Meryem Polat Gonullu
Meryem Polat Gonullu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Damla Dilara Çakil
Metallurgical and Materials Engineering
3 shared publications - Cemil Çetinkaya
Gazi Üniversitesi
2 shared publications - Burak Nalcaci
Gazi University
1 shared publication Cemil Cetinkaya
1 shared publication- Hakan Ates
Gazi Üniversitesi
1 shared publication - Halil İbRahim Efkere
Photonics Application and Research Center, Gazi University, Ankara, Türkiye
1 shared publication
Latest Publications
- Open Access
- 12 October 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (5) , 1535-1543
Effects of Heat Treatment Time on Properties of 1% Fe-Doped ZnO Films Fabricated by Ultrasonic Spray Pyrolysis
In this study, 1% Fe-doped ZnO thin films were deposited using Ultrasonic Spray Pyrolysis (USP) to examine their structural, morphological, and photocatalytic properties. Heat treatment was applied to 1% Fe-doped ZnO thin films produced with USP at 500 ºC for different times (1, 3, and 5 hours). The results of the samples heat-treated for different times were compared with the as-deposited sample in terms of morphological, structural properties, and photocatalytic degradation efficiency. It was observed that the ZnO thin films with a heat treatment time of 3 hours had more distinct crystal structures, and their surface morphologies were more regular and homogeneous. When the photocatalytic behaviors were examined, it was determined that the degradation efficiency of the samples heat-treated for 3 hours was better than the other samples. In conclusion, this study shows that the heat treatment time of 1% Fe-doped ZnO thin films deposited by USP significantly affects the films' structural, morphological properties, and photocatalytic activity behaviors. These results emphasize that the heat treatment time of 3 hours should be preferred and guide future research in thin film production and photocatalytic applications.
- 12 October 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (5) , 1535-1543
Open AccessEffects of Heat Treatment Time on Properties of 1% Fe-Doped ZnO Films Fabricated by Ultrasonic Spray Pyrolysis
In this study, 1% Fe-doped ZnO thin films were deposited using Ultrasonic Spray Pyrolysis (USP) to examine their structural, morphological, and photocatalytic properties. Heat treatment was applied to 1% Fe-doped ZnO thin films produced with USP at 500 ºC for different times (1, 3, and 5 hours). The results of the samples heat-treated for different times were compared with the as-deposited sample in terms of morphological, structural properties, and photocatalytic degradation efficiency. It was observed that the ZnO thin films with a heat treatment time of 3 hours had more distinct crystal structures, and their surface morphologies were more regular and homogeneous. When the photocatalytic behaviors were examined, it was determined that the degradation efficiency of the samples heat-treated for 3 hours was better than the other samples. In conclusion, this study shows that the heat treatment time of 1% Fe-doped ZnO thin films deposited by USP significantly affects the films' structural, morphological properties, and photocatalytic activity behaviors. These results emphasize that the heat treatment time of 3 hours should be preferred and guide future research in thin film production and photocatalytic applications.
- 16 February 2024
- Published by Elsevier in Thin Solid Films
- Vol. 793
Influence of thermal treatment and Fe doping on ZnO films by ultrasonic spray pyrolysis
- 16 February 2024
- Published by Elsevier in Thin Solid Films
- Vol. 793
Influence of thermal treatment and Fe doping on ZnO films by ultrasonic spray pyrolysis
- Open Access
- 30 December 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (4) , 1026-1036
The Attitude of ZnO/Al2O3 Film Produced by Ultrasonic Spray Pyrolysis Under Thermal Annealing
Impact of annealing on structural, morphological, elemental, and optical properties of bilayer ZnO/Al2O3 film has been investigated. Bilayer film has been deposited on microscope slides by ultrasonic spray pyrolysis method at 350°C substrate temperature. Then, this film has been annealed at 400°C, 500°C, and 600°C under atmospheric conditions, respectively. Structural analyses have been revealed that bilayer films have polycrystalline with hexagonal wurtzite structures of ZnO. Also, there is no other structures have been found like Zn-Al etc. Morphological and elemental analyses have been presented that the alterations of surface, and diffusions of Al to ZnO layer. Cross-sectional images have been revealed the film thickness between 0,78-1.56 m. Optical method have been used for calculation of optical band gap values of the films which are found between 3.17-3.25 eV. The results revealed that annealing leads to diffusion from the bottom layer Al2O3 of the material to the upper layer, ZnO. In addition, it was determined that the as-deposited ZnO/Al2O3 film is still leading in terms of the investigated properties.
- 30 December 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (4) , 1026-1036
Open AccessThe Attitude of ZnO/Al2O3 Film Produced by Ultrasonic Spray Pyrolysis Under Thermal Annealing
Impact of annealing on structural, morphological, elemental, and optical properties of bilayer ZnO/Al2O3 film has been investigated. Bilayer film has been deposited on microscope slides by ultrasonic spray pyrolysis method at 350°C substrate temperature. Then, this film has been annealed at 400°C, 500°C, and 600°C under atmospheric conditions, respectively. Structural analyses have been revealed that bilayer films have polycrystalline with hexagonal wurtzite structures of ZnO. Also, there is no other structures have been found like Zn-Al etc. Morphological and elemental analyses have been presented that the alterations of surface, and diffusions of Al to ZnO layer. Cross-sectional images have been revealed the film thickness between 0,78-1.56 m. Optical method have been used for calculation of optical band gap values of the films which are found between 3.17-3.25 eV. The results revealed that annealing leads to diffusion from the bottom layer Al2O3 of the material to the upper layer, ZnO. In addition, it was determined that the as-deposited ZnO/Al2O3 film is still leading in terms of the investigated properties.
- 1 June 2022
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 35 (2) , 618-629
The Effect of Annealing Technique on ZnO Film Properties
ZnO films deposited on glass substrates by ultrasonically chemical spray pyrolysis technique have been investigated to establish the effect of the annealing technique on film properties. For this purpose, films have been exposed to standard thermal annealing and microwave annealing in an air atmosphere. It has been determined that the structural, morphological, compositional, and optical properties of the ZnO films correlate with each other. X-ray diffraction analyses have been revealed the highest crystallization level and changing preferred orientations for microwave annealed films. It has been identified that the optical band gap values of the films decreased from 3.27 eV to 3.23 eV and 3.21 eV after the standard and microwave thermal annealing, respectively. Scanning electron microscope images have been revealed homogeneous morphology at plan-view images of all films. Also, it has been determined that the root-like morphology from the higher magnification scanning electron microscopy images. Thicknesses of the films have been also determined from cross-sectional scanning electron microscope images as 1.04m, 0.92m, and 0.92m for ZnO, standard thermal annealed and microwave annealed ZnO films, respectively. Also, the O/Zn ratio revealed improved stoichiometry for annealed films according to as-deposited film for investigated regions. The dependence of photoluminescence intensity on annealing technique has also been investigated in the current study.
- 1 June 2022
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 35 (2) , 618-629
The Effect of Annealing Technique on ZnO Film Properties
ZnO films deposited on glass substrates by ultrasonically chemical spray pyrolysis technique have been investigated to establish the effect of the annealing technique on film properties. For this purpose, films have been exposed to standard thermal annealing and microwave annealing in an air atmosphere. It has been determined that the structural, morphological, compositional, and optical properties of the ZnO films correlate with each other. X-ray diffraction analyses have been revealed the highest crystallization level and changing preferred orientations for microwave annealed films. It has been identified that the optical band gap values of the films decreased from 3.27 eV to 3.23 eV and 3.21 eV after the standard and microwave thermal annealing, respectively. Scanning electron microscope images have been revealed homogeneous morphology at plan-view images of all films. Also, it has been determined that the root-like morphology from the higher magnification scanning electron microscopy images. Thicknesses of the films have been also determined from cross-sectional scanning electron microscope images as 1.04m, 0.92m, and 0.92m for ZnO, standard thermal annealed and microwave annealed ZnO films, respectively. Also, the O/Zn ratio revealed improved stoichiometry for annealed films according to as-deposited film for investigated regions. The dependence of photoluminescence intensity on annealing technique has also been investigated in the current study.
- 9 December 2021
- Published by Elsevier in Micro and Nanostructures
- Vol. 164, 107113
Design and characterization of single bilayer ZnO/Al2O3 film by ultrasonically spray pyrolysis and its application in photocatalysis
- 9 December 2021
- Published by Elsevier in Micro and Nanostructures
- Vol. 164, 107113
Design and characterization of single bilayer ZnO/Al2O3 film by ultrasonically spray pyrolysis and its application in photocatalysis
- 28 May 2021
- Published by Springer Nature in Applied Physics A
- Vol. 127 (6) , 1-10
Insight of mechanical and morphological properties of ALD- Al2O3 films in point of structural properties
- 28 May 2021
- Published by Springer Nature in Applied Physics A
- Vol. 127 (6) , 1-10
Insight of mechanical and morphological properties of ALD- Al2O3 films in point of structural properties
- 9 April 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (9) , 12059-12074
Investigations of some physical properties of ALD growth ZnO films: effect of crystal orientation on photocatalytic activity
- 9 April 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (9) , 12059-12074
Investigations of some physical properties of ALD growth ZnO films: effect of crystal orientation on photocatalytic activity