Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mateusz Przywara has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Integrating Quality by Design and Discrete Element Method Modeling for Tablet Coating Process Development

    by Patryk Leszczak, Marek Laskowski, Mateusz Przywara

    Tablet coating is affected by tablet-bed dynamics, spray exposure, and liquid application, making robust process control challenging. This study aimed to integrate the discrete element method (DEM) with Quality by Design (QbD) to support process parameter selection and development of a tablet coating control strategy. DEM simulations evaluated the effects of drum rotational speed (15, 25, and 35 rpm) and tablet-bed loading (1250, 2000, and 2750 g) on tablet residence time in a virtual spray zone. Based on the simulations, drum speed and coating suspension mass flow rate were investigated experimentally using a three-level factorial design with nine conditions and one repeated centre point. Disintegration time, tablet mass variability, mechanical strength, and visual coating defects were evaluated. DEM showed a nonlinear effect of drum speed on the variability of tablet residence time in the spray zone, with a stronger effect than bed loading. Experimental models confirmed significant effects of both process parameters on the investigated critical quality attributes (CQAs). Favourable operating regions were identified at approximately 23–30 rpm and 8–14 g/min. Conditions around 25 rpm and 11 g/min provided a favourable overall balance of the investigated quality attributes. The integration of DEM and QbD provided complementary mechanistic and experimental information for tablet coating development. The approach supported identification of a practical operating region and a representative target condition for further development of the process control strategy.

  • Open Access

    Low-Energy Mechanochemical Dry Coating for Improving the Flowability of Sodium Naproxen

    by Mateusz Przywara, Karolina Maria Leś, Marcin Chutkowski

    Sodium naproxen is a widely used nonsteroidal anti-inflammatory drug (NSAID) known for its therapeutic efficacy but also for its poor flowability, which complicates manufacturing processes. This study aimed to improve the flow properties of sodium naproxen through a patented mechanochemical dry coating method using nanostructured silica (Aerosil® R972) as a flow modifier. The process was conducted in a modified V-type tumbler mixer under selected conditions, including a 7:1 ball-to-powder mass ratio, a 10-min mixing time, and a 10 rpm rotational speed. Flowability was evaluated using Carr’s indices, while mechanical properties were assessed via shear testing with a Jenike cell. Surface morphology was characterized by SEM. Results showed that the modified sodium naproxen samples demonstrated a substantial improvement in flow indices, a shift to an “easy-flowing” classification at higher consolidation stresses, and a marked reduction in cohesion compared to the unmodified material. SEM confirmed partial silica deposition on particle surfaces. These findings indicate that the applied method effectively improves the handling characteristics of sodium naproxen powders. The process is relatively simple, requires low energy, is potentially applicable at a larger scale, and shows potential for pharmaceutical powder processing requiring flow enhancement of cohesive active ingredients.

  • Open Access

    Analysis of adsorption equilibria and surface energetic properties of stationary phases in selected hydrophilic interaction liquid chromatography systems

    by Regina Lech-Przywara, Weronika Sofińska-Chmiel, Mateusz Przywara, Wojciech Zapała

    This study focuses on the analysis of adsorption equilibria of phenol and caffeine using two chromatographic columns employed in hydrophilic interaction liquid chromatography (HILIC): Hypersil GOLD HILIC and Shodex SILICA 5NH 4D. The aim of the study was to determine the energetic properties of...

  • Open Access

    Low-Energy Mechanochemical Dry Coating for Improving the Flowability of Sodium Naproxen

    by Mateusz Przywara, Karolina Maria Leś, Marcin Chutkowski

    Sodium naproxen is a widely used nonsteroidal anti-inflammatory drug (NSAID) known for its therapeutic efficacy but also for its poor flowability, which complicates manufacturing processes. This study aimed to improve the flow properties of sodium naproxen through a patented mechanochemical dry coating method using nanostructured silica (Aerosil® R972) as a flow modifier. The process was conducted in a modified V-type tumbler mixer under selected conditions, including a 7:1 ball-to-powder mass ratio, 10-minute mixing time, and 10 rpm rotational speed. Flowability was evaluated using Carr’s indices, while mechanical properties were assessed via shear testing with a Jenike cell. Surface morphology was characterized by SEM. Results showed that the modified sodium naproxen samples demonstrated a substantial improvement in flow indices, a shift to “easy-flowing” classification at higher consolidation stresses, and a marked reduction in cohesion compared to the unmodified material. SEM confirmed uniform silica deposition on particle surfaces. These findings indicate that the applied method effectively improves the handling characteristics of sodium naproxen powders. The process is simple, scalable, and suitable for pharmaceutical applications requiring flow enhancement in cohesive active ingredients.

  • Open Access

    Influence of Powder Mixing and Manufacturing Process on the Quality Attributes of Sodium Naproxen Tablets

    by Mateusz Przywara

    Powder mixing is a critical step in pharmaceutical manufacturing, as the uniform distribution of an active pharmaceutical ingredient (API) affects the quality of the final dosage form. This study investigated the relationship between powder mixing performance and tablet quality attributes using sodium naproxen as a model API with limited flowability. Powder mixtures were prepared in a V-type blender, and the mixing index evolution was evaluated at different rotational speeds. Tablets were subsequently produced either by direct compression or by pan granulation followed by compression, and their critical quality attributes, including tablet mass, thickness, crushing strength, abrasiveness, and API content variability, were evaluated. The mixing index rapidly increased during blending and reached high values for all investigated conditions; however, similar mixing efficiency did not result in equivalent tablet properties. Directly compressed tablets exhibited higher crushing strength, lower abrasiveness, and lower API content variability compared with tablets obtained after pan granulation. The results demonstrated that the powder processing route had a stronger influence on final tablet performance than differences in mixing speed within the investigated range. The combination of mixing index evaluation with tablet quality assessment provides a comprehensive approach for understanding the influence of powder processing conditions on pharmaceutical tablet performance. Two-way ANOVA demonstrated that manufacturing technology exerted a substantially stronger influence on tablet quality attributes than mixing speed.

  • Open Access

    Influence of Powder Mixing Efficiency on the Quality Attributes of Pharmaceutical Tablets

    by Mateusz Przywara

    Powder mixing is a critical step in pharmaceutical manufacturing, as the uniform distribution of an active pharmaceutical ingredient (API) affects the quality of the final dosage form. This study investigated the relationship between powder mixing performance and tablet quality attributes using sodium naproxen as a model API with limited flowability. Powder mixtures were prepared in a V-type blender, and the mixing index evolution was evaluated at different rotational speeds. Tablets were subsequently produced either by direct compression or by pan granulation followed by compression, and their critical quality attributes, including tablet mass, thickness, crushing strength, abrasiveness, and API content variability, were evaluated. The mixing index rapidly increased during blending and reached high values for all investigated conditions; however, similar mixing efficiency did not result in equivalent tablet properties. Directly compressed tablets exhibited higher crushing strength, lower abrasiveness, and lower API content variability compared with tablets obtained after pan granulation. The results demonstrated that the powder processing route had a stronger influence on final tablet performance than differences in mixing speed within the investigated range. The combination of mixing index evaluation with tablet quality assessment provides a comprehensive approach for understanding the influence of powder processing conditions on pharmaceutical tablet performance.

  • Open Access

    Quality by Design Approach to the Optimization of Cohesive Powder Blending in Direct Compression

    by Mateusz Przywara, Patryk Leszczak

    Background/Objectives: Direct compression of cohesive powders is often challenged by poor flow, blend heterogeneity, and variable tablet quality. This study investigated how mixing time, fill level, and rotational speed affect the blending behavior and tablet properties of a sodium naproxen–calcium carbonate formulation and aimed to define a robust operating space for process optimization. Methods: Powder blends were prepared in a V-type mixer according to a central composite design and analyzed using response surface methodology. The effects of the three process parameters were evaluated through powder flow descriptors (angle of repose, angle of fall, and angle of difference) and tablet quality attributes, including thickness, mass, active pharmaceutical ingredient (API) content, and abrasiveness. Statistical significance was assessed by ANOVA, and a design space was established using predefined acceptance criteria. Results: Mixing time significantly affected the angle of difference, indicating changes in blend cohesiveness and flow uniformity, whereas fill level significantly influenced API content. Tablet thickness and mass remained relatively stable across the tested conditions. Abrasiveness showed the greatest numerical variability and tended to increase at high fill levels combined with short mixing times. Response surface analysis identified two acceptable operational regions that satisfied the quality criteria for blend homogeneity, API content, and abrasiveness. Conclusions: The studied process variables exerted selective, property-specific effects rather than uniform changes across all quality attributes. The results support QbD-based process design for cohesive direct-compression systems and show that robust tablet manufacture can be achieved within more than one operating window.


  • Open Access

    Quality by Design Approach to the Optimization of Cohesive Powder Blending in Direct Compression

    by Mateusz Przywara, Patryk Leszczak

    Direct compression is a widely used manufacturing method for solid oral dosage forms; however, its performance strongly depends on powder flowability, cohesiveness, and compactability, particularly in systems containing fine cohesive particles. This study investigated the influence of mixing time, fill level, and rotational speed on the properties of sodium naproxen–calcium carbonate blends and the resulting tablets prepared by direct compression. Powder blends were produced in a V-type mixer according to a central composite design, and the effects of process variables were evaluated using response surface methodology and analysis of variance. Blend properties were characterized by the angle of repose, angle of fall, and angle of difference, whereas tablet quality was assessed in terms of thickness, mass, active pharmaceutical ingredient content, and abrasiveness. Mixing time significantly affected the angle of difference, indicating changes in blend cohesiveness and flow uniformity, while fill level was identified as the main factor influencing active pharmaceutical ingredient content uniformity. Response surface analysis enabled identification of operating regions satisfying predefined criteria for blend homogeneity, active pharmaceutical ingredient content, and abrasiveness. The results provide guidance for optimization of direct compression processes involving cohesive pharmaceutical powders and support the application of Quality by Design principles in tablet manufacturing.


  • Technology Transfer in the Pharmaceutical Industry within Regulatory Frameworks, Strategies and Implementation Practice

    by Aneta Raś, Mateusz Przywara, Wojciech Zapała

    Technology transfer (TT) in the pharmaceutical industry is a structured, lifecycle-oriented process that ensures the reproducible transition of products and processes from development to routine manufacturing. It should be understood not as a single event or documentation handover, but as an integrated system of knowledge transfer, process understanding, and organizational alignment within a good manufacturing practice GMP-regulated environment. This article provides a practical interpretation of TT based on key regulatory frameworks, including World health organization (WHO), European Medicines Agency (EMA), International Council for Harmonisation (ICH) Q8–Q12, Food and Drug Administration (FDA) guidance, and PIC/S requirements. The study is based on analysis of regulatory documents, scientific literature, and industrial practice, supported by experience from GMP manufacturing environments. The objective is to translate regulatory expectations into operational principles that determine TT success. The results show that effective TT depends on robust process knowledge, interdisciplinary collaboration, and consistent application of Quality by Design (QbD) and Quality Risk Management (QRM). Critical success factors include clear definition of critical process parameters (CPP) and critical quality attributes (CQA), effective analytical method transfer, and strong data integrity across sending and receiving units. Common failure modes include insufficient understanding of equipment differences, incomplete transfer of tacit knowledge, and inadequate control of material variability. Analytical transfer and scale-up are identified as particularly sensitive stages requiring strict operational control. TT is a strategic function within pharmaceutical quality systems that directly impacts product quality, regulatory compliance, and manufacturing robustness, while enabling efficient lifecycle management and reducing post-approval risks.

  • Open Access

    Structural and surface characterization of adsorbents applied in liquid chromatography

    by Regina Lech-Przywara, Tomasz Galek, Mateusz Przywara, Lidia Zapała, Wojciech Zapała

    A detailed analysis of the four commercial stationary phases often applied in liquid chromatography was performed using the following: SEM-EDS techniques and specific surface area and porosity analysis methods (multipoint BET, BJH, DH and DFT). The SEM-EDS results confirmed that the main...