Georgi Dobrikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Georgi Dobrikov has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mariya Aleksandrova
Department of Microelectronics, Technical University of Sofia, 1756 Sofia, Bulgaria
3 shared publications - Alexander Lukin
Western-Caucasus Research Center
1 shared publication Andrey Brigadin
Swissimpianti Sagl, 6828 Balerna, Switzerland
1 shared publication- Arya Sohan
CASEST, School of Physics, University of Hyderabad, Hyderabad 500046, Telangana, India
1 shared publication - Georgi Kolev
Department of Microelectronics, Technical University of Sofia, 1000 Sofia, Bulgaria
1 shared publication - Ivaylo Pandiev
Department of Electronics, Faculty of Electronic Engineering and Technologies (FEET), Technical University of Sofia, 1000 Sofia, Bulgaria
1 shared publication
Latest Publications
- Open Access
- 15 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 2066
Unlocking the Carbyne-Enriched Nanocoating Sensitivity to Volatile Organic Vapors with Plasma-Driven Deposition onto Bulk Micromachined Silicon Membranes
Due to the unique combination of physicochemical and structural properties of carbyne-enriched nanocoatings, they can be used for the development of high-end electronic devices. We propose using it for the development of sensor platforms based on silicon bulk micromachined membranes that serve as a part of microcapacitors with flexible electrodes, with various sizes and topologies. The carbyne-enriched nanocoating was grown using the ion-assisted pulse-plasma deposition method in the form of 2D-ordered linear-chain carbon with interchain spacing in the range of approximately 4.8–5.03 Å. The main characteristics of the fabricated sensors, such as dynamic range, sensitivity, linearity, response, and recovery times, were measured as a function of the ethanol concentration and compared for the different sizes of the micromembranes and for the different surface states, such as patterned and non-patterned. The obtained results are the first step in the further optimization of these sensor platforms to reach more precise detection of volatile organic compounds for the needs of the healthcare, air monitoring, and other relevant fields of human health.
- 15 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 2066
Open AccessUnlocking the Carbyne-Enriched Nanocoating Sensitivity to Volatile Organic Vapors with Plasma-Driven Deposition onto Bulk Micromachined Silicon Membranes
Due to the unique combination of physicochemical and structural properties of carbyne-enriched nanocoatings, they can be used for the development of high-end electronic devices. We propose using it for the development of sensor platforms based on silicon bulk micromachined membranes that serve as a part of microcapacitors with flexible electrodes, with various sizes and topologies. The carbyne-enriched nanocoating was grown using the ion-assisted pulse-plasma deposition method in the form of 2D-ordered linear-chain carbon with interchain spacing in the range of approximately 4.8–5.03 Å. The main characteristics of the fabricated sensors, such as dynamic range, sensitivity, linearity, response, and recovery times, were measured as a function of the ethanol concentration and compared for the different sizes of the micromembranes and for the different surface states, such as patterned and non-patterned. The obtained results are the first step in the further optimization of these sensor platforms to reach more precise detection of volatile organic compounds for the needs of the healthcare, air monitoring, and other relevant fields of human health.
- Open Access
Pyroelectric Properties of BaxSr(1−x)TiO3/PVDF-TrFE Coating on Silicon
Bilayer coatings of barium strontium titanate (BaxSr(1−x)TiO3)/poly [(vinylidenefluoride-co-trifluoroethylene] (PVDF-TrFE) were integrated on silicon Si (100) for pyroelectric devices. Pyroelectric properties of the composite were determined for different electrode materials (silver and aluminum) and different electrodes configurations creating an electric field in parallel and in-plane direction in the ferroelectric coating. For this purpose, parallel-plate and planar interdigital capacitors were fabricated. Anisotropy in the pyroelectric response was noted for the different directions of the measured electrical potential. The dynamic method was used to evaluate the pyroelectric properties in the temperature range of 22 to 48 °C. Pyroelectric response with a higher value was observed at the one plate’s configuration of interdigital electrodes. The voltage response was the strongest when silver contacts were used. At temperatures near room temperature, the voltage increased by 182 µV at resolution of 7 µV/°C for the in-plain device configuration, vs. 290 µV at a resolution of 11 µV/°C for the out-of-plain configuration. A relationship between the surface morphology of the ferroelectric oxide and oxide/polymer coating and the pyroelectric voltage was also found, proving the smoothening effect of the introduction of polymer PVDF-TrFE over the BaSrTiO3 grains.
Open AccessPyroelectric Properties of BaxSr(1−x)TiO3/PVDF-TrFE Coating on Silicon
Bilayer coatings of barium strontium titanate (BaxSr(1−x)TiO3)/poly [(vinylidenefluoride-co-trifluoroethylene] (PVDF-TrFE) were integrated on silicon Si (100) for pyroelectric devices. Pyroelectric properties of the composite were determined for different electrode materials (silver and aluminum) and different electrodes configurations creating an electric field in parallel and in-plane direction in the ferroelectric coating. For this purpose, parallel-plate and planar interdigital capacitors were fabricated. Anisotropy in the pyroelectric response was noted for the different directions of the measured electrical potential. The dynamic method was used to evaluate the pyroelectric properties in the temperature range of 22 to 48 °C. Pyroelectric response with a higher value was observed at the one plate’s configuration of interdigital electrodes. The voltage response was the strongest when silver contacts were used. At temperatures near room temperature, the voltage increased by 182 µV at resolution of 7 µV/°C for the in-plain device configuration, vs. 290 µV at a resolution of 11 µV/°C for the out-of-plain configuration. A relationship between the surface morphology of the ferroelectric oxide and oxide/polymer coating and the pyroelectric voltage was also found, proving the smoothening effect of the introduction of polymer PVDF-TrFE over the BaSrTiO3 grains.
- Open Access
- 7 May 2020
- Published by MDPI AG in Materials Proceedings
- Vol. 2 (1) , 11
Study of Lead-Free Ferroelectric Composite Coatings by Impedance Spectroscopy
The aim of the study is the preparation and electrical characterization of lead-free ferroelectric oxide BaSrTiO3 in the composition with a piezoelectric polymer. The properties of the deposited films were compared with pristine oxide. Atomic force microscopy showed a smooth surface, and a regular and homogeneous distribution of particles of both components in the composite films. The dielectric properties (electric permittivity and dielectric loss) were investigated at different temperatures ranging from 5 to 130 °C. Impedance spectroscopy was applied in the frequency range 100–100 kHz. The dielectric constant increase with the addition of a piezoelectric polymer to the ceramic phase was demonstrated. It can be seen that the interface conditions at the electrodes are improved after inserting a piezoelectric polymer. The interpretation of the plots of the complex impedance vs. frequency, and the real part of the impedance vs. the imaginary part, give information about the polarization process revealed in the structures.
- 7 May 2020
- Published by MDPI AG in Materials Proceedings
- Vol. 2 (1) , 11
Open AccessStudy of Lead-Free Ferroelectric Composite Coatings by Impedance Spectroscopy
The aim of the study is the preparation and electrical characterization of lead-free ferroelectric oxide BaSrTiO3 in the composition with a piezoelectric polymer. The properties of the deposited films were compared with pristine oxide. Atomic force microscopy showed a smooth surface, and a regular and homogeneous distribution of particles of both components in the composite films. The dielectric properties (electric permittivity and dielectric loss) were investigated at different temperatures ranging from 5 to 130 °C. Impedance spectroscopy was applied in the frequency range 100–100 kHz. The dielectric constant increase with the addition of a piezoelectric polymer to the ceramic phase was demonstrated. It can be seen that the interface conditions at the electrodes are improved after inserting a piezoelectric polymer. The interpretation of the plots of the complex impedance vs. frequency, and the real part of the impedance vs. the imaginary part, give information about the polarization process revealed in the structures.