Aldair E. Gongora
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aldair E. Gongora has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Keith A. Brown
Boston University
5 shared publications - Kelsey L. Snapp
Soldier Protection Directorate, U.S. Army Combat Capabilities Development Command Soldier Center, Natick, MA, USA
4 shared publications - Elise F. Morgan
Department of Biomedical Engineering Boston University Boston Massachusetts USA
2 shared publications - Pratanu Roy
Lawrence Livermore National Laboratory, Livermore, USA
2 shared publications - Verda Saygin
Department of Mechanical Engineering, Boston University, 110 Cummington Mall, Boston, Massachusetts 02215, United States
2 shared publications - Adedire D. Adesiji
Department of Mechanical Engineering, Boston University, Boston, MA, USA
1 shared publication
Latest Publications
- Open Access
- 8 August 2026
- Published by Association for Computing Machinery (ACM)
- p. 11740-11749
Tensor Methods: A Unified and Interpretable Approach for Material Design
- 8 August 2026
- Published by Association for Computing Machinery (ACM)
- p. 11740-11749
Open AccessTensor Methods: A Unified and Interpretable Approach for Material Design
- 18 December 2024
- Published by Springer Nature in Nature Chemical Engineering
- Vol. 1 (12) , 731-740
Accelerating climate technologies through the science of scale-up
- 18 December 2024
- Published by Springer Nature in Nature Chemical Engineering
- Vol. 1 (12) , 731-740
Accelerating climate technologies through the science of scale-up
- Open Access
- 21 May 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-9
Superlative mechanical energy absorbing efficiency discovered through self-driving lab-human partnership
Energy absorbing efficiency is a key determinant of a structure’s ability to provide mechanical protection and is defined by the amount of energy that can be absorbed prior to stresses increasing to a level that damages the system to be protected. Here, we explore the energy absorbing efficiency of additively manufactured polymer structures by using a self-driving lab (SDL) to perform >25,000 physical experiments on generalized cylindrical shells. We use a human-SDL collaborative approach where experiments are selected from over trillions of candidates in an 11-dimensional parameter space using Bayesian optimization and then automatically performed while the human team monitors progress to periodically modify aspects of the system. The result of this human-SDL campaign is the discovery of a structure with a 75.2% energy absorbing efficiency and a library of experimental data that reveals transferable principles for designing tough structures.
- 21 May 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-9
Open AccessSuperlative mechanical energy absorbing efficiency discovered through self-driving lab-human partnership
Energy absorbing efficiency is a key determinant of a structure’s ability to provide mechanical protection and is defined by the amount of energy that can be absorbed prior to stresses increasing to a level that damages the system to be protected. Here, we explore the energy absorbing efficiency of additively manufactured polymer structures by using a self-driving lab (SDL) to perform >25,000 physical experiments on generalized cylindrical shells. We use a human-SDL collaborative approach where experiments are selected from over trillions of candidates in an 11-dimensional parameter space using Bayesian optimization and then automatically performed while the human team monitors progress to periodically modify aspects of the system. The result of this human-SDL campaign is the discovery of a structure with a 75.2% energy absorbing efficiency and a library of experimental data that reveals transferable principles for designing tough structures.
- 5 April 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (12)
Mechanical Consequences of Oxygen Inhibition in Vat Polymerization
Vat polymerization is a type of additive manufacturing that is used extensively to produce micro‐architected structures for mechanical applications, which brings the mechanical properties of photopolymerized resins into sharp focus. However, it is known that photopolymerization is sensitive to a number of factors, perhaps the most notorious of which is oxygen inhibition. Herein, the degree to which oxygen inhibition influences the macroscopic and microscopic properties of structures made using vat polymerization is explored. This work is motivated by an observation of lattices being >4 times softer in the experiment than predicted by simulation, which is hypothesized to be due to the material at the surface being incompletely cured. This hypothesis is supported by four‐point bending tests in which flexural modulus is found to increase with beam thickness. Nanoindentation and bulk compression studies show that this surface softening is present for three distinct resins. Importantly, it is observed that structures post‐print cured in nitrogen are stiffer than those post‐print cured in air, however, regardless of the post‐print curing environment, printing samples in the presence of oxygen makes them softer than samples photocured in nitrogen. Collectively, these results show the outsized influence of oxygen inhibition on micro‐architected structures realized using vat polymerization.
- 5 April 2023
- Published by Wiley in Advanced Materials Technologies
- Vol. 8 (12)
Mechanical Consequences of Oxygen Inhibition in Vat Polymerization
Vat polymerization is a type of additive manufacturing that is used extensively to produce micro‐architected structures for mechanical applications, which brings the mechanical properties of photopolymerized resins into sharp focus. However, it is known that photopolymerization is sensitive to a number of factors, perhaps the most notorious of which is oxygen inhibition. Herein, the degree to which oxygen inhibition influences the macroscopic and microscopic properties of structures made using vat polymerization is explored. This work is motivated by an observation of lattices being >4 times softer in the experiment than predicted by simulation, which is hypothesized to be due to the material at the surface being incompletely cured. This hypothesis is supported by four‐point bending tests in which flexural modulus is found to increase with beam thickness. Nanoindentation and bulk compression studies show that this surface softening is present for three distinct resins. Importantly, it is observed that structures post‐print cured in nitrogen are stiffer than those post‐print cured in air, however, regardless of the post‐print curing environment, printing samples in the presence of oxygen makes them softer than samples photocured in nitrogen. Collectively, these results show the outsized influence of oxygen inhibition on micro‐architected structures realized using vat polymerization.
- Open Access
- 14 March 2023
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 16 (4) , 1752-1762
3D printed triply periodic minimal surfaces as advanced structured packings for solvent-based CO 2 capture
Advanced structured packing geometries fabricated with 3D printing were used for absorber CO 2 capture with a liquid solvent. Compared to conventional packing, they had greatly enhanced (90–140%) effective surface areas and comparable hydrodynamics.
- 14 March 2023
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 16 (4) , 1752-1762
Open Access3D printed triply periodic minimal surfaces as advanced structured packings for solvent-based CO 2 capture
Advanced structured packing geometries fabricated with 3D printing were used for absorber CO 2 capture with a liquid solvent. Compared to conventional packing, they had greatly enhanced (90–140%) effective surface areas and comparable hydrodynamics.
- Open Access
- 1 April 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (9)
Increasing Throughput in Fused Deposition Modeling by Modulating Bed Temperature
Additive manufacturing (AM) techniques, such as fused deposition modeling (FDM), are able to fabricate physical components from three-dimensional (3D) digital models through the sequential deposition of material onto a print bed in a layer-by-layer fashion. In FDM and many other AM techniques, it is critical that the part adheres to the bed during printing. After printing, however, excessive bed adhesion can lead to part damage or prevent automated part removal. In this work, we validate a novel testing method that quickly and cheaply evaluates bed adhesion without constraints on part geometry. Using this method, we study the effect of bed temperature on the peak removal force for polylactic acid (PLA) parts printed on bare borosilicate glass and polyimide (PI)-coated beds. In addition to validating conventional wisdom that bed adhesion is maximized between 60 and 70 °C (140 and 158 °F), we observe that cooling the bed below 40 °C (104 °F), as is commonly done to facilitate part removal, has minimal additional benefit. Counterintuitively, we find that heating the bed after printing is often a more efficient process for facile part removal. In addition to introducing a general method for measuring and optimizing bed adhesion via bed temperature modulation, these results can be used to accelerate the production and testing of AM components in printer farms and autonomous research systems.
- 1 April 2021
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (9)
Open AccessIncreasing Throughput in Fused Deposition Modeling by Modulating Bed Temperature
Additive manufacturing (AM) techniques, such as fused deposition modeling (FDM), are able to fabricate physical components from three-dimensional (3D) digital models through the sequential deposition of material onto a print bed in a layer-by-layer fashion. In FDM and many other AM techniques, it is critical that the part adheres to the bed during printing. After printing, however, excessive bed adhesion can lead to part damage or prevent automated part removal. In this work, we validate a novel testing method that quickly and cheaply evaluates bed adhesion without constraints on part geometry. Using this method, we study the effect of bed temperature on the peak removal force for polylactic acid (PLA) parts printed on bare borosilicate glass and polyimide (PI)-coated beds. In addition to validating conventional wisdom that bed adhesion is maximized between 60 and 70 °C (140 and 158 °F), we observe that cooling the bed below 40 °C (104 °F), as is commonly done to facilitate part removal, has minimal additional benefit. Counterintuitively, we find that heating the bed after printing is often a more efficient process for facile part removal. In addition to introducing a general method for measuring and optimizing bed adhesion via bed temperature modulation, these results can be used to accelerate the production and testing of AM components in printer farms and autonomous research systems.
- Top Cited PapersOpen Access
- 10 April 2020
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 6 (15) , eaaz1708
A Bayesian experimental autonomous researcher for mechanical design
Automated testing, Bayesian optimization, and additive manufacturing combine for the autonomous design of structures.
- 10 April 2020
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 6 (15) , eaaz1708
Top Cited PapersOpen AccessA Bayesian experimental autonomous researcher for mechanical design
Automated testing, Bayesian optimization, and additive manufacturing combine for the autonomous design of structures.