JPJae-Sun Park

Jae-Sun Park

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jae-Sun Park has a total of 146 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Conceptual design of high-dynamic-range spectroscopy for neutral flux measurements in SPARC

    by G. Ronchi, J. Lore, J.-S. Park, A. Rosenthal, M. Reinke, M. Silva Sa, K. Fujii

    We present a conceptual design for High-Dynamic-Range Spectroscopy (HDRS) to measure the penetration of neutrals into the confined plasma of the SPARC tokamak. HDRS detects these penetrating neutrals—hereafter core neutrals—in the far wings of the Balmer-series spectrum, rather than relying on spatial inversion, which is strongly affected by scrape-off layer (SOL) emission. These neutrals undergo charge exchange with high-temperature confined ions, producing significantly greater Doppler broadening than the SOL neutral emission. While this diagnostic concept has been applied to multiple devices, applying it to SPARC will pose unique challenges due to the device’s high density and strong magnetic field. Stark broadening at divertor densities exceeding 1021 m−3 and Zeeman splitting at the ∼12 T magnetic field both broaden the edge emission toward the wavelengths where the core-neutral emission appears, and the metallic first wall can reflect bright divertor light into core-viewing sightlines. To quantify these effects, we developed a framework that couples plasma backgrounds from the scrape-off layer plasma simulation-ITER code, OpenADAS atomic data, and Cherab/Raysect ray tracing and used it to produce line-integrated spectra for illustrative chords and derive preliminary spectrometer requirements. The synthetic spectra identify a Dα core-neutral shoulder visible around 1–3 nm away from the line center, embedded in the Stark tail of the cold edge emission; Dγ, by contrast, remains Stark-dominated and provides an independent constraint on the edge electron density. The resulting spectrometer concept targets a resolving power of 20 000–40 000, a 7.5–15 nm bandwidth, and a 105–106:1 dynamic range.

  • Open Access

    Radiative divertor detachment and impurity transport with nitrogen and neon seeding in KSTAR H-mode plasmas

    by Junghoo Hwang, H.H. Lee, Richard A Pitts, Andrei Pshenov, Jae-Sun Park, Yoon Seong Han, June-Woo Juhn, Matthias Bernert, Jun Gyo Gyo Bak, Suk-Ho Hong, et al.

    Achieving core-edge compatible divertor detachment is a critical requirement for stable operation in future fusion devices. This study compares nitrogen and neon seeding in KSTAR H-mode plasmas with carbon walls, combining experiments and SOLPS-ITER modelling to evaluate their radiative dissipation and core-edge compatibility. Experimentally, N seeding achieved stronger divertor detachment, with larger reductions in target particle and heat fluxes, a higher divertor radiation fraction, and a lower core radiation fraction than Ne. In contrast, Ne seeding triggered a significant rise in core radiation followed by H-L back transitions, limiting the maximum total radiated power fraction to roughly half that of N. SOLPS-ITER simulations reproduced the experimental trends and revealed that the better core-edge compatibility of N arises from its higher divertor retention in addition to its higher cooling factor. The relative positions of the stagnation points of impurity poloidal velocity and ionization sources did not explain the different divertor compression. Instead, in the present modelling, the higher impurity parallel particle flux, resulting from the higher parallel impurity velocity, explains the stronger nitrogen impurity compression in the divertor region. The parallel temperature distribution with N was more favourable for achieving higher impurity parallel velocity than with Ne, because the impurity velocity is governed by modifications of the main ion flow due to friction and thermal forces, both of which strongly depend on the temperature. Ultimately, this behaviour is attributed to the strongly divertor-localized radiation of N. These results demonstrate that N is more effective than Ne in achieving radiative divertor detachment while maintaining low core contamination in KSTAR, consistent with observations in other present tokamaks.

  • Open Access

    Autoregressive long-horizon prediction of plasma edge dynamics *

    by Hunor Csala, Sebastian De Pascuale, Paul Laiu, Jeremy Lore, Jae-Sun Park, Pei Zhang

    Accurate modeling of scrape-off layer (SOL) and divertor-edge dynamics is vital for designing plasma-facing components in fusion devices. High-fidelity edge fluid/neutral codes such as SOLPS-ITER capture SOL physics with high accuracy, but their computational cost limits broad parameter scans and long transient studies. We present transformer-based, autoregressive surrogates for efficient prediction of 2D, time-dependent plasma edge state fields. Trained on SOLPS-ITER spatiotemporal data for the KSTAR tokamak, the surrogates forecast electron temperature, electron density, and radiated power over extended horizons. We evaluate model variants trained with increasing autoregressive horizons (1–100 steps) on short- and long-horizon prediction tasks. Longer-horizon training systematically improves rollout stability and mitigates error accumulation, enabling stable predictions over hundreds to thousands of steps and reproducing key dynamical features such as the motion of high-radiation regions. Measured end-to-end wall-clock times show the surrogate is orders of magnitude faster than SOLPS-ITER, enabling rapid parameter exploration. Prediction accuracy degrades when the surrogate enters physical regimes not represented in the training dataset, motivating future work on data enrichment and physics-informed constraints. Overall, this approach provides a fast, accurate surrogate for computationally intensive plasma edge simulations, supporting rapid scenario exploration, control-oriented studies, and progress toward real-time applications in fusion devices.

  • Open Access

    Radiation-front position control with scenario adjustments during the first tungsten divertor operation on KSTAR

    by CheolSik Byun, Seungtae Oh, SangKyeun Kim, Boseong Kim, Yoon Seong Han, Sang-Hee Hahn, H.H. Lee, Azarakhsh Jalalvand, Youngho Lee, Junghoo Hwang, et al.

    This study reports the first experimental demonstration of a radiation front-based detachment control system during the initial tungsten divertor campaign in KSTAR. The system employs real-time infrared video bolometry with tomographic reconstruction to track the inboard radiation-front position, which served as a feedback variable for impurity seeding. In a baseline scenario without pre-D2 fueling, tungsten accumulation triggered core radiation surges and repetitive H–L back transitions. In contrast, with pre-D2 fueling, detachment was stabilized by maintaining higher ELM frequency, suppressing core tungsten buildup, and reducing sputtering, thereby enabling sustained feedback control. The suitability of the inboard front position as a detachment control metric was confirmed by its correlation with the degree of detachment: with D2 fueling the relation exhibited a broad hysteresis loop characteristic of momentum-loss–dominated detachment, whereas with N2 fueling, it became narrow and nearly vertical, consistent with radiation-loss–dominated pinning. These results provide a proof-of-principle for radiation-front–based detachment control, demonstrating its viability as a control approach. At the same time, these results clarify that the detachment outcomes were further conditioned by impurity transport characteristics of tungsten divertor operation in KSTAR, providing guidance for future scenario optimization and controller development in tungsten devices.


  • Open Access

    Towards self-consistent integrated modeling of the tokamak pedestal, scrape-off layer, and divertor using SOLPS-ITER and EPED

    by Robert S Wilcox, John M Canik, J M Park, Philip B Snyder, Morgan W Shafer, Sebastian De Pascuale, Davis Easley, Anthony W Leonard, Jeremy D Lore, Adam G McLean, et al.

    A predictive, self-consistent integrated model of the tokamak edge plasma and neutral system has been developed and validated against experimental data from DIII-D, spanning from the divertor target and scrape-off layer to the top of the pedestal. The model uses the SOLPS-ITER fluid boundary plasma and neutral code to constrain the EPED prediction of the pedestal height and width by taking the separatrix temperature and density calculated from SOLPS as inputs to EPED. An empirical proxy function based on data from a subset of these discharges is then used to infer the ratio of density at the pedestal top to that at the separatrix based on the electron temperature at the divertor target. This allows the density at the top of the pedestal to be provided to EPED as well, so that knowledge of this quantity is no longer required a priori, while SOLPS radial transport coefficients are needed instead. The gas puff rate provided to SOLPS is then a primary model input for this forward model coupling (along with radial transport coefficients, which are kept fixed through each scan in this study). Comparisons with measurements from DIII-D density scans through a range of target conditions find significant pedestal pressure degradation as the density is increased towards detachment in three different divertor configurations, consistent with the experimental data in these ballooning-limited pedestal regimes.


  • Open Access

    Autoregressive long-horizon prediction of plasma edge dynamics

    by Hunor Csala, Sebastian De Pascuale, Paul Laiu, Jeremy Lore, Jae-Sun Park, Pei Zhang

    Accurate modeling of scrape-off layer (SOL) and divertor-edge dynamics is vital for designing plasma-facing components in fusion devices. High-fidelity edge fluid/neutral codes such as SOLPS-ITER capture SOL physics with high accuracy, but their computational cost limits broad parameter scans and long transient studies. We present transformer-based, autoregressive surrogates for efficient prediction of 2D, time-dependent plasma edge state fields. Trained on SOLPS-ITER spatiotemporal data, the surrogates forecast electron temperature, electron density, and radiated power over extended horizons. We evaluate model variants trained with increasing autoregressive horizons (1-100 steps) on short- and long-horizon prediction tasks. Longer-horizon training systematically improves rollout stability and mitigates error accumulation, enabling stable predictions over hundreds to thousands of steps and reproducing key dynamical features such as the motion of high-radiation regions. Measured end-to-end wall-clock times show the surrogate is orders of magnitude faster than SOLPS-ITER, enabling rapid parameter exploration. Prediction accuracy degrades when the surrogate enters physical regimes not represented in the training dataset, motivating future work on data enrichment and physics-informed constraints. Overall, this approach provides a fast, accurate surrogate for computationally intensive plasma edge simulations, supporting rapid scenario exploration, control-oriented studies, and progress toward real-time applications in fusion devices.

  • Open Access

    SOLEDGE3X full vessel plasma boundary simulations of ITER non-active phase plasmas

    by N. Rivals, P. Tamain, Y. Marandet, X. Bonnin, J.-S. Park, H. Bufferand, R.A. Pitts, G. Falchetto, H. Yang, G. Ciraolo

    The onset of detachment in the ITER machine is analyzed in this work through the help of 2D-axisymmetric boundary plasma simulations with the SOLEDGE3X-EIRENE code, which features a numerical domain for the plasma solver extending up to the first wall. The plasma boundary is computed in scenarios from the first non-active phase of ITER, in pure H and at 20 MW. This set of simulations is used in two aspects: first, to study the plasma detachment in the divertor, and second, the plasma conditions, fluxes, and beryllium erosion at the first wall. Here, the code results are also compared to those obtained with the well-established SOLPS-ITER code, which includes a plasma numerical domain only covering the main SOL. Results show an increase in the SOL width λ q with increasing density, and a detailed analysis is carried out, for the first time, on each of the different plasma-neutral interactions in the code’s physics model in EIRENE. The gross beryllium erosion rates of first wall panels are estimated from 2D simulations, with the aim of assessing their sensitivity to two parameters: the divertor density regime, and the presence of density shoulders in the far-SOL formed by enhanced perpendicular transport at this location. The erosion contributions from neutrals and ions are considered in each case, and the charge-exchange atoms fluxes and energy distributions are provided, highlighting the two atom populations (cold and charge-exchange).


  • Open Access

    Evaluation of SPARC divertor conditions in H-mode operation using SOLPS-ITER

    by Jeremy D. Lore, Jae-Sun Park, Thomas Eich, Adam Q. Kuang, Matthew L. Reinke, Sebastian De Pascuale, Bart Lomanowski, Alex Creely, John M. Canik

    The predicted divertor conditions for the SPARC tokamak are calculated using SOLPS-ITER for a range of scrape-off-layer (SOL) heat flux widths λ q , input powers, and particle fueling locations. Under H-mode scenario conditions with an upstream separatrix density of 1 × 10 20 m−3, the most conservative range of λ q extrapolations ( ≈ 0.15 mm) results in extremely high unmitigated particle and energy fluxes to the divertor, both under full field (12.2 T) and power ( P SOL = 29 MW) conditions, and 2/3 field with P SOL = 10 MW. Increasing the cross-field SOL diffusivities by 2–10× reduces the magnitude of the mitigation challenge, however strategies such as impurity seeding or strike-point-sweeping will likely still be required. A combination of steady-state and time-dependent SOLPS-ITER simulations are used to map out phase space diagrams of upstream and divertor conditions. The simulations include parallel currents but neglect cross-field drifts. At low upstream density the inner and outer divertor conditions are highly asymmetric, with a large temperature difference and significant heat fluxes driven by parallel currents. The solution has sharp bifurcations with a region of hysteresis, depending on whether the initial state is at a low or high density. This behavior is observed even when the fueling location, cross-field diffusivity, and impurity level is changed, although the density window with asymmetry is reduced with increasing diffusivity. The addition of neon impurity seeding reduces the divertor heat fluxes, but also causes a drop in the upstream electron density with fixed particle throughput. This drop can be counteracted by increased main ion throughput, however too much neon results in a back transition into the asymmetric divertor regimes suggesting a need for control of both main ion and impurity seeding levels to achieve a desired divertor state.


  • Open Access

    Conceptual design of a Doppler spectrometer for 102 m/s cross-field flows in tokamak divertors

    by K. Fujii, R. Sano, T. Nakano, G. Ronchi, J.-S. Park, J. D. Lore, M. Shafer, T. M. Biewer

    The cross-field transport in the scrape-off-layers (SOLs) and divertors in tokamaks is of a similar size to the poloidal component of the parallel flow, thereby significantly impacting the plasma transport there. However, its direct observation has been challenging because the drift velocity (102–103 m/s) is significantly below the detection limit of conventional diagnostics. To realize cross-field ion flow measurement, a variety of systematic uncertainties in the system must be narrowed down. Here, we develop a conceptual design of the Doppler spectrometry that enables us to measure the impurity flows with 102-m/s accuracy based on an in situ wavelength-calibration technique developed in the astrophysics field, the iodine-cell method. We discuss its properties and applicability. In particular, the scaling relation between wavelength accuracy and various spectroscopic parameters is newly presented, which suggests the high importance of the wavelength resolution of the system. Based on transport simulations for the JT-60SA divertor, the feasibility of the system is assessed.

  • Open Access

    Full time-dependent SOLPS-ITER simulation of the SPARC tokamak: actuator design for particle and divertor condition control *

    by Jae-Sun Park, Jeremy D. Lore, Matthew Reinke, Adam Q. Kuang, Sebastian De Pascuale, Alex Creely

    This paper presents the application of full time-dependent SOLPS-ITER simulations for actuator design in the SPARC tokamak. This study employs both the EIRENE module, a neutral solver, and the B2.5 plasma module in a time-dependent mode. This is in contrast to most SOLPS simulations, which focus on steady-state solutions, where the neutral distribution is evolved without any time limit or for a time step of 1 ⋅ 10 − 3 second, which is several orders of magnitude larger than the fluid plasma time step. The time-dependent EIRENE was tested with a fixed B2.5 background and compared with a simple conductance based model in a simplified pump chamber geometry. This comparison aimed to verify the reliability of the neutral relaxation timescale derived from the time-dependent EIRENE. Subsequently, a full time-dependent simulation was performed in a realistic geometry, with the Monte-Carlo neutral time step synchronized with the plasma fluid time step. The numerical setup of the code, including relative time steps and the size of the census data used to store Monte-Carlo particle information is considered. The full-time dependent simulations are then applied to inform the design of the SPARC louver structure, which affects divertor plasma parameters by regulating the neutral conductance from the divertor to the pump. The response of the plasma and neutral parameters was captured on a timescale that enables the design of the actuator to consider time-dependent control capability. It was found that changing the louver opacity has an equivalent effect as varying the gas throughput via puff actuation. Therefore, equivalent divertor plasma conditions can be obtained from both actuators, while the neutral pressure distribution in the pump and divertor differs for each actuator.