Francisco de Rezende Lopes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Francisco de Rezende Lopes has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Bernadete Ragoni Danziger
Uerj
2 shared publications Fernando A. B. Danziger
Univ Fed Rio de Janeiro, Rio De Janeiro, RJ, Brazil
2 shared publications- Fernando Artur Brasil Danziger
Universidade Federal do Rio de Janeiro
2 shared publications - Marcio de Souza Soares de Almeida
Federal University of Rio de Janeiro (UFRJ) § Graduate School of Engineering, COPPE Rio de Janeiro
2 shared publications - Roney M. Gomes
GroundTech Engenharia , Rio de Janeiro
2 shared publications - Alessander Christopher Morales Kormann
Universidade Federal do Paraná
1 shared publication
Latest Publications
- 30 June 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- p. 1-10
Settlement behaviour of a fill on soft clay assessed by field and laboratory tests
A methodology is presented for evaluating past and future settlements of an area where fill was placed over soft clay some time before the site development – a situation frequently encountered in engineering practice. The proposed approach integrates field and laboratory tests to assess the consolidation stage and estimate settlement development over time. The case study addresses a fill constructed to raise the grade of an area of the campus of the Federal University of Rio de Janeiro, Brazil, which was subsequently developed as a Technological Park. The company leasing the land for a 50-year period required an assessment of the magnitude and rate of settlements expected during the lease term. The testing programme was designed to be cost- and time-effective while still providing results with reasonable accuracy. The consolidation stage was evaluated using in situ pore-pressure measurements obtained with a small-diameter piezometric probe, while the clay consolidation properties were determined from laboratory tests. Established consolidation theories were used to estimate settlement development over time, considering both primary and secondary consolidation.
- 30 June 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- p. 1-10
Settlement behaviour of a fill on soft clay assessed by field and laboratory tests
A methodology is presented for evaluating past and future settlements of an area where fill was placed over soft clay some time before the site development – a situation frequently encountered in engineering practice. The proposed approach integrates field and laboratory tests to assess the consolidation stage and estimate settlement development over time. The case study addresses a fill constructed to raise the grade of an area of the campus of the Federal University of Rio de Janeiro, Brazil, which was subsequently developed as a Technological Park. The company leasing the land for a 50-year period required an assessment of the magnitude and rate of settlements expected during the lease term. The testing programme was designed to be cost- and time-effective while still providing results with reasonable accuracy. The consolidation stage was evaluated using in situ pore-pressure measurements obtained with a small-diameter piezometric probe, while the clay consolidation properties were determined from laboratory tests. Established consolidation theories were used to estimate settlement development over time, considering both primary and secondary consolidation.
- Open Access
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Foundation practice and design in Brazil: a brief review of past and future developments
Brazilian experience in the design and execution of foundations to support superstructures of distinct sorts goes way back to the early colonial period of the XVI century, a few years after the discovery of this land (Katinsky, 1994). Since then, the geotechnical technology related to such constructions has been considerably upgraded and expanded to new system types. The present manuscript aims to briefly review some key aspects of the foundation practice in Brazil during its last decades of development, from the mid-20th century to the present daytime. It does not intend to make a state-of-the-art of the subject but rather highlights the most interesting and relevant points in this evolutionary process of design and construction techniques. Prospective or future foundation technologies will also be envisaged. Given space limitations, it will definitively be narrowed, absent or eventually unfair in some topics or comments. Still, it will serve to highlight the importance of this particular field in the context of the special celebration issue of the 75 years of the Brazilian Soil Mechanics Association. It has been collectively written by some of the most experienced and renowned practitioners and researchers of the Brazilian geotechnical society, despite the absence of so many high-quality others that could equally be present herein. Time and space, unfortunately, have deprived this manuscript of a broader participation and scope.
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Open AccessFoundation practice and design in Brazil: a brief review of past and future developments
Brazilian experience in the design and execution of foundations to support superstructures of distinct sorts goes way back to the early colonial period of the XVI century, a few years after the discovery of this land (Katinsky, 1994). Since then, the geotechnical technology related to such constructions has been considerably upgraded and expanded to new system types. The present manuscript aims to briefly review some key aspects of the foundation practice in Brazil during its last decades of development, from the mid-20th century to the present daytime. It does not intend to make a state-of-the-art of the subject but rather highlights the most interesting and relevant points in this evolutionary process of design and construction techniques. Prospective or future foundation technologies will also be envisaged. Given space limitations, it will definitively be narrowed, absent or eventually unfair in some topics or comments. Still, it will serve to highlight the importance of this particular field in the context of the special celebration issue of the 75 years of the Brazilian Soil Mechanics Association. It has been collectively written by some of the most experienced and renowned practitioners and researchers of the Brazilian geotechnical society, despite the absence of so many high-quality others that could equally be present herein. Time and space, unfortunately, have deprived this manuscript of a broader participation and scope.
- Open Access
- 18 March 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (2)
Finite element prediction of long-term behaviour of a test embankment based on back-analysis of early stages
The paper presents the finite element modeling of a test embankment built at one of the construction sites of the 2016 Olympic Games in Rio de Janeiro, Brazil. The embankment was raised over 6 weeks to a height of 6.7 m, and was monitored during construction and in the following month. The experiment had to end after a month of measurements due to the need to develop the test area. Instrumentation consisted of electric piezometers, settlement plates and inclinometers. The subsoil featured a pack of sedimentary soils, including soft clays. Firstly, field and laboratory tests were evaluated for numerical modelling parameters, and a sensitivity study of the various parameters was carried out. Program PLAXIS was used with the most suitable soil models for the different soil layers. The time-dependent behaviour of the clayey layers followed Terzaghi’s consolidation theory for pore pressure dissipation coupled with a Buisman (1936)-type solution for viscous behaviour. The final analysis used parameters adjusted by back-analysis of measurements in the monitoring period (2.5 months) in a 3D model. This analysis was extended to 50 years, aiming to predict the long-term behaviour of the embankment. Results of the 50-year analysis indicated that after 20 years the excess pore pressures would have practically dissipated, but that the long-term settlement would be 2.5 times greater than that at the end of construction. Furthermore, the ground horizontal displacement would be about 4 times greater than that measured at the end of construction.
- 18 March 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (2)
Open AccessFinite element prediction of long-term behaviour of a test embankment based on back-analysis of early stages
The paper presents the finite element modeling of a test embankment built at one of the construction sites of the 2016 Olympic Games in Rio de Janeiro, Brazil. The embankment was raised over 6 weeks to a height of 6.7 m, and was monitored during construction and in the following month. The experiment had to end after a month of measurements due to the need to develop the test area. Instrumentation consisted of electric piezometers, settlement plates and inclinometers. The subsoil featured a pack of sedimentary soils, including soft clays. Firstly, field and laboratory tests were evaluated for numerical modelling parameters, and a sensitivity study of the various parameters was carried out. Program PLAXIS was used with the most suitable soil models for the different soil layers. The time-dependent behaviour of the clayey layers followed Terzaghi’s consolidation theory for pore pressure dissipation coupled with a Buisman (1936)-type solution for viscous behaviour. The final analysis used parameters adjusted by back-analysis of measurements in the monitoring period (2.5 months) in a 3D model. This analysis was extended to 50 years, aiming to predict the long-term behaviour of the embankment. Results of the 50-year analysis indicated that after 20 years the excess pore pressures would have practically dissipated, but that the long-term settlement would be 2.5 times greater than that at the end of construction. Furthermore, the ground horizontal displacement would be about 4 times greater than that measured at the end of construction.
- Open Access
- 22 December 2023
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 16 (8) , 3270-3283
Inflow and outflow permeability tests in a very soft clay under low stresses
- 22 December 2023
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 16 (8) , 3270-3283
Open AccessInflow and outflow permeability tests in a very soft clay under low stresses
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 19 (5)
Soil-structure interaction with time-dependent behaviour of both concrete and soil
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 19 (5)
Open AccessSoil-structure interaction with time-dependent behaviour of both concrete and soil
- 10 November 2021
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (4) , 1973-1987
On the Use of Random Material in Dam Cores: Case of the Manso Dam, Brazil
- 10 November 2021
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (4) , 1973-1987
On the Use of Random Material in Dam Cores: Case of the Manso Dam, Brazil
- 26 October 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (4) , 1-6
Assessing the undrained strength of very soft clays in the SPT
The log of a SPT in very soft clay may simply indicate a zero blow-count, or present information on the penetration – under self-weight – of the composition (sampler, rods and hammer) as recommended by some standards. The second type of information is often disregarded by design engineers due to the lack of a standard procedure for measuring these penetrations or because the test is regarded as not sensitive enough to give an indication on the undrained shear strength of soft clays. The penetration under the composition’s selfweight, however, can indicate the magnitude of Su, which, along with other more specific and sensitive tests, can help in assessing the spatial distribution of clay consistency in a large deposit. A proposed test procedure and interpretation had been given in an earlier technical note. This note presents an extended formulation and an evaluation of Su via the SPT at a construction site in Rio de Janeiro, including comparisons with results of piezocone and vane tests. The values of Su obtained with the SPT lie between the profiles given by vane tests, corrected by Plasticity Index, and the Critical State Theory, the latter representing a lower bound to the clay strength.
- 26 October 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (4) , 1-6
Assessing the undrained strength of very soft clays in the SPT
The log of a SPT in very soft clay may simply indicate a zero blow-count, or present information on the penetration – under self-weight – of the composition (sampler, rods and hammer) as recommended by some standards. The second type of information is often disregarded by design engineers due to the lack of a standard procedure for measuring these penetrations or because the test is regarded as not sensitive enough to give an indication on the undrained shear strength of soft clays. The penetration under the composition’s selfweight, however, can indicate the magnitude of Su, which, along with other more specific and sensitive tests, can help in assessing the spatial distribution of clay consistency in a large deposit. A proposed test procedure and interpretation had been given in an earlier technical note. This note presents an extended formulation and an evaluation of Su via the SPT at a construction site in Rio de Janeiro, including comparisons with results of piezocone and vane tests. The values of Su obtained with the SPT lie between the profiles given by vane tests, corrected by Plasticity Index, and the Critical State Theory, the latter representing a lower bound to the clay strength.
- 1 July 2021
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 21 (4) , 206-219
Study of plugging of steel H piles, jacked in sand, in a calibration chamber
When predicting the bearing capacity of an H pile, the design engineer is faced with the questions of which perimeter of the pile to consider for lateral resistance, and which base area for tip resistance. These questions derive from the doubt regarding the occurrence of ‘plugging’. The phenomenon, in which soil adheres strongly to the pile, causes failure to occur not at the steel–soil interface but at an enveloping area. There is little experimental data specifically on the plugging of H piles, in which the contribution of shaft and tip loads were properly separated. Different test interpretations by researchers and designers have led to different recommendations for the design of such piles, some considering and others dismissing soil plugging. The research herein described was conducted on instrumented model H piles jacked in fine sand in a large flexible calibration chamber. The results indicate that – even in loose sand – plugging does occur in H piles close to the pile tip and that the tip resistance is an important component of the bearing capacity of such piles.
- 1 July 2021
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 21 (4) , 206-219
Study of plugging of steel H piles, jacked in sand, in a calibration chamber
When predicting the bearing capacity of an H pile, the design engineer is faced with the questions of which perimeter of the pile to consider for lateral resistance, and which base area for tip resistance. These questions derive from the doubt regarding the occurrence of ‘plugging’. The phenomenon, in which soil adheres strongly to the pile, causes failure to occur not at the steel–soil interface but at an enveloping area. There is little experimental data specifically on the plugging of H piles, in which the contribution of shaft and tip loads were properly separated. Different test interpretations by researchers and designers have led to different recommendations for the design of such piles, some considering and others dismissing soil plugging. The research herein described was conducted on instrumented model H piles jacked in fine sand in a large flexible calibration chamber. The results indicate that – even in loose sand – plugging does occur in H piles close to the pile tip and that the tip resistance is an important component of the bearing capacity of such piles.
- 1 April 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (2) , 1-6
Limitations of the Danish driving formula for short piles
Dynamic formulae are a widely used expedient for the control of driven piles to ensure load capacity. These formulae have considerable limitations when used in the prediction of the load capacity on their own, but are very useful in the control of a piling when combined with other tests. This technical note presents an evaluation of the Danish Formula for 54 precast concrete piles, comparing its results with High Strain Dynamic Tests (HSDTs), Static Load Tests (SLTs) and predictions by a semi-empirical static method (Aoki & Velloso, 1975). The data used in the comparison come from three works in the city of Rio de Janeiro, Brazil. All piles were driven with free-fall hammers and in one particular work the piles were relatively short. The predictions of the Danish Formula were evaluated in relation to the pile length/diameter ratio. It was concluded that for short piles - with lengths less than 30 times the diameter - this formula indicates bearing capacities higher than the actual ones. A correction for a safe use of the Danish Formula for short piles is suggested.
- 1 April 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (2) , 1-6
Limitations of the Danish driving formula for short piles
Dynamic formulae are a widely used expedient for the control of driven piles to ensure load capacity. These formulae have considerable limitations when used in the prediction of the load capacity on their own, but are very useful in the control of a piling when combined with other tests. This technical note presents an evaluation of the Danish Formula for 54 precast concrete piles, comparing its results with High Strain Dynamic Tests (HSDTs), Static Load Tests (SLTs) and predictions by a semi-empirical static method (Aoki & Velloso, 1975). The data used in the comparison come from three works in the city of Rio de Janeiro, Brazil. All piles were driven with free-fall hammers and in one particular work the piles were relatively short. The predictions of the Danish Formula were evaluated in relation to the pile length/diameter ratio. It was concluded that for short piles - with lengths less than 30 times the diameter - this formula indicates bearing capacities higher than the actual ones. A correction for a safe use of the Danish Formula for short piles is suggested.
- 31 March 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (1) , 1-10
A proposal for static load tests on piles: the Equilibrium Method
- 31 March 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (1) , 1-10
A proposal for static load tests on piles: the Equilibrium Method