Andrii Veryha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andrii Veryha has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Ruslan Politanskyi
Yuriy Fedkovych Chernivtsi National University
3 shared publications Halyna Lastivka
Yuriy Fedkovych Chernivtsi National University
2 shared publications- Ihor Helzhynskyy
Lviv Polytechnic National University
1 shared publication - Ihor Klapashchuk
Yuriy Fedkovych Chernivtsi National University
1 shared publication - Khrystyna Ivaniuk
Lviv Polytechnic National University
1 shared publication - Marharyta Rozhdestvenska
Yuriy Fedkovych Chernivtsi National University
1 shared publication
Latest Publications
- Open Access
- 30 December 2024
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- Vol. 2 (2) , 02005
Analysis of Amateur Radio Frequency Code Modulation Protocols for Transmitting Short Messages
The article is dedicated to analyzing common short message transmission protocols in digital code used by radio amateurs in amateur radio communication. The following protocols are considered: RTTY, AMTOR, PACTOR1, ISCAT, JT4, JT9, JT65, FT4, and FT8. All of them use frequency shift keying (FSK), which provides significantly better noise resistance since information is encoded in frequency changes rather than amplitude. Because of this, FM is widely used in broadcasting. The primary purpose of the listed protocols is to prevent signal fading due to radio wave reflection from the ionospheric layer (sporadic propagation), where reflection windows can be short. Therefore, modulation must be fast, and data transmission reliability must be high to ensure successful radio exchange. The article analyzes the main characteristics of these protocols, including the maximum signal-to-noise ratio (SNR) at which digital data reception and decoding are possible, transmission speed, and the bandwidth occupied by the signal. Additionally, related characteristics are examined, such as the bit transmission time and the use of error-correcting codes for noise immunity. The main FSK modulation modes are reviewed, comparing their advantages and disadvantages. It has been established that the JT4, JT9, JT65, QRA4, WSPR, FT4, and FT8 protocols provide a SNR greater than -20 dB compared to RTTY, AMTOR, PACTOR, and ISCAT. In such protocols, the signal occupies a narrower bandwidth. All the discussed protocols ensure a higher message transmission speed compared to other modulation modes. The conclusion is made that frequency modulation, combined with the use of error correction codes, significantly improves the SNR. The application of similar signal detection and decoding methods could enable the development of a decoder with substantially higher sensitivity. The development of a new type of signal for digital information transmission can be based on modifications of the JT4, JT9, JT65, QRA4, WSPR, FT4, and FT8 protocols.
- 30 December 2024
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- Vol. 2 (2) , 02005
Open AccessAnalysis of Amateur Radio Frequency Code Modulation Protocols for Transmitting Short Messages
The article is dedicated to analyzing common short message transmission protocols in digital code used by radio amateurs in amateur radio communication. The following protocols are considered: RTTY, AMTOR, PACTOR1, ISCAT, JT4, JT9, JT65, FT4, and FT8. All of them use frequency shift keying (FSK), which provides significantly better noise resistance since information is encoded in frequency changes rather than amplitude. Because of this, FM is widely used in broadcasting. The primary purpose of the listed protocols is to prevent signal fading due to radio wave reflection from the ionospheric layer (sporadic propagation), where reflection windows can be short. Therefore, modulation must be fast, and data transmission reliability must be high to ensure successful radio exchange. The article analyzes the main characteristics of these protocols, including the maximum signal-to-noise ratio (SNR) at which digital data reception and decoding are possible, transmission speed, and the bandwidth occupied by the signal. Additionally, related characteristics are examined, such as the bit transmission time and the use of error-correcting codes for noise immunity. The main FSK modulation modes are reviewed, comparing their advantages and disadvantages. It has been established that the JT4, JT9, JT65, QRA4, WSPR, FT4, and FT8 protocols provide a SNR greater than -20 dB compared to RTTY, AMTOR, PACTOR, and ISCAT. In such protocols, the signal occupies a narrower bandwidth. All the discussed protocols ensure a higher message transmission speed compared to other modulation modes. The conclusion is made that frequency modulation, combined with the use of error correction codes, significantly improves the SNR. The application of similar signal detection and decoding methods could enable the development of a decoder with substantially higher sensitivity. The development of a new type of signal for digital information transmission can be based on modifications of the JT4, JT9, JT65, QRA4, WSPR, FT4, and FT8 protocols.
- Open Access
- 30 June 2023
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- No. 1,p. 01012
Using PIC18 Microcontrollers to Generate Chaotic Signals Based on Logistic Mapping
In this paper, simulation and hardware implementation of the device for generating chaotic signals based on logistic mapping using microcontrollers of the РІС18 series was carried out. The operation of the device was investigated in the mode of generating chaotic oscillations at different values of the control parameter λ. By certain hardware and software modification, this generator can be used as a voice signal encryption The results of simulation and experimental studies confirm the possibility of using PIC18 microcontrollers for the implementation of chaotic oscillation generators based on discrete mappings, as well as using these controllers in the hardware implementation of language information encryption devices.
- 30 June 2023
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- No. 1,p. 01012
Open AccessUsing PIC18 Microcontrollers to Generate Chaotic Signals Based on Logistic Mapping
In this paper, simulation and hardware implementation of the device for generating chaotic signals based on logistic mapping using microcontrollers of the РІС18 series was carried out. The operation of the device was investigated in the mode of generating chaotic oscillations at different values of the control parameter λ. By certain hardware and software modification, this generator can be used as a voice signal encryption The results of simulation and experimental studies confirm the possibility of using PIC18 microcontrollers for the implementation of chaotic oscillation generators based on discrete mappings, as well as using these controllers in the hardware implementation of language information encryption devices.
- Open Access
- 30 June 2023
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- No. 1,p. 01003
Analysis of Self-Similar Binary Sequences
Rectangular pulses are simple to form, including with the help of a modern radio element base. In the work, a calculation analysis of the base and correlation coefficient of a binary sequence with a length of eight rectangular pulses was carried out. The obtained calculations of the base of sequences were analyzed, and a conclusion was made about which of them is the most suitable for encoding information during data transmission over the radio channel. Based on the calculations of the correlation coefficient between the series of pulse sequences, it was concluded which of them could be separated in the channel. Based on the structure of the self-similar sequence of pulses, a mathematical model and an expression of the spectral density of the proposed signal are written. A new method of correlation analysis for sequences that are symmetrical was also proposed, which allowed for improved recognition of the useful signal at lower signal-to-noise ratios in the communication channel. The method is a combination of autocorrelation and cross-correlation functions. The right and left halves of the symmetrical sequence and the reference signal are compared. The ratio of the height of the main petal to the side petals in our proposed correlation function is greater than in the classical version. To obtain the greatest possible ratio of the height of the petals, it is advisable to choose symmetrical sequences that have the largest base. With the help of such sequences, it is planned to encode one bit of information, which should improve the recognition of transmitted information against the background of noise. The obtained results are planned to be used for the development of a transmitter and receiver with an improved coding method for recognizing a useful signal against a background of noise.
- 30 June 2023
- Published by Yuriy Fedkovych Chernivtsi National University in Security of Infocommunication Systems and Internet of Things
- No. 1,p. 01003
Open AccessAnalysis of Self-Similar Binary Sequences
Rectangular pulses are simple to form, including with the help of a modern radio element base. In the work, a calculation analysis of the base and correlation coefficient of a binary sequence with a length of eight rectangular pulses was carried out. The obtained calculations of the base of sequences were analyzed, and a conclusion was made about which of them is the most suitable for encoding information during data transmission over the radio channel. Based on the calculations of the correlation coefficient between the series of pulse sequences, it was concluded which of them could be separated in the channel. Based on the structure of the self-similar sequence of pulses, a mathematical model and an expression of the spectral density of the proposed signal are written. A new method of correlation analysis for sequences that are symmetrical was also proposed, which allowed for improved recognition of the useful signal at lower signal-to-noise ratios in the communication channel. The method is a combination of autocorrelation and cross-correlation functions. The right and left halves of the symmetrical sequence and the reference signal are compared. The ratio of the height of the main petal to the side petals in our proposed correlation function is greater than in the classical version. To obtain the greatest possible ratio of the height of the petals, it is advisable to choose symmetrical sequences that have the largest base. With the help of such sequences, it is planned to encode one bit of information, which should improve the recognition of transmitted information against the background of noise. The obtained results are planned to be used for the development of a transmitter and receiver with an improved coding method for recognizing a useful signal against a background of noise.
- Open Access
- 26 February 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (1(57)) , 30-33
Development of portable device for measurement of dynamic and static light-emission WOLED characteristics
The research object of this work is the parameters of organic light-emitting diodes, namely power and luminous flux. Determination of these parameters can be carried out using a photodiode and requires measuring the dark current of the sensor (photodiode), measuring the current of the photodiode when illuminated by the LED under investigation. And also take into account the relationship between the light flux received by the sensor and its output current, and take into account the spectral characteristics of the sensor. Calculate the investigated parameters of the LED based on the measurements. Carrying out these measurements requires laboratory instruments and workplace organization, and further calculations are routine work. It is possible to increase the measurement accuracy by improving the existing methods for measuring the required parameters, and it is possible to automate the process of measurements and calculations using a modern microprocessor radioelement base. Microcontrollers are widespread such radioelements. They have the necessary peripherals for independent operation and have sufficient computing power to implement the required measuring device. Its application makes it possible to automate the measurement process, carry out the necessary calculations, save correction constants, accumulate and process the obtained data, analyze these received data, exchange data with a computer, etc. So, the work is aimed at developing a methodology that will allow the simultaneous measurement of power and luminous flux of planar light sources. And also on the feasibility of this technique in the device and software with the ability to measure the power of the light source in an arbitrary band of the spectral visible range. Thus, it is possible to determine what power in watts a light source emits with the dynamics of supply currents in the optical bands, knowing the spectrum of this source without using glass filters. So, the result of applying the technique is to determine the power of light radiation (in watts) or the luminous flux (in lumens) of the emitter (light sources).
- 26 February 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (1(57)) , 30-33
Open AccessDevelopment of portable device for measurement of dynamic and static light-emission WOLED characteristics
The research object of this work is the parameters of organic light-emitting diodes, namely power and luminous flux. Determination of these parameters can be carried out using a photodiode and requires measuring the dark current of the sensor (photodiode), measuring the current of the photodiode when illuminated by the LED under investigation. And also take into account the relationship between the light flux received by the sensor and its output current, and take into account the spectral characteristics of the sensor. Calculate the investigated parameters of the LED based on the measurements. Carrying out these measurements requires laboratory instruments and workplace organization, and further calculations are routine work. It is possible to increase the measurement accuracy by improving the existing methods for measuring the required parameters, and it is possible to automate the process of measurements and calculations using a modern microprocessor radioelement base. Microcontrollers are widespread such radioelements. They have the necessary peripherals for independent operation and have sufficient computing power to implement the required measuring device. Its application makes it possible to automate the measurement process, carry out the necessary calculations, save correction constants, accumulate and process the obtained data, analyze these received data, exchange data with a computer, etc. So, the work is aimed at developing a methodology that will allow the simultaneous measurement of power and luminous flux of planar light sources. And also on the feasibility of this technique in the device and software with the ability to measure the power of the light source in an arbitrary band of the spectral visible range. Thus, it is possible to determine what power in watts a light source emits with the dynamics of supply currents in the optical bands, knowing the spectrum of this source without using glass filters. So, the result of applying the technique is to determine the power of light radiation (in watts) or the luminous flux (in lumens) of the emitter (light sources).
- Open Access
- 30 March 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (1) , 62-65
MODELLING OF SPINTRONIC DEVICES FOR APPLICATION IN RANDOM ACCESS MEMORY
The article analyzes the physical processes that occur in spin-valve structures during recording process which occurs in high-speed magnetic memory devices. Considered are devices using magnetization of the ferromagnetic layer through transmitting magnetic moment by polarized spin (STT-MRAM). Basic equations are derived to model the information recording process in the model of symmetric binary channel. Because the error probability arises from the magnetization process, a model of the magnetization process is formed, which is derived from the Landau-Lifshitz-Gilbert equations under the assumption of a single-domain magnet. The choice of a single-domain model is due to the nanometer size of the flat magnetic layer. The developed method of modeling the recording process determines the dependence of such characteristics as the bit error probability and the rate of recording on two important technological characteristics of the recording process: the value of the current and its duration. The end result and the aim of the simulation is to determine the optimal values of the current and its duration at which the speed of the recording process is the highest for a given level of error probability. The numerical values of the transmission rate and error probability were obtained for a wide range of current values (10–1500 μA) and recording time of one bit (1–70 ns), and generally correctly describe the process of information transmission. The calculated data were compared with the technical characteristics of existing industrial devices and devices which are the object of the scientific research. The resulting model can be used to simulate devices using different values of recording currents: STT-MRAM series chips using low current values (500-100 μA), devices in the stage of technological design and using medium current values (100–500 μA) and devices that are the object of experimental scientific research and use high currents (500–1000 μA). The model can also be applied to simulate devices with different data rates, which have different requirements for both transmission speed and bit error probability. In this way, the model can be applied to both high-speed memory devices in computer systems and signal sensors, which are connected to sensor networks or connected to the IoT.
- 30 March 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (1) , 62-65
Open AccessMODELLING OF SPINTRONIC DEVICES FOR APPLICATION IN RANDOM ACCESS MEMORY
The article analyzes the physical processes that occur in spin-valve structures during recording process which occurs in high-speed magnetic memory devices. Considered are devices using magnetization of the ferromagnetic layer through transmitting magnetic moment by polarized spin (STT-MRAM). Basic equations are derived to model the information recording process in the model of symmetric binary channel. Because the error probability arises from the magnetization process, a model of the magnetization process is formed, which is derived from the Landau-Lifshitz-Gilbert equations under the assumption of a single-domain magnet. The choice of a single-domain model is due to the nanometer size of the flat magnetic layer. The developed method of modeling the recording process determines the dependence of such characteristics as the bit error probability and the rate of recording on two important technological characteristics of the recording process: the value of the current and its duration. The end result and the aim of the simulation is to determine the optimal values of the current and its duration at which the speed of the recording process is the highest for a given level of error probability. The numerical values of the transmission rate and error probability were obtained for a wide range of current values (10–1500 μA) and recording time of one bit (1–70 ns), and generally correctly describe the process of information transmission. The calculated data were compared with the technical characteristics of existing industrial devices and devices which are the object of the scientific research. The resulting model can be used to simulate devices using different values of recording currents: STT-MRAM series chips using low current values (500-100 μA), devices in the stage of technological design and using medium current values (100–500 μA) and devices that are the object of experimental scientific research and use high currents (500–1000 μA). The model can also be applied to simulate devices with different data rates, which have different requirements for both transmission speed and bit error probability. In this way, the model can be applied to both high-speed memory devices in computer systems and signal sensors, which are connected to sensor networks or connected to the IoT.
- Open Access
- 30 March 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (1) , 12-15
TIME INTERVAL SWITCHING DEVICE
The proposed electronic switching device, which is a replacement (analogue) of the electromechanical switch KEP-12. The status and time settings are set for each channel separately through the device menu. It is characterized by less time and ease of reconfiguration.
- 30 March 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (1) , 12-15
Open AccessTIME INTERVAL SWITCHING DEVICE
The proposed electronic switching device, which is a replacement (analogue) of the electromechanical switch KEP-12. The status and time settings are set for each channel separately through the device menu. It is characterized by less time and ease of reconfiguration.