June-Woo Juhn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
June-Woo Juhn has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
- Sang-Kyeun Kim
Princeton Plasma Physics Laboratory
6 shared publications - Ricardo Shousha
Princeton Plasma Physics Laboratory 2 , Princeton, New Jersey 08540
5 shared publications - Sang-Hee Hahn
Korea Institute of Fusion Energy , Daejeon 34133
5 shared publications - Hyunsun Han
Korea Institute of Fusion Energy
4 shared publications - Seong-Moo Yang
Princeton Plasma Physics Laboratory
4 shared publications - Yong Un Nam
Korea Institute of Fusion Energy
4 shared publications
Latest Publications
- Open Access
- 7 October 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126043
Revised error field assessment in KSTAR with profile diagnostics of resonant field penetration
The assessment of the n = 1 intrinsic error field in KSTAR has been revised in three respects. First, a local penetration timing criterion is defined from electron cyclotron emission (ECE) and charge exchange spectroscopy (CES) signatures near the reconstructed q = 2 surface. This timing determines the in-vessel control coil current used as the penetration threshold in the compass scan analysis. Second, the compass scans with the MID and OFFMID coils in 1.8 T L-mode plasmas indicate an intrinsic EF level up to an order of magnitude larger than the 2015 KSTAR reference value, implying that the intrinsic EF can change over extended operation and following hardware modifications. Third, the inferred EF direction is assessed by comparing the MID and OFFMID results in terms of the General Perturbed Equilibrium Code overlap field, where the two configurations give nearly the same direction despite their different poloidal spectra. A rotating resonant magnetic perturbation (RMP) experiment provides an additional dynamic check of this direction, with penetration observed near the phase predicted from the static MID scan. The reversed- B t comparison further constrains the possible source symmetry and is more compatible with a PF related contribution than with a TF dominated contribution, although the specific hardware source is not identified. These results provide an updated EF reference for KSTAR operation and motivate periodic reassessment of the intrinsic EF over the operational lifetime of the device.
- 7 October 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126043
Open AccessRevised error field assessment in KSTAR with profile diagnostics of resonant field penetration
The assessment of the n = 1 intrinsic error field in KSTAR has been revised in three respects. First, a local penetration timing criterion is defined from electron cyclotron emission (ECE) and charge exchange spectroscopy (CES) signatures near the reconstructed q = 2 surface. This timing determines the in-vessel control coil current used as the penetration threshold in the compass scan analysis. Second, the compass scans with the MID and OFFMID coils in 1.8 T L-mode plasmas indicate an intrinsic EF level up to an order of magnitude larger than the 2015 KSTAR reference value, implying that the intrinsic EF can change over extended operation and following hardware modifications. Third, the inferred EF direction is assessed by comparing the MID and OFFMID results in terms of the General Perturbed Equilibrium Code overlap field, where the two configurations give nearly the same direction despite their different poloidal spectra. A rotating resonant magnetic perturbation (RMP) experiment provides an additional dynamic check of this direction, with penetration observed near the phase predicted from the static MID scan. The reversed- B t comparison further constrains the possible source symmetry and is more compatible with a PF related contribution than with a TF dominated contribution, although the specific hardware source is not identified. These results provide an updated EF reference for KSTAR operation and motivate periodic reassessment of the intrinsic EF over the operational lifetime of the device.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (10) , 5487-5491
An FPGA-Based, Full-Digital Phase Comparator of a Multi-chord Interferometer for Real-Time Density Control in KSTAR
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (10) , 5487-5491
An FPGA-Based, Full-Digital Phase Comparator of a Multi-chord Interferometer for Real-Time Density Control in KSTAR
- Open Access
- 31 July 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (8) , 085001
Experimental demonstration of reactor-relevant adaptive density control on the DIII-D tokamak with coordinated gas and pellet fueling
Precise regulation of plasma density is crucial for achieving and maintaining fusion-relevant conditions in reactor-grade tokamaks. Tokamak reactors will utilize both gas puffing and pellet injection as standard fueling mechanisms. However, the coordinated use of gas puffing and pellet injection within feedback control frameworks is largely unexplored, underscoring the necessity to develop and validate dedicated strategies on existing machines. These strategies must address the various challenges associated with both actuators, including actuation delays, unknown fueling efficiencies, and the coexistence of continuous-time and discrete-time dynamics. To overcome these challenges, which surpass the capabilities of traditional empirically tuned proportional-integral-derivative (PID) control, an indirect adaptive control algorithm is proposed in this work for the regulation of the line-averaged electron density through coordinated gas puffing and pellet injection. After initial validation in simulations with a multi-reservoir global particle model, the controller was successfully implemented and tested on the DIII-D tokamak. Experimental results demonstrate robust density tracking under reactor-relevant scenarios, showcasing the controller’s ability to seamlessly coordinate actuators while handling disturbances and evolving actuator constraints. This work provides a critical step forward in the control of future fusion reactors.
- 31 July 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (8) , 085001
Open AccessExperimental demonstration of reactor-relevant adaptive density control on the DIII-D tokamak with coordinated gas and pellet fueling
Precise regulation of plasma density is crucial for achieving and maintaining fusion-relevant conditions in reactor-grade tokamaks. Tokamak reactors will utilize both gas puffing and pellet injection as standard fueling mechanisms. However, the coordinated use of gas puffing and pellet injection within feedback control frameworks is largely unexplored, underscoring the necessity to develop and validate dedicated strategies on existing machines. These strategies must address the various challenges associated with both actuators, including actuation delays, unknown fueling efficiencies, and the coexistence of continuous-time and discrete-time dynamics. To overcome these challenges, which surpass the capabilities of traditional empirically tuned proportional-integral-derivative (PID) control, an indirect adaptive control algorithm is proposed in this work for the regulation of the line-averaged electron density through coordinated gas puffing and pellet injection. After initial validation in simulations with a multi-reservoir global particle model, the controller was successfully implemented and tested on the DIII-D tokamak. Experimental results demonstrate robust density tracking under reactor-relevant scenarios, showcasing the controller’s ability to seamlessly coordinate actuators while handling disturbances and evolving actuator constraints. This work provides a critical step forward in the control of future fusion reactors.
- Open Access
- 19 May 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (7)
Radiative divertor detachment and impurity transport with nitrogen and neon seeding in KSTAR H-mode plasmas
Achieving core-edge compatible divertor detachment is a critical requirement for stable operation in future fusion devices. This study compares nitrogen and neon seeding in KSTAR H-mode plasmas with carbon walls, combining experiments and SOLPS-ITER modelling to evaluate their radiative dissipation and core-edge compatibility. Experimentally, N seeding achieved stronger divertor detachment, with larger reductions in target particle and heat fluxes, a higher divertor radiation fraction, and a lower core radiation fraction than Ne. In contrast, Ne seeding triggered a significant rise in core radiation followed by H-L back transitions, limiting the maximum total radiated power fraction to roughly half that of N. SOLPS-ITER simulations reproduced the experimental trends and revealed that the better core-edge compatibility of N arises from its higher divertor retention in addition to its higher cooling factor. The relative positions of the stagnation points of impurity poloidal velocity and ionization sources did not explain the different divertor compression. Instead, in the present modelling, the higher impurity parallel particle flux, resulting from the higher parallel impurity velocity, explains the stronger nitrogen impurity compression in the divertor region. The parallel temperature distribution with N was more favourable for achieving higher impurity parallel velocity than with Ne, because the impurity velocity is governed by modifications of the main ion flow due to friction and thermal forces, both of which strongly depend on the temperature. Ultimately, this behaviour is attributed to the strongly divertor-localized radiation of N. These results demonstrate that N is more effective than Ne in achieving radiative divertor detachment while maintaining low core contamination in KSTAR, consistent with observations in other present tokamaks.
- 19 May 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (7)
Open AccessRadiative divertor detachment and impurity transport with nitrogen and neon seeding in KSTAR H-mode plasmas
Achieving core-edge compatible divertor detachment is a critical requirement for stable operation in future fusion devices. This study compares nitrogen and neon seeding in KSTAR H-mode plasmas with carbon walls, combining experiments and SOLPS-ITER modelling to evaluate their radiative dissipation and core-edge compatibility. Experimentally, N seeding achieved stronger divertor detachment, with larger reductions in target particle and heat fluxes, a higher divertor radiation fraction, and a lower core radiation fraction than Ne. In contrast, Ne seeding triggered a significant rise in core radiation followed by H-L back transitions, limiting the maximum total radiated power fraction to roughly half that of N. SOLPS-ITER simulations reproduced the experimental trends and revealed that the better core-edge compatibility of N arises from its higher divertor retention in addition to its higher cooling factor. The relative positions of the stagnation points of impurity poloidal velocity and ionization sources did not explain the different divertor compression. Instead, in the present modelling, the higher impurity parallel particle flux, resulting from the higher parallel impurity velocity, explains the stronger nitrogen impurity compression in the divertor region. The parallel temperature distribution with N was more favourable for achieving higher impurity parallel velocity than with Ne, because the impurity velocity is governed by modifications of the main ion flow due to friction and thermal forces, both of which strongly depend on the temperature. Ultimately, this behaviour is attributed to the strongly divertor-localized radiation of N. These results demonstrate that N is more effective than Ne in achieving radiative divertor detachment while maintaining low core contamination in KSTAR, consistent with observations in other present tokamaks.
- Open Access
- 1 January 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (1) , 015007
Real-time reconstruction and control of pedestal-top electron density using RMP and gas puff at KSTAR
We report the experimental results of controlling the pedestal-top electron density by applying resonant magnetic perturbation (RMP) with in-vessel control coils and the main gas puff in the 2024-2025 KSTAR experimental campaign. The density is reconstructed using a parameterized ψ N grid and five channels of line-averaged density measured by the two-colored interferometer (TCI). The reconstruction procedure is accelerated by deploying a multi-layer perceptron to run in approximately 120 µ s and is sufficiently fast for real-time control. A proportional-integral controller was adopted, with the controller gains estimated from the system identification procedure. The experimental results demonstrate that the developed controller can follow a dynamic target while exclusively using both actuators. The absolute percentage errors between the electron density at ψ N = 0.89 and the target were approximately 1.5% median and a 2.5% average, respectively. The developed controller can even lower the density by using the pump-out mechanism under RMP, and it can follow a more dynamic range of density targets than a single actuator controller. The developed controller will enable experimental scenario exploration within a shot by dynamically setting the density target or maintaining a constant electron density within a discharge.
- 1 January 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (1) , 015007
Open AccessReal-time reconstruction and control of pedestal-top electron density using RMP and gas puff at KSTAR
We report the experimental results of controlling the pedestal-top electron density by applying resonant magnetic perturbation (RMP) with in-vessel control coils and the main gas puff in the 2024-2025 KSTAR experimental campaign. The density is reconstructed using a parameterized ψ N grid and five channels of line-averaged density measured by the two-colored interferometer (TCI). The reconstruction procedure is accelerated by deploying a multi-layer perceptron to run in approximately 120 µ s and is sufficiently fast for real-time control. A proportional-integral controller was adopted, with the controller gains estimated from the system identification procedure. The experimental results demonstrate that the developed controller can follow a dynamic target while exclusively using both actuators. The absolute percentage errors between the electron density at ψ N = 0.89 and the target were approximately 1.5% median and a 2.5% average, respectively. The developed controller can even lower the density by using the pump-out mechanism under RMP, and it can follow a more dynamic range of density targets than a single actuator controller. The developed controller will enable experimental scenario exploration within a shot by dynamically setting the density target or maintaining a constant electron density within a discharge.
- Open Access
- 2 July 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (7) , 079501
Corrigendum: TorbeamNN: machine learning-based steering of ECH mirrors on KSTAR (2025 Plasma Phys. Control. Fusion 67 055036)
- 2 July 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (7) , 079501
Open AccessCorrigendum: TorbeamNN: machine learning-based steering of ECH mirrors on KSTAR (2025 Plasma Phys. Control. Fusion 67 055036)
- Open Access
- 31 May 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (5) , 055036
TorbeamNN: machine learning-based steering of ECH mirrors on KSTAR
We have developed TorbeamNN: a machine learning surrogate model for the TORBEAM ray tracing code to predict electron cyclotron heating (ECH) and current drive locations in tokamak plasmas. TorbeamNN provides more than a 100 times speed-up compared to the highly optimized and simplified real-time implementation of TORBEAM without any reduction in accuracy compared to the offline, full fidelity TORBEAM code. The model was trained using KSTAR ECH mirror geometries and works for both O-mode and X-mode absorption. The TorbeamNN predictions have been validated both offline and real-time in experiment. TorbeamNN has been utilized to track an ECH absorption vertical position target in dynamic KSTAR plasmas as well as under varying toroidal mirror angles and with a minimal average tracking error of 0.5 cm.
- 31 May 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (5) , 055036
Open AccessTorbeamNN: machine learning-based steering of ECH mirrors on KSTAR
We have developed TorbeamNN: a machine learning surrogate model for the TORBEAM ray tracing code to predict electron cyclotron heating (ECH) and current drive locations in tokamak plasmas. TorbeamNN provides more than a 100 times speed-up compared to the highly optimized and simplified real-time implementation of TORBEAM without any reduction in accuracy compared to the offline, full fidelity TORBEAM code. The model was trained using KSTAR ECH mirror geometries and works for both O-mode and X-mode absorption. The TorbeamNN predictions have been validated both offline and real-time in experiment. TorbeamNN has been utilized to track an ECH absorption vertical position target in dynamic KSTAR plasmas as well as under varying toroidal mirror angles and with a minimal average tracking error of 0.5 cm.
- 1 April 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (4)
Development of a multi-channel mm-wave interferometer for the versatile experiment spherical torus (VEST)
The 94 GHz single-channel interferometer at the versatile experiment spherical torus has been upgraded into a multi-channel heterodyne interferometer for electron density profile measurements. Five Gaussian beam chords generated by a pair of Powell lenses and collimating lenses are vertically spaced at 75 mm intervals from the midplane to the lower part of the main chamber. The beams passing through the plasma are received at a detector array consisting of a half-wave rotator and modules consisting of an integrated lens antenna and mixer. The local oscillator beam is expanded by another pair of Powell lenses and received at the detector array as well. The signal frequencies are down-converted to 10–70 MHz intermediate frequencies, and then their phases are converted into line-integrated electron densities. The optical system was optimized using Gaussian beam approximation and the optics design tool, CODE V. For the commissioning of the complete system, a single-channel setup was first tested and verified by comparing the results with a V-band frequency sweeping interferometer. The data from five channels were then obtained and compared with the time trace obtained by 1 kHz Thomson scattering at the midplane of the plasma.
- 1 April 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (4)
Development of a multi-channel mm-wave interferometer for the versatile experiment spherical torus (VEST)
The 94 GHz single-channel interferometer at the versatile experiment spherical torus has been upgraded into a multi-channel heterodyne interferometer for electron density profile measurements. Five Gaussian beam chords generated by a pair of Powell lenses and collimating lenses are vertically spaced at 75 mm intervals from the midplane to the lower part of the main chamber. The beams passing through the plasma are received at a detector array consisting of a half-wave rotator and modules consisting of an integrated lens antenna and mixer. The local oscillator beam is expanded by another pair of Powell lenses and received at the detector array as well. The signal frequencies are down-converted to 10–70 MHz intermediate frequencies, and then their phases are converted into line-integrated electron densities. The optical system was optimized using Gaussian beam approximation and the optics design tool, CODE V. For the commissioning of the complete system, a single-channel setup was first tested and verified by comparing the results with a V-band frequency sweeping interferometer. The data from five channels were then obtained and compared with the time trace obtained by 1 kHz Thomson scattering at the midplane of the plasma.
- Open Access
- 1 March 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (3)
Criterion for long sustained highly peaked ion temperature in diverted configuration of KSTAR tokamak
In the context of KSTAR plasma research, the discovery of the fast ion regulated enhanced mode is noteworthy due to its remarkable ability to maintain ion temperatures exceeding up to 10 keV for a few tens of seconds, avoid impurity accumulation, and keep low loop voltages. This new plasma operating scenario is achieved in a diverted configuration plasma by avoiding the H-mode transitions with sufficient additional power for the transition. Keeping the density low is the primary method for the avoidance. Additionally, adjustments to other parameters (plasma shape, neutral beam injection, and toroidal magnetic field) associated with the H-mode threshold power are applied to inhibit the transition process. This paper includes an experimental analysis and discussion of these findings.
- 1 March 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (3)
Open AccessCriterion for long sustained highly peaked ion temperature in diverted configuration of KSTAR tokamak
In the context of KSTAR plasma research, the discovery of the fast ion regulated enhanced mode is noteworthy due to its remarkable ability to maintain ion temperatures exceeding up to 10 keV for a few tens of seconds, avoid impurity accumulation, and keep low loop voltages. This new plasma operating scenario is achieved in a diverted configuration plasma by avoiding the H-mode transitions with sufficient additional power for the transition. Keeping the density low is the primary method for the avoidance. Additionally, adjustments to other parameters (plasma shape, neutral beam injection, and toroidal magnetic field) associated with the H-mode threshold power are applied to inhibit the transition process. This paper includes an experimental analysis and discussion of these findings.
- Open Access
- 6 November 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (12) , 129501
Corrigendum: Integrated RMP-based ELM-crash-control process for plasma performance enhancement during ELM crash suppression in KSTAR (2023 Nucl. Fusion 63 086032)
- 6 November 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 63 (12) , 129501
Open AccessCorrigendum: Integrated RMP-based ELM-crash-control process for plasma performance enhancement during ELM crash suppression in KSTAR (2023 Nucl. Fusion 63 086032)