PTPiotr Tarasiuk

Piotr Tarasiuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Piotr Tarasiuk has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Stress Concentration Factors for Non-Load-Carrying Welded Cruciform Joints Subjected to Tension, Bending, and Shear

    by Krzysztof L. Molski, Piotr Tarasiuk

    This paper deals with the problem of stress concentration at the weld toe of non-load-carrying-type plate cruciform joints under tension, bending, and shear. Theoretical stress concentration factors were derived using the finite element method. Five of the most important geometrical parameters: the thickness of the main plate and the attachments, the weld throat thickness, the weld toe radius, and the weld face inclination angle were treated as independent variables. For each loading mode—tension, bending, and shear—parametric expression of high accuracy was obtained, covering the range used in real structures for cruciform connections. The maximum percentage error was lower than 2.5% as compared to numerical values. The presented solutions proved to be valid for the toe radius ρ tending to zero.


  • Open Access

    Stress Concentration Factors for Welded Plate T-Joints Subjected to Tensile, Bending and Shearing Loads

    by Krzysztof L. Molski, Piotr Tarasiuk

    The paper deals with the problem of stress concentration at the weld toe of a plate T-joint subjected to axial, bending, and shearing loading modes. Theoretical stress concentration factors were obtained from numerical simulations using the finite element method for several thousand geometrical cases, where five of the most important geometrical parameters of the joint were considered to be independent variables. For each loading mode—axial, bending, and shearing—highly accurate closed form parametric expression has been derived with a maximum percentage error lower than 2% with respect to the numerical values. Validity of each approximating formula covers the range of dimensional proportions of welded plate T-joints used in engineering applications. Two limiting cases are also included in the solutions—when the weld toe radius tends to zero and the main plate thickness becomes infinite.


  • Open Access

    Stress concentration at cruciform welded joints under axial and bending loading modes

    by Krzysztof L. Molski, Piotr Tarasiuk, Grzegorz Glinka

    The paper is concerned with the problem of stress concentration in cruciform fillet welded joints subjected to axial and bending load. Extended numerical analyses were carried out with the help of the finite element method. It made it possible to estimate stress concentration factors Kt for a variety of geometrical parameters defining the geometry of cruciform welded joints. It has been found that approximate Kt formulas, available in the literature, have two disadvantages, i.e. an unknown accuracy and small range of application with respect to geometrical parameters defining the weld shape. For these reasons, more general and accurate new formulas for stress concentration factors Kt have been derived. Even though the present approach is applicable to all types of welded joints, the analysis presented below has been conducted for a cruciform joint with the weld flank angle of θ = 45°. Final solutions have been given in the form of polynomial expressions, and they can be easily used in computer-aided design procedures.


  • Open Access

    Stress Concentration Factors for Butt-Welded Plates Subjected to Tensile, Bending and Shearing Loads

    by Krzysztof L. Molski, Piotr Tarasiuk

    This paper deals with the analysis of stress concentration at the weld toe of a Double-V and a Single-V butt-welded joints subjected to tensile, bending and shearing loads. For each geometrical and loading case accurate close form stress concentration factor formula based on more than 3.3 thousand finite element method solutions were obtained. The percentage error of the formulas is lower than 2.5% for a wide range of values of geometrical parameters including weld toe radius, weld width, plate thickness and weld toe angle. The limiting case, in which the weld toe radius tends to zero is also considered. In the cases of shearing loads, a plane model based on thermal analogy was developed. The whole analysis was performed assuming that a circular arc represents the shape of the excess weld metal. Presented solutions may be used in computer aided fatigue assessment of structural elements.