Jørgen Hald
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jørgen Hald has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Antoine Richard
Acoustic Technology, Technical University of Denmark, 2800 Kongens Lyngby, Denmark
2 shared publications- Cheol-Ho Jeong
Technical University of Denmark
2 shared publications - Efren Fernandez-Grande
Departamento de Ingeniería Audiovisual Y Comunicaciones, Universidad Politécnica de Madrid
1 shared publication Jonas Brunskog
Acoust. Technol., Tech. Univ. of Denmark, Kgs. Lyngby, Denmark
1 shared publicationKarim Haddad
Brüel & Kjaer SVM A/S, Skodsborgvej 307, 2850 Naerum, Denmark
1 shared publication- Karim Haddad
Brüel & Kjær Sound & Vib. Measurement A/S, Nærum, Denmark
1 shared publication
Latest Publications
- 1 April 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (4) , 2211-2221
A comparison of compressive equivalent source methods for distributed sources
Sparse sound-field reconstruction methods based on compressive sensing and the equivalent source method have gained a lot of interest in recent years, offering a wide frequency range. An irregular array must be employed, and the sound field must be representable by a sparse vector of source-model amplitudes. With few and concentrated physical sources, the sparsity assumption can be fulfilled, but distributed sources cause problems. Several methods have therefore been introduced to support sparse representation of distributed sources. One set of such methods represents the amplitude vector as a linear combination of modal amplitude distributions. In that case, the coefficient vector just has to be sparse. The present paper gives an overview of such methods, and the performance of the methods is compared based on a set of simulated measurements. Overall the modal representations work well if the true source distribution can be represented by relatively few modes. The results show that even for a vibrating plate this may not be the case if the source model size does not match the plate size and/or if a non-central plate excitation is applied. If, in addition, there are also compact sources, then the basic method without modes may be the best choice.
- 1 April 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (4) , 2211-2221
A comparison of compressive equivalent source methods for distributed sources
Sparse sound-field reconstruction methods based on compressive sensing and the equivalent source method have gained a lot of interest in recent years, offering a wide frequency range. An irregular array must be employed, and the sound field must be representable by a sparse vector of source-model amplitudes. With few and concentrated physical sources, the sparsity assumption can be fulfilled, but distributed sources cause problems. Several methods have therefore been introduced to support sparse representation of distributed sources. One set of such methods represents the amplitude vector as a linear combination of modal amplitude distributions. In that case, the coefficient vector just has to be sparse. The present paper gives an overview of such methods, and the performance of the methods is compared based on a set of simulated measurements. Overall the modal representations work well if the true source distribution can be represented by relatively few modes. The results show that even for a vibrating plate this may not be the case if the source model size does not match the plate size and/or if a non-central plate excitation is applied. If, in addition, there are also compact sources, then the basic method without modes may be the best choice.
- Open Access
- 1 January 2019
- Published by Elsevier in Applied Acoustics
- Vol. 143, 74-83
In-situ impedance and absorption coefficient measurements using a double-layer microphone array
- 1 January 2019
- Published by Elsevier in Applied Acoustics
- Vol. 143, 74-83
Open AccessIn-situ impedance and absorption coefficient measurements using a double-layer microphone array
- Open Access
- 1 June 2018
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 143 (6) , 3758-3769
A comparison of iterative sparse equivalent source methods for near-field acoustical holography
During the past decade, several publications have described the use of compressive sensing principles to extend the frequency range supported by a given irregular microphone array for near-field acoustic holography. The applied numerical source model has typically been of the type used for the equivalent source method, i.e., a mesh of point sources, and a one-norm regularized inverse problem has been solved using a very stable, but slow interior-point optimization algorithm. A few publications have investigated the use of simpler and faster iterative algorithms. The present paper gives a brief description of five such iterative algorithms, and it compares their performances with that of the interior-point algorithm based on a set of simulated measurements. A particular focus is on the suitability for industrial applications. Finally, an optimal choice of methodology is discussed based on the presented limited set of simulated tests.
- 1 June 2018
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 143 (6) , 3758-3769
Open AccessA comparison of iterative sparse equivalent source methods for near-field acoustical holography
During the past decade, several publications have described the use of compressive sensing principles to extend the frequency range supported by a given irregular microphone array for near-field acoustic holography. The applied numerical source model has typically been of the type used for the equivalent source method, i.e., a mesh of point sources, and a one-norm regularized inverse problem has been solved using a very stable, but slow interior-point optimization algorithm. A few publications have investigated the use of simpler and faster iterative algorithms. The present paper gives a brief description of five such iterative algorithms, and it compares their performances with that of the interior-point algorithm based on a set of simulated measurements. A particular focus is on the suitability for industrial applications. Finally, an optimal choice of methodology is discussed based on the presented limited set of simulated tests.
- 1 August 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 142 (2) , 846-854
Removal of incoherent noise from an averaged cross-spectral matrix
Measured cross-spectral matrices (CSMs) from a microphone array will in some cases be contaminated by severe incoherent noise signals in the individual channels. A typical example is flow noise generated in the individual microphones when measuring in a wind tunnel. Assuming stationary signals and performing long-time averaging, the contamination will be concentrated on the CSM diagonal. When the CSM is used for traditional frequency-domain beamforming, diagonal removal (DR) will avoid use of the diagonal. DR is effective at suppressing the contamination effects, but it also has some side effects. With other beamforming algorithms and in connection with acoustic holography, however, the diagonal of the CSM is needed. The present paper describes a method for removal of incoherent noise contamination from the CSM diagonal. The method formulates the problem as a semidefinite program, which is a convex optimization problem that can be solved very efficiently and with guaranteed convergence properties. A first numerical study investigates the question, whether the semidefinite program formulation will provide in all cases the desired output. A second numerical study investigates the limitations introduced by off-diagonal noise contributions due to finite averaging time. The results of that study are backed up by results from a practical measurement.
- 1 August 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 142 (2) , 846-854
Removal of incoherent noise from an averaged cross-spectral matrix
Measured cross-spectral matrices (CSMs) from a microphone array will in some cases be contaminated by severe incoherent noise signals in the individual channels. A typical example is flow noise generated in the individual microphones when measuring in a wind tunnel. Assuming stationary signals and performing long-time averaging, the contamination will be concentrated on the CSM diagonal. When the CSM is used for traditional frequency-domain beamforming, diagonal removal (DR) will avoid use of the diagonal. DR is effective at suppressing the contamination effects, but it also has some side effects. With other beamforming algorithms and in connection with acoustic holography, however, the diagonal of the CSM is needed. The present paper describes a method for removal of incoherent noise contamination from the CSM diagonal. The method formulates the problem as a semidefinite program, which is a convex optimization problem that can be solved very efficiently and with guaranteed convergence properties. A first numerical study investigates the question, whether the semidefinite program formulation will provide in all cases the desired output. A second numerical study investigates the limitations introduced by off-diagonal noise contributions due to finite averaging time. The results of that study are backed up by results from a practical measurement.
- 1 May 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 141 (5_Suppleme) , 3842
Estimation of surface impedance using different types of microphone arrays
This study investigates microphone array methods to measure the angle dependent surface impedance of acoustic materials. The methods are based on the reconstruction of the sound field on the surface of the material, using a wave expansion formulation. The reconstruction of both the pressure and the particle velocity leads to an estimation of the surface impedance for a given angle of incidence. A porous type absorber sample is tested experimentally in anechoic conditions for different array geometries, sample sizes, incidence angles, and distances between the array and sample. In particular, the performances of a rigid spherical array and a double layer planar array are examined. The use of sparse array processing methods and conventional regulariation approaches are studied. In addition, the influence of the size of the sample on the surface impedance estimation is investigated using both experimental data and numerical simulations with a boundary element model. Results indicate that the small distance between the planar array and the sample favors a more robust estimation.
- 1 May 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 141 (5_Suppleme) , 3842
Estimation of surface impedance using different types of microphone arrays
This study investigates microphone array methods to measure the angle dependent surface impedance of acoustic materials. The methods are based on the reconstruction of the sound field on the surface of the material, using a wave expansion formulation. The reconstruction of both the pressure and the particle velocity leads to an estimation of the surface impedance for a given angle of incidence. A porous type absorber sample is tested experimentally in anechoic conditions for different array geometries, sample sizes, incidence angles, and distances between the array and sample. In particular, the performances of a rigid spherical array and a double layer planar array are examined. The use of sparse array processing methods and conventional regulariation approaches are studied. In addition, the influence of the size of the sample on the surface impedance estimation is investigated using both experimental data and numerical simulations with a boundary element model. Results indicate that the small distance between the planar array and the sample favors a more robust estimation.
- 1 April 2016
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 139 (4) , 1508-1517
Fast wideband acoustical holography
Patch near-field acoustical holography methods like statistically optimized near-field acoustical holography and equivalent source method are limited to relatively low frequencies, where the average array-element spacing is less than half of the acoustic wavelength, while beamforming provides useful resolution only at medium-to-high frequencies. With adequate array design, both methods can be used with the same array. But for holography to provide good low-frequency resolution, a small measurement distance is needed, whereas beamforming requires a larger distance to limit sidelobe issues. The wideband holography method of the present paper was developed to overcome that practical conflict. Only a single measurement is needed at a relatively short distance and a single result is obtained covering the full frequency range. The method uses the principles of compressed sensing: A sparse sound field representation is assumed with a chosen set of basis functions, a measurement is taken with an irregular array, and the inverse problem is solved with a method that enforces sparsity in the coefficient vector. Instead of using regularization based on the 1-norm of the coefficient vector, an iterative solution procedure is used that promotes sparsity. The iterative method is shown to provide very similar results in most cases and to be computationally much more efficient.
- 1 April 2016
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 139 (4) , 1508-1517
Fast wideband acoustical holography
Patch near-field acoustical holography methods like statistically optimized near-field acoustical holography and equivalent source method are limited to relatively low frequencies, where the average array-element spacing is less than half of the acoustic wavelength, while beamforming provides useful resolution only at medium-to-high frequencies. With adequate array design, both methods can be used with the same array. But for holography to provide good low-frequency resolution, a small measurement distance is needed, whereas beamforming requires a larger distance to limit sidelobe issues. The wideband holography method of the present paper was developed to overcome that practical conflict. Only a single measurement is needed at a relatively short distance and a single result is obtained covering the full frequency range. The method uses the principles of compressed sensing: A sparse sound field representation is assumed with a chosen set of basis functions, a measurement is taken with an irregular array, and the inverse problem is solved with a method that enforces sparsity in the coefficient vector. Instead of using regularization based on the 1-norm of the coefficient vector, an iterative solution procedure is used that promotes sparsity. The iterative method is shown to provide very similar results in most cases and to be computationally much more efficient.