Alexandru-Florian Popov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexandru-Florian Popov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dragoș-Vasile Bratu
Department of Automatics and Information Technology, Transilvania University of Brasov, 500036 Brașov, Romania
2 shared publications - Sorin-Aurel Moraru
Transilvania University of Brasov
2 shared publications - Dominic Mircea Kristály
Department of Automatics and Information Technology, Faculty of Electrical Engineering and Computer Science, Transilvania University of Brasov, Brasov, Romania
1 shared publication M Fratu
Department of Building Services, Transilvania University of Braşov, Romania
1 shared publication- Maria-Alexandra Zolya
Department of Automatics and Information Technology, Transilvania University of Brasov, 500036 Brașov, Romania
1 shared publication
Latest Publications
- Open Access
- 13 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4874
A Method for Using GSM Technology and SCADA Systems to Monitor and Control Decommissioned and Partially Decommissioned Railway Stations
Railway systems are sometimes faced with the necessity of decommissioning railway stations due to issues in the electricity supply system, control system failures, or a decrease in train traffic. In order for fully or partially decommissioned stations to maintain functionality and turnout availability, the researchers propose the use of a computer system utilizing GSM technology. Using AES-encrypted SMS messages, GSM signaling can be applied to a wide range of electrical equipment at decommissioned stations, enabling monitoring and control of these installations remotely, as well as allowing for integration into an existing SCADA system. This study attempts to estimate the reduction in total delays and operating cost that would arise when implementing this control system in a low-resource setting. An impact and cost analysis was performed on a rail section with partially decommissioned stations (Brașov–Codlea, Romania), to ascertain whether this control method would result in significant delay and cost reductions. The analyzed data show that the proposed control system can significantly reduce delays and costs on railway lines with decommissioned stations, thus allowing for a more efficient use of resources. By leveraging technology to monitor and control electrical installations remotely, the need for physical presence at the decommissioned station is eliminated. Overall, the research described represents a significant step towards the more efficient and safe use of railway infrastructure, and could potentially lead to the reactivation of previously decommissioned stations, providing benefits for both passengers and freight transport operators.
- 13 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4874
Open AccessA Method for Using GSM Technology and SCADA Systems to Monitor and Control Decommissioned and Partially Decommissioned Railway Stations
Railway systems are sometimes faced with the necessity of decommissioning railway stations due to issues in the electricity supply system, control system failures, or a decrease in train traffic. In order for fully or partially decommissioned stations to maintain functionality and turnout availability, the researchers propose the use of a computer system utilizing GSM technology. Using AES-encrypted SMS messages, GSM signaling can be applied to a wide range of electrical equipment at decommissioned stations, enabling monitoring and control of these installations remotely, as well as allowing for integration into an existing SCADA system. This study attempts to estimate the reduction in total delays and operating cost that would arise when implementing this control system in a low-resource setting. An impact and cost analysis was performed on a rail section with partially decommissioned stations (Brașov–Codlea, Romania), to ascertain whether this control method would result in significant delay and cost reductions. The analyzed data show that the proposed control system can significantly reduce delays and costs on railway lines with decommissioned stations, thus allowing for a more efficient use of resources. By leveraging technology to monitor and control electrical installations remotely, the need for physical presence at the decommissioned station is eliminated. Overall, the research described represents a significant step towards the more efficient and safe use of railway infrastructure, and could potentially lead to the reactivation of previously decommissioned stations, providing benefits for both passengers and freight transport operators.
- Open Access
- 1 April 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1138 (1) , 012038
Reactive power compensation in the railway electrical traction system, using synchronous machines controlled by SCADA
This article brings forward a solution for compensating the reactive power of the railway electrical traction system. Using the V-characteristics of the synchronous machine, reactive power can be produced or absorbed from the power supply network, keeping the power factor at a value as close to 1 as possible. Given that the load consumed by the railway electrical traction system is variable, it is necessary to be able to promptly correct the power factor. The SCADA system will change the synchronous machine’s operating characteristics relative as a function of the angle between the voltage and the current that are set at a given time by the consumers (electrical locomotives) passing through the railway section. By compensating the reactive power, the amount of active power supplied to the electrical network of the railway traction system is increased, without the need to modify the cross-section of the electrical conductors.
- 1 April 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1138 (1) , 012038
Open AccessReactive power compensation in the railway electrical traction system, using synchronous machines controlled by SCADA
This article brings forward a solution for compensating the reactive power of the railway electrical traction system. Using the V-characteristics of the synchronous machine, reactive power can be produced or absorbed from the power supply network, keeping the power factor at a value as close to 1 as possible. Given that the load consumed by the railway electrical traction system is variable, it is necessary to be able to promptly correct the power factor. The SCADA system will change the synchronous machine’s operating characteristics relative as a function of the angle between the voltage and the current that are set at a given time by the consumers (electrical locomotives) passing through the railway section. By compensating the reactive power, the amount of active power supplied to the electrical network of the railway traction system is increased, without the need to modify the cross-section of the electrical conductors.
- Open Access
- 15 March 2019
- Published by Universitatea Dunarea de Jos din Galati in The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science
- Vol. 42 (1) , 42-47
Remote Control of Railway Switch Heating Using GSM Modems
This research activity examines the possibility of remote control of the heating of railway switches. The study and implementation of the remote-control system of resistive heaters using the Global Mobile Communication System (GSM) through SMS messages (Short Message Service) and AT (attention) commands is presented in this article. The research works envisaged are convergent on the functionality of a GSM protocol, which allows the user to control the heating of the remote railway switches, away from the place where the switches were installed. The notions of serial communication, electronic control and AT control have been applied to expand the system. To increase the robustness of the system, a feedback mechanism was introduced so that users will be able to get a feedback status of the system when the command was successfully sent or in the case of voltage drops and system restarts.
- 15 March 2019
- Published by Universitatea Dunarea de Jos din Galati in The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science
- Vol. 42 (1) , 42-47
Open AccessRemote Control of Railway Switch Heating Using GSM Modems
This research activity examines the possibility of remote control of the heating of railway switches. The study and implementation of the remote-control system of resistive heaters using the Global Mobile Communication System (GSM) through SMS messages (Short Message Service) and AT (attention) commands is presented in this article. The research works envisaged are convergent on the functionality of a GSM protocol, which allows the user to control the heating of the remote railway switches, away from the place where the switches were installed. The notions of serial communication, electronic control and AT control have been applied to expand the system. To increase the robustness of the system, a feedback mechanism was introduced so that users will be able to get a feedback status of the system when the command was successfully sent or in the case of voltage drops and system restarts.