Efthymios C. Dourdounis
Efthymios C. Dourdounis has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Athanasios S. Tazedakis
Corinth Pipeworks S.A., Industrial Area of Voiotia, Thisvi, 32010 Domvraina, Greece
2 shared publications - Christos Palagas
Corinth Pipeworks S. A., Thisvi 32001, Greece
1 shared publication - Dimitrios E. Manolakos
National Technical University of Athens
1 shared publication Dimitrios Pantelis
Shipbuilding Technology Laboratory, School of Naval Architecture and Marine Engineering, National Technical University of Athens, 15780 Athens, Greece
1 shared publication- Giannoula Chatzopoulou
Department of Mechanical Engineering, University of Thessaly, Volos 38334, Greece
1 shared publication - Helen P. Kyriakopoulou
Shipbuilding Technology Laboratory, School of Naval Architecture and Marine Engineering, National Technical University of Athens, 15780 Athens, Greece
1 shared publication
Latest Publications
- Open Access
- 20 April 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (4) , 430
Investigation of Hydrogen Embrittlement Susceptibility and Fracture Toughness Drop after in situ Hydrogen Cathodic Charging for an X65 Pipeline Steel
The present research focuses on the investigation of an in situ hydrogen charging effect during Crack Tip Opening Displacement testing (CTOD) on the fracture toughness properties of X65 pipeline steel. This grade of steel belongs to the broader category of High Strength Low Alloy Steels (HSLA), and its microstructure consists of equiaxed ferritic and bainitic grains with a low volume fraction of degenerated pearlite islands. The studied X65 steel specimens were extracted from pipes with 19.15 mm wall thickness. The fracture toughness parameters were determined after imposing the fatigue pre-cracked specimens on air, on a specific electrolytic cell under a slow strain rate bending loading (according to ASTM G147-98, BS7448, and ISO12135 standards). Concerning the results of this study, in the first phase the hydrogen cations’ penetration depth, the diffusion coefficient of molecular and atomic hydrogen, and the surficial density of blisters were determined. Next, the characteristic parameters related to fracture toughness (such as J, KQ, CTODel, CTODpl) were calculated by the aid of the Force-Crack Mouth Open Displacement curves and the relevant analytical equations.
- 20 April 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (4) , 430
Open AccessInvestigation of Hydrogen Embrittlement Susceptibility and Fracture Toughness Drop after in situ Hydrogen Cathodic Charging for an X65 Pipeline Steel
The present research focuses on the investigation of an in situ hydrogen charging effect during Crack Tip Opening Displacement testing (CTOD) on the fracture toughness properties of X65 pipeline steel. This grade of steel belongs to the broader category of High Strength Low Alloy Steels (HSLA), and its microstructure consists of equiaxed ferritic and bainitic grains with a low volume fraction of degenerated pearlite islands. The studied X65 steel specimens were extracted from pipes with 19.15 mm wall thickness. The fracture toughness parameters were determined after imposing the fatigue pre-cracked specimens on air, on a specific electrolytic cell under a slow strain rate bending loading (according to ASTM G147-98, BS7448, and ISO12135 standards). Concerning the results of this study, in the first phase the hydrogen cations’ penetration depth, the diffusion coefficient of molecular and atomic hydrogen, and the surficial density of blisters were determined. Next, the characteristic parameters related to fracture toughness (such as J, KQ, CTODel, CTODpl) were calculated by the aid of the Force-Crack Mouth Open Displacement curves and the relevant analytical equations.
- 13 August 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 141 (1)
Numerical Simulation of JCO-E Pipe Manufacturing Process and Its Effect on the External Pressure Capacity of the Pipe1
Large-diameter thick-walled steel pipes during their installation in deep-water are subjected to external pressure, which may trigger structural instability due to pipe ovalization, with detrimental effects. The resistance of offshore pipes against this instability is affected by local geometric deviations and residual stresses, introduced by the line pipe manufacturing process. In the present paper, the JCO-E pipe manufacturing process, a commonly adopted process for producing large-diameter pipes of significant thickness, is examined. The study examines the effect of JCO-E line pipe manufacturing process on the external pressure resistance of offshore pipes, candidates for deepwater applications using nonlinear finite element simulation tools. The cold bending induced by the JCO forming process as well as the subsequent welding and expansion (E) operations are simulated rigorously. Subsequently, the application of external pressure is modeled until structural instability (collapse) is detected. Both the JCO-E manufacturing process and the external pressure response of the pipe, are modeled using a two-dimensional (2D) generalized plane strain model, together with a coupled thermo-mechanical model for simulating the welding process.
- 13 August 2018
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 141 (1)
Numerical Simulation of JCO-E Pipe Manufacturing Process and Its Effect on the External Pressure Capacity of the Pipe1
Large-diameter thick-walled steel pipes during their installation in deep-water are subjected to external pressure, which may trigger structural instability due to pipe ovalization, with detrimental effects. The resistance of offshore pipes against this instability is affected by local geometric deviations and residual stresses, introduced by the line pipe manufacturing process. In the present paper, the JCO-E pipe manufacturing process, a commonly adopted process for producing large-diameter pipes of significant thickness, is examined. The study examines the effect of JCO-E line pipe manufacturing process on the external pressure resistance of offshore pipes, candidates for deepwater applications using nonlinear finite element simulation tools. The cold bending induced by the JCO forming process as well as the subsequent welding and expansion (E) operations are simulated rigorously. Subsequently, the application of external pressure is modeled until structural instability (collapse) is detected. Both the JCO-E manufacturing process and the external pressure response of the pipe, are modeled using a two-dimensional (2D) generalized plane strain model, together with a coupled thermo-mechanical model for simulating the welding process.