Peter Gerges Melek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter Gerges Melek has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Sameh Gaawan
Helwan University, Faculty of Engineering Mataria Branch, Civil Engineering Department, Ibrahim Abdel Razeq Street, Cairo 11718, Egypt
3 shared publications- Ashraf Osman
Structural Engineering Department, Cairo University, Giza, Egypt
2 shared publications Mohamed Hussein
Dar Al-Handasah Consultants, Structures Department, Street 26 Building 10 - Smart Village, Giza 12577, Egypt
2 shared publications- Sameh Gaawan
Civil Engineering Department, Faculty of Engineering Mataria, Helwan University, Cairo 11718, Egypt
1 shared publication
Latest Publications
- 19 April 2020
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 20 (4) , 1115-1134
Strengthening Steel CHS X-Joints Subject to Compression by Outer Ring stiffeners
- 19 April 2020
- Published by Springer Nature in International Journal of Steel Structures
- Vol. 20 (4) , 1115-1134
Strengthening Steel CHS X-Joints Subject to Compression by Outer Ring stiffeners
- 1 March 2020
- Published by Canadian Science Publishing in Canadian Journal of Civil Engineering
- Vol. 47 (3) , 301-316
Axial strength of steel circular hollow section (CHS) X-joints strengthened by flanged larger pipe
In steel design, enhancing the structural joints’ capacity is considered a challenge that faces the designer. This challenge becomes more difficult when it comes to enhancing the capacities of circular hollow section (CHS) joints due to their closed nature that complicates the strengthening process. Recent research related to strengthening T-joints by utilizing two outer hollow ring flanges welded to additional pipe showed that this technique can significantly improve the joints’ strength. In this study, the utilization of this technique is extended for enhancing the axial strength of CHS X-joints. In this regard, a parametric study using finite element models was carried out to investigate the different design aspects that might affect the behavior of strengthened X-joints. The examined parameters included, the ring flange diameter, the stiffening pipe thickness and length for different brace diameter-to-chord diameter ratios and chord diameter to double chord thickness ratio. The results demonstrated that these strengthened X-joints gained significant axial strength that reached up to three times the axial strength of the unstrengthened joints. Guidelines for proper detailing of such strengthening scheme were provided. Finally, an equation that estimates the axial strength of strengthened joints was established based on the achieved results.
- 1 March 2020
- Published by Canadian Science Publishing in Canadian Journal of Civil Engineering
- Vol. 47 (3) , 301-316
Axial strength of steel circular hollow section (CHS) X-joints strengthened by flanged larger pipe
In steel design, enhancing the structural joints’ capacity is considered a challenge that faces the designer. This challenge becomes more difficult when it comes to enhancing the capacities of circular hollow section (CHS) joints due to their closed nature that complicates the strengthening process. Recent research related to strengthening T-joints by utilizing two outer hollow ring flanges welded to additional pipe showed that this technique can significantly improve the joints’ strength. In this study, the utilization of this technique is extended for enhancing the axial strength of CHS X-joints. In this regard, a parametric study using finite element models was carried out to investigate the different design aspects that might affect the behavior of strengthened X-joints. The examined parameters included, the ring flange diameter, the stiffening pipe thickness and length for different brace diameter-to-chord diameter ratios and chord diameter to double chord thickness ratio. The results demonstrated that these strengthened X-joints gained significant axial strength that reached up to three times the axial strength of the unstrengthened joints. Guidelines for proper detailing of such strengthening scheme were provided. Finally, an equation that estimates the axial strength of strengthened joints was established based on the achieved results.
- 1 October 2017
- Published by Canadian Science Publishing in Canadian Journal of Civil Engineering
- Vol. 44 (10) , 783-801
Confining T-joints by adding two outer hollow ring flanges welded to additional hollow circular pipe
Increasing the capacity of circular hollow section (CHS) T-joints is a challenge for the designers due to its closed nature that makes strengthening difficult as the traditional strengthening techniques focus on adding ring stiffeners inside the chord, these techniques require splitting the chord at each joint location into more than one part and this is not applicable for stiffening prefabricated and erected T-joints. This paper presents a proposed strengthening technique that is based on confining the T-joint by two outer hollow ring flanges welded to additional hollow circular pipe. A parametric study is carried out to investigate the effect of the hollow ring flanges diameter, the added elements thickness, and the spacing between the hollow outer ring flanges on increasing the capacity of T-joints for different values of β (db/d0: brace diameter-to-chord diameter ratio) when the brace is either subjected to tension or compression force. Finally, it is observed that the compressive T-joints gain up to 267% of its original capacity and the tensile T-joints gain up to 65% of its original capacity.
- 1 October 2017
- Published by Canadian Science Publishing in Canadian Journal of Civil Engineering
- Vol. 44 (10) , 783-801
Confining T-joints by adding two outer hollow ring flanges welded to additional hollow circular pipe
Increasing the capacity of circular hollow section (CHS) T-joints is a challenge for the designers due to its closed nature that makes strengthening difficult as the traditional strengthening techniques focus on adding ring stiffeners inside the chord, these techniques require splitting the chord at each joint location into more than one part and this is not applicable for stiffening prefabricated and erected T-joints. This paper presents a proposed strengthening technique that is based on confining the T-joint by two outer hollow ring flanges welded to additional hollow circular pipe. A parametric study is carried out to investigate the effect of the hollow ring flanges diameter, the added elements thickness, and the spacing between the hollow outer ring flanges on increasing the capacity of T-joints for different values of β (db/d0: brace diameter-to-chord diameter ratio) when the brace is either subjected to tension or compression force. Finally, it is observed that the compressive T-joints gain up to 267% of its original capacity and the tensile T-joints gain up to 65% of its original capacity.