Yuki Kanda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuki Kanda has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Atsuki Komiya
Tohoku University
13 shared publications - Junnosuke Okajima
Institute of Fluid Science, Tohoku University
9 shared publications Shigenao Maruyama
National Institute of Technology, Hachinohe College 3 , Tamonoki, Hachinohe 039-1192, Japan
8 shared publications- Lin Chen
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
5 shared publications - Eita Shoji
Department of Mechanical Systems Engineering, Graduate School of Engineering, Tohoku University, 6-6-01 Aramaki, Aoba-ku, Sendai, Miyagi 980-8579, Japan
3 shared publications Hikaru Yamada
3 shared publications
Latest Publications
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Effects of morphology of trapped CO2 bubbles on dissolution mass transfer in porous media: A pore-scale simulation
Understanding CO2 dissolution in porous media is crucial for assessing the efficiency and safety of geological carbon storage. While empirical power-law correlations can capture the effect of flow velocity on mass transfer, they often overlook the influence of bubble morphology. In this study, we employ pore-scale direct numerical simulations to investigate the dissolution process of trapped CO2 bubbles in porous media with two typical configurations: singlets and clusters. Key transport parameters, including interfacial area, flow field distribution, local Péclet number, and concentration distribution, were analyzed under different flow rates and saturations to evaluate performance. Results reveal a non-monotonic trend in mass transfer coefficients for singlet bubbles with increasing saturation—initially rising and then declining. At low saturations (15%), the development of extensive stagnant flow regions suppresses local concentration gradients, resulting in diffusion-dominated transport and reduced overall mass transfer rate. A comparison between bubble morphologies shows that singlet bubbles dissolve significantly faster than clusters, not only due to greater interfacial area but also higher overall mass transfer coefficients. Moreover, for singlet bubbles, a consistent power-law relationship between Sherwood and Reynolds numbers is observed across all conditions, with the scaling exponent strongly depending the gas saturation and bubble configuration. These findings emphasize the critical role of bubble morphology in CO2 dissolution and provide quantitative data for improving continuum-scale reservoir models.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Effects of morphology of trapped CO2 bubbles on dissolution mass transfer in porous media: A pore-scale simulation
Understanding CO2 dissolution in porous media is crucial for assessing the efficiency and safety of geological carbon storage. While empirical power-law correlations can capture the effect of flow velocity on mass transfer, they often overlook the influence of bubble morphology. In this study, we employ pore-scale direct numerical simulations to investigate the dissolution process of trapped CO2 bubbles in porous media with two typical configurations: singlets and clusters. Key transport parameters, including interfacial area, flow field distribution, local Péclet number, and concentration distribution, were analyzed under different flow rates and saturations to evaluate performance. Results reveal a non-monotonic trend in mass transfer coefficients for singlet bubbles with increasing saturation—initially rising and then declining. At low saturations (15%), the development of extensive stagnant flow regions suppresses local concentration gradients, resulting in diffusion-dominated transport and reduced overall mass transfer rate. A comparison between bubble morphologies shows that singlet bubbles dissolve significantly faster than clusters, not only due to greater interfacial area but also higher overall mass transfer coefficients. Moreover, for singlet bubbles, a consistent power-law relationship between Sherwood and Reynolds numbers is observed across all conditions, with the scaling exponent strongly depending the gas saturation and bubble configuration. These findings emphasize the critical role of bubble morphology in CO2 dissolution and provide quantitative data for improving continuum-scale reservoir models.
- 20 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 256
Modeling of scattering coefficient for biological tissues exposed to near-infrared laser irradiation
- 20 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 256
Modeling of scattering coefficient for biological tissues exposed to near-infrared laser irradiation
- 1 March 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (3) , 036102
Asymptotic analysis of boundary thermal-wave process near the liquid–gas critical point
The role of near-critical properties has been considered as key point for the understanding of transient origins of fluid transport physics, especially in the boundary layers. Asymptotic model analysis with modified governing equations of the fluid has been utilized to study the characters of near-critical fluids subjected to a temperature pulse, under different boundary conditions: thermostatic or insulated. The asymptotic solutions show that the boundary layers are mainly governed by the diffusion effect (sensitive to spatial gradients) while exhibiting the wave character in bulk. When a small thermal pulse is imposed at the boundary, wave process with a magnitude about 0.05 mK is seen generated. The wave propagates in the one-dimensional cell, reflecting a quick re-distribution of parameters in acoustic timescale. Transient temperature and pressure results show that as the fluids flow across the boundary layers to the bulk, acoustic wave process is associated with that of the specific energy transportation process.
- 1 March 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (3) , 036102
Asymptotic analysis of boundary thermal-wave process near the liquid–gas critical point
The role of near-critical properties has been considered as key point for the understanding of transient origins of fluid transport physics, especially in the boundary layers. Asymptotic model analysis with modified governing equations of the fluid has been utilized to study the characters of near-critical fluids subjected to a temperature pulse, under different boundary conditions: thermostatic or insulated. The asymptotic solutions show that the boundary layers are mainly governed by the diffusion effect (sensitive to spatial gradients) while exhibiting the wave character in bulk. When a small thermal pulse is imposed at the boundary, wave process with a magnitude about 0.05 mK is seen generated. The wave propagates in the one-dimensional cell, reflecting a quick re-distribution of parameters in acoustic timescale. Transient temperature and pressure results show that as the fluids flow across the boundary layers to the bulk, acoustic wave process is associated with that of the specific energy transportation process.
- 17 June 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (6) , L061501
Resonance-driven heat transfer enhancement in a natural convection boundary layer perturbed by a moderate impinging jet
We report a resonance-driven convective heat transfer enhancement downstream of a natural convection boundary layer that is perturbed by a moderate impinging jet. Flow resonance is experimentally and numerically confirmed between the boundary layer and a periodic flow driven by the unbalance of jet momentum and buoyancy. When the oscillation frequency in the impinging region is a submultiple of the characteristic frequency of natural convection, downstream heat transfer enhancement from the baseline of natural convection exceeds 40%. In contrast, further increasing the jet momentum fourfold yields . The results support the development of efficient heat transfer enhancement methods.- 17 June 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (6) , L061501
Resonance-driven heat transfer enhancement in a natural convection boundary layer perturbed by a moderate impinging jet
We report a resonance-driven convective heat transfer enhancement downstream of a natural convection boundary layer that is perturbed by a moderate impinging jet. Flow resonance is experimentally and numerically confirmed between the boundary layer and a periodic flow driven by the unbalance of jet momentum and buoyancy. When the oscillation frequency in the impinging region is a submultiple of the characteristic frequency of natural convection, downstream heat transfer enhancement from the baseline of natural convection exceeds 40%. In contrast, further increasing the jet momentum fourfold yields . The results support the development of efficient heat transfer enhancement methods.- 1 April 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (4) , 047105
Visualization of methane hydrate decomposition interface and analyses of decomposition rate and interfacial configuration
Composed of methane gas and cage-like water molecules, methane hydrate is expected to have innovative engineering applications, such as gas transportation. In this study, a methane hydrate decomposition interface is visualized qualitatively, and the decomposition rate is discussed. To clarify the decomposition mechanism, consideration is given to the dynamic decomposition interface and the variation of the decomposition rate. In the present experiment, methane hydrate is formed around a water droplet and decomposed by depressurization in the gas phase, the dynamic variation of the decomposition interface is observed precisely using a high-resolution camera, and three different depressurization conditions are used to confirm the interfacial change. It is found that the decomposition rate and dynamic shape change of the decomposition interface depend on the difference between the equilibrium pressure and that of the gas phase. In addition, the decomposition time is discussed using the decomposition model, and it is estimated that the present experimental decomposition rate corresponds to a lower activation energy for decomposition compared with that of the model by other authors. It is assumed that the decomposition proceeds under nearly reaction-limited conditions. Additionally, the interfacial deformation and collapse are observed in the case of pressure reduction near the equilibrium pressure, and validation is provided by a numerical simulation considering the heat and mass transfer near the interface. The numerical results suggest that the decomposition is affected by the interfacial configuration and the nearby temperature and concentration distributions.
- 1 April 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (4) , 047105
Visualization of methane hydrate decomposition interface and analyses of decomposition rate and interfacial configuration
Composed of methane gas and cage-like water molecules, methane hydrate is expected to have innovative engineering applications, such as gas transportation. In this study, a methane hydrate decomposition interface is visualized qualitatively, and the decomposition rate is discussed. To clarify the decomposition mechanism, consideration is given to the dynamic decomposition interface and the variation of the decomposition rate. In the present experiment, methane hydrate is formed around a water droplet and decomposed by depressurization in the gas phase, the dynamic variation of the decomposition interface is observed precisely using a high-resolution camera, and three different depressurization conditions are used to confirm the interfacial change. It is found that the decomposition rate and dynamic shape change of the decomposition interface depend on the difference between the equilibrium pressure and that of the gas phase. In addition, the decomposition time is discussed using the decomposition model, and it is estimated that the present experimental decomposition rate corresponds to a lower activation energy for decomposition compared with that of the model by other authors. It is assumed that the decomposition proceeds under nearly reaction-limited conditions. Additionally, the interfacial deformation and collapse are observed in the case of pressure reduction near the equilibrium pressure, and validation is provided by a numerical simulation considering the heat and mass transfer near the interface. The numerical results suggest that the decomposition is affected by the interfacial configuration and the nearby temperature and concentration distributions.
- 29 October 2018
- Published by Science China Press., Co. Ltd. in Chinese Science Bulletin
- Vol. 63 (31) , 3241-3250
Oceanic methane hydrate utilization system design and reservoir scale numerical modeling
In recent years, the exploration and utilization of methane hydrate from permafrost and off-coast regions has become a very hot topic. Aiming at its potential as a vast energy resources in future use, the current study is focused on the low emission extraction and utilization system for oceanic methane hydrate and its economic and technological feasibility. In this study, recent real extraction tests in both China and Japan in 2017 are firstly discussed and compared, where the challenges in production period and production rate are explained. In those tests, depressurization method is used to dissociate the methane hydrate for gas production form the unconsolidated reservoir layers below the seabed. Based on the conditions of Japan, a systematic utilization system is proposed for oceanic methane hydratewhich is consisted of extraction system, power generation system, Carbon Capture and Sequestration (CCS) system and hot fluid injection system. Vertical well systems are adopted in this design and the strategic warming up process is used before depressurization extraction, so as to obtain optimal production rate of methane gas. The inclusion of CCS makes it possible to utilize methane hydrate with very low carbon emission. It is estimated that the electricity price obtained by this system can be comparable with the current civil electric price in Japan if the production rate is around 1.0×105 m3/d. Also in this study, the real extraction scenarios and possible strategies of Nankai Trough in Japan and Shenhu Area in China are re-visited and discussed by numerical models. It is found that the only depressurization or thermal stimulation method have the problems of wellbore deformation, pressure problem and energy efficiency problems, while combined strategic modes show the possibility of long-term continuous production. For the basic dissociation parameter analysis, the conditions near the equilibrium curve show higher production rate, which is due to higher initial reservoir temperature. Such results indicate the importance of heat supply inside the reservoir layer as the methane hydrate dissociation is endothermic. It is shown that with the increase of reservoir pressure, such temperature effects become more critical as the optimal initial temperature increases according to equilibrium curve. This results support the system design with strategic warming-up process in a sister well during methane hydrate extraction. In addition, the effects of reservoir layer thermal management, hot reservoir fluid flow effects on the dissociation behaviors are analyzed in this study. For vertical well analysis, the production rates under different permeability parameters show the same trend with real production, which in turn help confirm the in-lab permeability tests. Horizontal well simulation show the importance of overburden and under burden. If the confining layers are less permeable, the production rate becomes higher due to the limited intrusive water flow from the confining layers. In sum, this study summarized the advantages and disadvantages of oceanic methane hydrate extraction/utilization methods and put forward a low-carbon emission system. It is hoped that this study will contribute to the future development of both production prediction and real extraction tests.
- 29 October 2018
- Published by Science China Press., Co. Ltd. in Chinese Science Bulletin
- Vol. 63 (31) , 3241-3250
Oceanic methane hydrate utilization system design and reservoir scale numerical modeling
In recent years, the exploration and utilization of methane hydrate from permafrost and off-coast regions has become a very hot topic. Aiming at its potential as a vast energy resources in future use, the current study is focused on the low emission extraction and utilization system for oceanic methane hydrate and its economic and technological feasibility. In this study, recent real extraction tests in both China and Japan in 2017 are firstly discussed and compared, where the challenges in production period and production rate are explained. In those tests, depressurization method is used to dissociate the methane hydrate for gas production form the unconsolidated reservoir layers below the seabed. Based on the conditions of Japan, a systematic utilization system is proposed for oceanic methane hydratewhich is consisted of extraction system, power generation system, Carbon Capture and Sequestration (CCS) system and hot fluid injection system. Vertical well systems are adopted in this design and the strategic warming up process is used before depressurization extraction, so as to obtain optimal production rate of methane gas. The inclusion of CCS makes it possible to utilize methane hydrate with very low carbon emission. It is estimated that the electricity price obtained by this system can be comparable with the current civil electric price in Japan if the production rate is around 1.0×105 m3/d. Also in this study, the real extraction scenarios and possible strategies of Nankai Trough in Japan and Shenhu Area in China are re-visited and discussed by numerical models. It is found that the only depressurization or thermal stimulation method have the problems of wellbore deformation, pressure problem and energy efficiency problems, while combined strategic modes show the possibility of long-term continuous production. For the basic dissociation parameter analysis, the conditions near the equilibrium curve show higher production rate, which is due to higher initial reservoir temperature. Such results indicate the importance of heat supply inside the reservoir layer as the methane hydrate dissociation is endothermic. It is shown that with the increase of reservoir pressure, such temperature effects become more critical as the optimal initial temperature increases according to equilibrium curve. This results support the system design with strategic warming-up process in a sister well during methane hydrate extraction. In addition, the effects of reservoir layer thermal management, hot reservoir fluid flow effects on the dissociation behaviors are analyzed in this study. For vertical well analysis, the production rates under different permeability parameters show the same trend with real production, which in turn help confirm the in-lab permeability tests. Horizontal well simulation show the importance of overburden and under burden. If the confining layers are less permeable, the production rate becomes higher due to the limited intrusive water flow from the confining layers. In sum, this study summarized the advantages and disadvantages of oceanic methane hydrate extraction/utilization methods and put forward a low-carbon emission system. It is hoped that this study will contribute to the future development of both production prediction and real extraction tests.
- 1 January 2018
- Published by Begell House Inc. Publishers
VISUALIZATION OF HEAT AND MASS TRANSFER NEAR THE FORMATION AND DISSOCIATION INTERFACE OF CO2 HYDRATE WITH HIGH–SPEED PHASE–SHIFTING INTERFEROMETER
In this study, transient heat and mass transfer during CO2 hydrate formation and dissociation processes is visualized quantitatively by a high-speed phase-shifting interferometer. CO2 hydrate has an attractive potential to be used as CO2 capture and storage (CCS) and secondary refrigerant due to the enormous dissociation enthalpy. However, gas hydrate dissociation mechanism including CO2 hydrate has not been well understood due to the complex phase-change and heat and mass transportation at the reaction interface. This study aims to measure CO2 hydrate formation and dissociation process with transient heat and mass transfer in the vicinity of solid–gas interface quantitatively. CO2 hydrate is formed on a liquid film with the pressurized CO2 gas. The experiment is conducted in the temperature controlled pressure vessel with two quartz windows. The dissociation is caused by decreasing the pressure. The transient density distribution in the vicinity of solid–gas interface during the formation and dissociation is measured quantitatively by using the high-speed phase-shifting interferometer. The simulation is performed with the two-dimensional (2D) diffusive equation in the gas phases to validate experimental results. Finally, the CO2 mass concentration and the effect of heat transfer in the gas phase on the formation and dissociation are discussed.
- 1 January 2018
- Published by Begell House Inc. Publishers
VISUALIZATION OF HEAT AND MASS TRANSFER NEAR THE FORMATION AND DISSOCIATION INTERFACE OF CO2 HYDRATE WITH HIGH–SPEED PHASE–SHIFTING INTERFEROMETER
In this study, transient heat and mass transfer during CO2 hydrate formation and dissociation processes is visualized quantitatively by a high-speed phase-shifting interferometer. CO2 hydrate has an attractive potential to be used as CO2 capture and storage (CCS) and secondary refrigerant due to the enormous dissociation enthalpy. However, gas hydrate dissociation mechanism including CO2 hydrate has not been well understood due to the complex phase-change and heat and mass transportation at the reaction interface. This study aims to measure CO2 hydrate formation and dissociation process with transient heat and mass transfer in the vicinity of solid–gas interface quantitatively. CO2 hydrate is formed on a liquid film with the pressurized CO2 gas. The experiment is conducted in the temperature controlled pressure vessel with two quartz windows. The dissociation is caused by decreasing the pressure. The transient density distribution in the vicinity of solid–gas interface during the formation and dissociation is measured quantitatively by using the high-speed phase-shifting interferometer. The simulation is performed with the two-dimensional (2D) diffusive equation in the gas phases to validate experimental results. Finally, the CO2 mass concentration and the effect of heat transfer in the gas phase on the formation and dissociation are discussed.
- 1 December 2017
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 89, 57-63
Measurement of transient heat transfer in vicinity of gas–liquid interface using high-speed phase-shifting interferometer
- 1 December 2017
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 89, 57-63
Measurement of transient heat transfer in vicinity of gas–liquid interface using high-speed phase-shifting interferometer