Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Stefano Pasini has a total of 61 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Beyond CdS: Buffer Layers, Front Interfaces and Junction Engineering in p-Type Thin-Film Solar Cells

    by Stefano Pasini, Sara Russo, Muhammad Kashif, Alessio Bosio

    Cadmium sulfide has been widely used as a conventional n-type window/buffer layer or heterojunction partner in several p-type thin-film solar cells, including CdTe/CdSeTe-, chalcopyrite-, kesterite-, antimony chalcogenide-, tin sulfide- and iron pyrite-based devices. Its success is related to its ability to form suitable heterojunctions, partially passivate absorber surfaces and provide favorable electronic selectivity. However, the parasitic absorption associated with the relatively narrow band gap of CdS, the toxicity and waste-management issues related to cadmium-containing auxiliary layers and the need for improved band alignment have motivated extensive research on CdS-free window and buffer layers. This review summarizes the main efforts devoted to replacing CdS in thin-film solar cells based on absorbers such as CdTe/CdSeTe, CIS, CIGS, CZTS, CZTSe, CZTSSe, Sb2S3, Sb2Se3, Sb2(S,Se)3, SnS and FeS2. The most investigated alternative materials, including Zn(O,S), ZnS, In2S3, ZnMgO, ZnSnO, TiO2, SnO2 and SnS2, are discussed with emphasis on their optical properties, band alignment, interface quality, deposition methods and impact on device performance. The analysis highlights that CdS replacement cannot be treated as a universal material substitution problem. Instead, each absorber and device architecture requires a specific front-interface design, where chemical compatibility, conduction band offset, defect passivation, optical transparency and process-induced interfacial modifications play a decisive role. CdS-free approaches are relatively mature for CdTe/CdSeTe- and CIGS-based solar cells, whereas kesterite absorbers, antimony chalcogenides and SnS still require further interface engineering. In FeS2, by contrast, buffer-layer substitution remains secondary to the control of intrinsic surface and bulk electronic defects. This review provides a concise comparison of the most relevant CdS-free front/window materials and identifies key challenges for the future design of sustainable thin-film solar cells.


  • Open Access

    Water-assisted grown ZnO transparent conductive oxide enables efficient thin-film solar cells

    by Stefano Pasini, Andrea Baraldi, Ildikò Cora, Gianluca Foti, Muhammad Kashif, Francesco Mezzadri, Ifeanyi John Onuorah, Antonella Parisini, Béla Pécz, Samaneh Shapouri, et al.


  • Open Access

    Effect of lithium diffusion into Ga2O3 thin films

    by A. Sacchi, M. Sidoli, A. Ardenghi, O. Bierwagen, J. Kler, A. Falkenstein, R.A. De Souza, M. Martin, D. Spallek, J. Lähnemann, et al.


  • Open Access

    Substrate-Dependent Characteristics of CuSbS2 Solar Absorber Layers Grown by Spray Pyrolysis

    by Samaneh Shapouri, Elnaz Irani, Payam Rajabi Kalvani, Stefano Pasini, Gianluca Foti, Antonella Parisini, Alessio Bosio

    Copper antimony sulfide (CuSbS2) is an affordable and eco-friendly solar absorber with an optimal bandgap and high absorption coefficient, and it stands out as a promising candidate for thin-film solar cells. This study investigates the effects of indium tin oxide (ITO), fluorine-doped tin oxide (FTO), and glass substrates on the microstructural, morphological, and optical properties of CuSbS2 (CAS) layers synthesized via spray pyrolysis. X-ray Diffraction (XRD) and Raman spectroscopy analyses revealed that CAS phases formed on ITO and FTO substrates exhibited a phase composition without additional copper phases. However, the CAS layer on glass contained a copper sulfide (CuS) phase, which can be detrimental for solar cell applications. Furthermore, the influences of the substrate morphology and contact angle on the growth mechanisms of CAS layers was examined, highlighting the relationship between the substrate micromorphology and the resultant film characteristics. Advanced image processing techniques applied to Atomic Force Microscopy (AFM) images of the substrate surfaces facilitated a comprehensive comparison with the surface characteristics of the CAS films grown on those substrates. Field Emission Scanning Electron Microscopy (FESEM) indicated that CAS layers on ITO possessed larger grains than FTO, whereas those on FTO exhibited lower roughness with a more uniform grain distribution. Notably, the optical properties of the CAS layers correlated strongly with their microstructural and morphological characteristics. This work highlights the critical influence of substrate choice on the growth and characteristics of CAS layers through a comparative analysis.


  • Open Access

    Effect of Heterojunction Characteristics and Deep Electronic Levels on the Performance of (Cd,Zn)S/Sb2Se3 Solar Cells

    by Alessio Bosio, Stefano Pasini, Donato Spoltore, Gianluca Foti, Antonella Parisini, Maura Pavesi, Samaneh Shapouri, Ildikó Cora, Zsolt Fogarassy, Roberto Fornari

    Antimony selenide (Sb2Se3) is an Earth-abundant and non-toxic material that stands out as a promising absorber for the fabrication of thin film solar cells. Despite significant advancements in recent years, all the devices reported in the literature exhibit open-circuit voltages well below the theoretical value. Identifying the factors contributing to this low voltage is an essential step for increasing the efficiency beyond the recently attained 10% milestone and moving closer to the theoretical limit. In this paper, we present the results of an in-depth analysis of a Sb2Se3 solar cell in the common superstrate configuration. By making use of current density–voltage characteristic as a function of both temperature and wavelength, capacitance–voltage measurements, and admittance spectroscopy, we ascribe the low open-circuit voltage to the presence of a potential barrier within the absorber material near the junction interface Furthermore, it was observed that the junction behavior in the dark and under illumination changes, which is compatible with the presence of deep electronic levels connected with intrinsic point defects.


  • Open Access

    Planar hybrid UV-C photodetectors based on aerosol-jet printed PEDOT:PSS on different Ga2O3 thin films

    by F. Mattei, D. Vurro, D. Spoltore, M. Pavesi, P. Rajabi Kalvani, S. Pasini, G. Foti, P. D'Angelo, A. Bosio, A. Baraldi, et al.


  • Open Access

    A Review on the Fundamental Properties of Sb2Se3-Based Thin Film Solar Cells

    by Alessio Bosio, Gianluca Foti, Stefano Pasini, Donato Spoltore

    There has been a recent surge in interest toward thin film-based solar cells, specifically new absorber materials composed by Earth-abundant and non-toxic elements. Among these materials, antimony selenide (Sb2Se3) is a good candidate due to its peculiar properties, such as an appropriate bandgap that promises a theoretical maximum power conversion efficiency of 33% and an absorption coefficient of around 105 cm−1, enabling its use as a thin film absorber layer. However, charge carrier transport has been revealed to be problematic due to its cumbersome structure and the lack of a doping strategy. In this work, we aim to provide a clear picture of the state-of-the-art regarding research on Sb2Se3-based solar cells and its prospects, from the successful achievements to the challenges that are still to be overcome. We also report on the key parameters of antimony selenide with a close focus on the different characteristics associated with films grown from different techniques.


  • Open Access

    Sb2Se3 Polycrystalline Thin Films Grown on Different Window Layers

    by Stefano Pasini, Donato Spoltore, Antonella Parisini, Gianluca Foti, Stefano Marchionna, Salvatore Vantaggio, Roberto Fornari, Alessio Bosio

    Sb2Se3 is a typical V2VI3 binary chalcogenide compound characterized by a single crystalline phase and a fixed composition. Sb2Se3 displays a narrow energy gap ranging from 1.1 to 1.3 eV, which are quite optimal values for single-junction solar cells. Earth-abundant and non-toxic components make this material a good candidate for low-cost thin-film solar cells. In substrate configuration, a world record efficiency of 9.2% was recently obtained. Sb2Se3 thin films exhibit an accentuated predisposition to form (Sb4Se6)n ribbons along the [001] direction. This anisotropy heavily influences the charge transport of the photogenerated carriers. In this work, structural characterization of the Sb2Se3 films showed that the crystalline quality and preferential orientation are strongly dependent on the window layer used. To better understand the growth mechanism, Sb2Se3 thin films were deposited by close-spaced sublimation on five different window layers, such as CdS, CdS:F, CdSe, As2S3, and ZnCdS. Sb2Se3-based solar cells, realized in superstrate configuration on these different substrates, evidently demonstrate the influence of the Sb2Se3 preferential orientation on the photovoltaic parameters.


  • Open Access

    The History of Photovoltaics with Emphasis on CdTe Solar Cells and Modules

    by Alessio Bosio, Stefano Pasini, Nicola Romeo

    Among thin-film photovoltaic technology, cadmium telluride (CdTe) has achieved a truly impressive development that can commercially compete with silicon, which is still the king of the market. Solar cells made on a laboratory scale have reached efficiencies close to 22%, while modules made with fully automated in-line machines show efficiencies above 18%. This success represents the result of over 40 years of research, which led to effective and consolidated production processes. Based on a large literature survey on photovoltaics and on the results of research developed in our laboratories, we present the fabrication processes of both CdTe polycrystalline thin-film solar cells and photovoltaic modules. The most common substrates, the constituent layers, their interaction, the interfaces and the different “tricks” necessary to obtain highly efficient devices will be analyzed. A realistic industrial production process will be analytically described. Moreover, environmental aspects, end-of-life recycling and the life cycle assessment of CdTe-based modules will be deepened and discussed.