is fabricated, and the antenna factor (AF) levels are measured using the three-antenna method from the VLF to HF band. The AF levels by measurement, theory, and simulation are 36.14 dB, 34.01 dB, and 33.6 dB at 30 kHz, respectively. In the VLF band, the antenna has a diameter of 114 mm, which is miniaturized to less than 60% compared to previous research. In addition, the proposed antenna is employed in the shielding effectiveness (SE) measurement of a small commercial cabinet to observe its suitability for SE measurement of small shielding enclosures. The SE values averaged over the frequency range from 10 kHz to 3 MHz are 5.19 dB and 14.14 dB in the horizontal and vertical polarizations.
- 16 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 54872-54878
Open AccessDesign of a Miniaturized Printed Multi-Turn Loop Antenna for Shielding Effectiveness Measurement
This paper proposes a novel miniaturized loop antenna consisting of a multi-turn printed strip and a ring-shaped ferrite core. The lateral surface of the ferrite core is tightly wrapped by the circular multi-turn strip, which is printed on a thin, ring-shaped Styrofoam. To verify the feasibility, the proposed antenna is fabricated, and the antenna factor (AF) levels are measured using the three-antenna method from the VLF to HF band. The AF levels by measurement, theory, and simulation are 36.14 dB, 34.01 dB, and 33.6 dB at 30 kHz, respectively. In the VLF band, the antenna has a diameter of 114 mm, which is miniaturized to less than 60% compared to previous research. In addition, the proposed antenna is employed in the shielding effectiveness (SE) measurement of a small commercial cabinet to observe its suitability for SE measurement of small shielding enclosures. The SE values averaged over the frequency range from 10 kHz to 3 MHz are 5.19 dB and 14.14 dB in the horizontal and vertical polarizations.