Vitaliy Maksymov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vitaliy Maksymov has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Dmytro Konovalov
Department of Energy and Process Engineering, Norwegian University of Science and Technology, Kolbjørn Hejes vei 1, 7034 Trondheim, Norway
4 shared publications - Halina Kobalava
Admiral Makarov National University of Shipbuilding
4 shared publications - Mykola Radchenko
Admiral Makarov National University of Shipbuilding, Heroes of Ukraine Avenue 9, 54025 Mykolaiv, Ukraine
4 shared publications - Andrii Radchenko
Admiral Makarov National University of Shipbuilding, Heroes of Ukraine Avenue 9, 54025 Mykolaiv, Ukraine
1 shared publication - Eugeniy Trushliakov
Admiral Makarov National University of Shipbuilding
1 shared publication Mykola Avdeev
Kherson Shipbuilding Company
1 shared publication
Latest Publications
- 8 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 236 (4) , 634-646
Research of characteristics of the flow part of an aerothermopressor for gas turbine intercooling air
Complex gas turbine schemes with air intercooling are usually used to bring the compression process of working fluid in compressor closer to isothermal one. A promising way to realize it is to use an aerothermopressor. The aerothermopressor is a two-phase jet apparatus, in which the highly dispersed liquid (water) is injected into the superheated gas (air) stream accelerated to the speed closed to the sound speed value (Mach number from 0.8 to 0.9). The air pressure at the aerothermopressor outlet (after diffuser) is higher than at the inlet due to instantaneous evaporation of highly dispersed liquid practically without friction losses in mixing chamber and with an increase in pressure of the mixed homogenous flow. The liquid evaporation is conducted by removing the heat from the air flow. In the course of the experimental research, the operation of the aerothermopressor for gas turbine intercooling air was simulated and its characteristics (hydraulic resistance coefficients, pressure increase, and air temperature) were determined. Within contact cooling of air in the aerothermopressor, the values of the total pressure increase in the aerothermopressor were from 1.02 to 1.04 (2–4%). Thus, the aerothermopressor use to provide contact evaporative cooling of cyclic air between the compressor stages will ensure not only compensation for pressure losses but also provides an increase in total air pressure with simultaneous cooling. Injection of liquid in a larger amount than is necessary for evaporation ensures a decrease in pressure losses in the flow path of the aerothermopressor by 15–20%. When the amount of water flow is more than 10–15%, the pressure loss becomes equal to the loss for the “dry” aerothermopressor, and with a further increase in the amount of injected liquid, they are exceeded. The values of errors in the relative increase of air pressure in the aerothermopressor measurements not exceeded 4%. The results obtained can be used in the practice of designing intercooling systems for gas turbines.
- 8 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 236 (4) , 634-646
Research of characteristics of the flow part of an aerothermopressor for gas turbine intercooling air
Complex gas turbine schemes with air intercooling are usually used to bring the compression process of working fluid in compressor closer to isothermal one. A promising way to realize it is to use an aerothermopressor. The aerothermopressor is a two-phase jet apparatus, in which the highly dispersed liquid (water) is injected into the superheated gas (air) stream accelerated to the speed closed to the sound speed value (Mach number from 0.8 to 0.9). The air pressure at the aerothermopressor outlet (after diffuser) is higher than at the inlet due to instantaneous evaporation of highly dispersed liquid practically without friction losses in mixing chamber and with an increase in pressure of the mixed homogenous flow. The liquid evaporation is conducted by removing the heat from the air flow. In the course of the experimental research, the operation of the aerothermopressor for gas turbine intercooling air was simulated and its characteristics (hydraulic resistance coefficients, pressure increase, and air temperature) were determined. Within contact cooling of air in the aerothermopressor, the values of the total pressure increase in the aerothermopressor were from 1.02 to 1.04 (2–4%). Thus, the aerothermopressor use to provide contact evaporative cooling of cyclic air between the compressor stages will ensure not only compensation for pressure losses but also provides an increase in total air pressure with simultaneous cooling. Injection of liquid in a larger amount than is necessary for evaporation ensures a decrease in pressure losses in the flow path of the aerothermopressor by 15–20%. When the amount of water flow is more than 10–15%, the pressure loss becomes equal to the loss for the “dry” aerothermopressor, and with a further increase in the amount of injected liquid, they are exceeded. The values of errors in the relative increase of air pressure in the aerothermopressor measurements not exceeded 4%. The results obtained can be used in the practice of designing intercooling systems for gas turbines.
- 19 January 2021
- Published by Springer Nature
- p. 519-530
Numerical Simulation of an Aerothermopressor with Incomplete Evaporation for Intercooling of the Gas Turbine Engine
- 19 January 2021
- Published by Springer Nature
- p. 519-530
Numerical Simulation of an Aerothermopressor with Incomplete Evaporation for Intercooling of the Gas Turbine Engine