TITakeki Itoh

Takeki Itoh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Takeki Itoh has a total of 58 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Heated-H3PO4 etching of (001) β-Ga2O3

    by Steve Rebollo, Takeki Itoh, Sriram Krishnamoorthy, James S. Speck

    β-Ga2O3 is a promising ultra-wide bandgap semiconductor with melt-grown substrates that are scalable, particularly in the (001) orientation. In this study, we report on the heated-phosphoric acid etching of (001) β-Ga2O3. A wagon wheel pattern with spokes aligned to a range of specific crystallographic directions was fabricated on (001) β-Ga2O3. At 160 °C, the (001) etch rate was 1.47 μm/h, which is comparable to etch rates obtained via dry etch techniques. The etched (001) surface had a morphology that was smoother than an inductively coupled plasma etched surface. All spokes possessed relatively smooth sidewalls. Spokes oriented along the [100] direction exhibited minimal SiO2 mask undercut rates at lower etch temperatures and symmetric trapezoidal profiles with near vertical (010)-like sidewalls, which are ideal for device structures with a trench geometry. Spokes oriented along the [010] direction exhibited significant SiO2 mask undercut rates and asymmetric trapezoidal profiles with different sidewall angles. These spokes also possessed reduced sidewall angles, which is favorable for field management at device corners and edges. The etch process was used to realize a dense array of [100]-oriented trenches with a height of 1.5 μm, a base width of 2.0 μm, and a mask width of 0.8 μm. The work highlights the potential for ion damage-free, standalone heated-H3PO4 etching as a viable alternative to the dry etching of (001) β-Ga2O3 for high-performance device applications.


  • (Invited) Gallium Nitride for Vertical Power Devices: Improving Morphology and Unintentional Impurities for Better Devices

    by James S. Speck, Esmat Farzana, Kai Shek Qwah, Zachary J. Biegler, Ashley Wissel-Garcia, Iris Celupica-Liu, Takeki Itoh

    While GaN has been researched for many years as a material for light emitting diodes, lasers, high electron mobility transistors, and other devices, further improvements to material purity are still needed to realize the full potential of this material for vertical device applications. To achieve high quality, high purity GaN for power devices, our research employs ammonia-assisted molecular beam epitaxy (NH3-MBE) and plasma-assisted molecular beam epitaxy (PA-MBE). Past studies of fast growth rates (more than 1 μm/hr) and ultra-low impurity incorporation revealed that both PAMBE and NH3-MBE can achieve low net doping levels, and NH3-MBE as low as 1x1015 cm-3.1 However, This work also indicated that impurity incorporation increased with increasing growth rate. Recent research efforts have focused on further improvements to morphology and unintentional dopants in NH3-MBE-grown homoepitaxial layers with fast growth rates. By optimizing growth conditions for faster growth rates and using indium as a surfactant, devices with drift layers up to 10 μm thick were grown. These layers exhibited smooth surface morphology as seen in AFM scans with RMS surface roughness as low as 0.21 nm for a 2x2 μm2 scan area.2 Adding the In surfactant also led to reduced incorporation of unintentional Si impurities in UID films as shown by SIMS depth profiles for GaN films grown with and without In. The extremely low impurity levels were further confirmed by CV measurements which indicated that the net doping density in the UID GaN layers decreased from 2x1016 cm-3 to 5x1015 cm-3 with the addition of the In surfactant.2 Based on these UID levels and the theoretical critical electric field of GaN (3 MV/cm), drift layers up to 29.5 μm and 7.4 μm can be depleted with a triangular electric field profile for net donor concentrations of 5x1015 cm-3 and 2x1016 cm-3, respectively. Devices with the same net concentrations with drift regions 3 μm thick can hold voltages of 854 V and 717 V, respectively. Based on the previously described studies of low-impurity GaN at different growth rates, we developed vertical p-n GaN power devices grown by NH3 MBE.3 These p-n diodes contained a 0.25 µm n+ region, 4 µm n- region with 3x1015 cm-3 unintentional carriers, 0.4 µm p+ region and 10nm p++ capping layer to improve the ohmic anode contact. The circular diodes were fabricated with Pd/Pt anode contacts and Ti/Au cathode contacts. Device diameters were between 80 and 100 µm. The devices featured a 15 µm field plate made from Ti/Au contacts on top of an Al2O3/Si3N4 dielectric stack. The diodes exhibited outstanding forward J-V behavior with a low specific on-resistance (Ron,sp) of 0.28 mΩ-cm2 and a minimum ideality factor of 1.36, which are among the best achieved among similar homoepitaxial GaN p-n diodes.3-5 The best diodes also exhibited a breakdown voltage of > 1 kV (equipment limit 1 kV). The reverse-voltage properties indicate that punch-through was achieved with a peak electric field (EC) >2.6 MV/cm, as confirmed by Silvaco simulations (Fig. 7). The combination of >1 kV breakdown voltage and on-resistance of 0.28 mΩ-cm2 represents one of the best performances of the p-n GaN diodes, achieved with a significantly thinner drift layer compared to comparable MOCVD GaN p-n diodes with drift layers more than 8 µm. Work is ongoing to develop NH3-MBE p-n diodes with indium surfactant-assisted drift layer growth which shows promise to further improve the surface morphology, reduce leakage, and enhance breakdown performance of the vertical devices.

  • Open Access

    Controllable nitrogen doping of MOCVD Ga2O3 using NH3

    by Fikadu Alema, Takeki Itoh, William Brand, Andrei Osinsky, James S. Speck

    We report on the controllable nitrogen doping of β-Ga2O3 as a deep acceptor dopant using ammonia diluted in nitrogen (NH3/N2) as a source of active nitrogen in the metal organic chemical vapor deposition epitaxy. The effects of the NH3/N2 flow rate and substrate temperature on the incorporation efficiency, reproducibility, and controllability of N doping into Ga2O3 were studied using secondary ion mass spectrometry measurements. With the increase in the NH3/N2 molar flow rate from ∼2 × 10−8 to ∼2 × 10−6 mol/min, the N impurities incorporated into the β-Ga2O3 increased linearly from ∼1 × 1018 to ∼2 × 1020 cm−3. At low substrate temperatures (70 MΩ for a film grown with [N] ≈ [H] of ∼8 × 1018 cm−3. X-ray on-axis (020) and off-axis (111) rocking curve ω-scans and atomic force microscopy measurements show no influence of NH3/N2 dopant on the structural and surface quality of the films. However, the presence of H promoted the growth of (110) and (1¯10) facets elongated along the [001] direction. At high growth temperatures (≥950 °C), the H concentration in the films was reduced by nearly ∼10×, but with a slight increase in the concentration of N. The results show that controllable and repeatable nitrogen doping into β-Ga2O3 can be achieved using ammonia to obtain deep acceptor doping or compensation needed for device engineering in β-Ga2O3-based power electronic devices.


  • Open Access

    N2O grown high Al composition nitrogen doped β-(AlGa)2O3/β-Ga2O3 using MOCVD

    by Fikadu Alema, Takeki Itoh, William Brand, Marko Tadjer, Andrei Osinsky, James S. Speck

    We report on the MOCVD growth of smooth (010) (AlxGa1–x)2O3 and (100) (AlyGa1–y)2O3 epitaxial films on β-Ga2O3 substrates with (010) and (100) orientations, respectively, using N2O for oxidation. High resolution x-ray diffraction was used to evaluate the phase purity and strain characteristics of the (AlGa)2O3 layers and estimate the Al composition. The incorporation efficiency of Al into the (AlGa)2O3 films depends on process conditions, including chamber pressure, growth temperature, and gas phase Al concentration. Layers grown at lower reactor pressure and substrate temperature and higher gas phase Al concentration showed higher Al incorporation. Pure beta phase (AlGa)2O3 films with a record high Al composition of x = 30% for a film grown on a (010) β-Ga2O3 substrate and with an Al composition of up to y = 45% on the (100) β-Ga2O3 substrate was realized by introducing ∼18% Al mole fraction into the reactor. N2O grown β-(AlGa)2O3/β-Ga2O3 superlattice structures with an Al composition of 5% were also demonstrated on both substrate orientations. When higher gas phase Al concentration is introduced into the reactor, pure γ-phase (AlxGa1–x)2O3 is grown on (010) β-Ga2O3 substrates. In contrast, on the (100) β-Ga2O3 substrate, the (AlyGa1–y)2O3 layers are β-phase, but with two separate Al compositions owing to the local Al segregation. The nitrogen doping of (010) β-(AlxGa1–x)2O3 with [N] ranging 6 × 1017–2 × 1019 cm−3 was achieved using N2O. Higher Al composition and lower substrate temperature lead to higher N incorporation. The results show that using N2O as an oxygen source can lead to the growth of high Al content β-(AlGa)2O3, which paves the way for the realization of efficient power devices, such as modulation-doped field effect transistors.


  • Open Access

    Continuous Si doping in (010) and (001) β-Ga2O3 films by plasma-assisted molecular beam epitaxy

    by Takeki Itoh, Akhil Mauze, Yuewei Zhang, James S. Speck

    We report the continuous Si doping in β-Ga2O3 epitaxial films grown by plasma-assisted molecular beam epitaxy through the use of a valved effusion cell for the Si source. Secondary ion mass spectroscopy results exhibit that the Si doping profiles in β-Ga2O3 are flat and have sharp turn-on/off depth profiles. The Si doping concentration was able to be controlled by either varying the cell temperatures or changing the aperture of the valve of the Si effusion cell. High crystal quality and smooth surface morphologies were confirmed on Si-doped β-Ga2O3 epitaxial films grown on (010) and (001) substrates. The electronic properties of Si-doped (001) β-Ga2O3 epitaxial film showed an electron mobility of 67 cm2/Vs at the Hall concentration of 3 × 1018 cm−3.


  • Top Cited Papers
    Open Access

    Enhancing the electron mobility in Si-doped (010) β-Ga2O3 films with low-temperature buffer layers

    by Arkka Bhattacharyya, Carl Peterson, Takeki Itoh, Saurav Roy, Jacqueline Cooke, Steve Rebollo, Praneeth Ranga, Berardi Sensale-Rodriguez, Sriram Krishnamoorthy

    We demonstrate a new substrate cleaning and buffer growth scheme in β-Ga2O3 epitaxial thin films using metal–organic vapor phase epitaxy (MOVPE). For the channel structure, a low-temperature (LT, 600 °C) un-doped Ga2O3 buffer was grown, followed by a transition layer to a high-temperature (HT, 810 °C) Si-doped Ga2O3 channel layers without growth interruption. The (010) Ga2O3 Fe-doped substrate cleaning uses solvent cleaning, followed by additional hydrofluoric acid (49% in water) treatment for 30 min before the epilayer growth. This step is shown to compensate the parasitic Si channel at the epilayer–substrate interface that originates from the substrate polishing process or contamination from the ambient. From secondary ion mass spectroscopy (SIMS) analysis, the Si peak atomic density at the substrate interface is found to be several times lower than the Fe atomic density in the substrate—indicating full compensation. The elimination of the parasitic electron channel at the epi–substrate interface was also verified by electrical (capacitance–voltage profiling) measurements. In the LT-grown (600 °C) buffer layers, it is seen that the Fe forward decay tail from the substrate is very sharp, with a decay rate of ∼9 nm/dec. X-ray off-axis rocking curve ω-scans show very narrow full width at half maximum (FWHM) values, similar to the as-received substrates. These channels show record high electron mobility in the range of 196–85 cm2/V⋅s in unintentionally doped and Si-doped films in the doping range of 2 × 1016–1 × 1020 cm−3. Si delta-doped channels were also grown utilizing this substrate cleaning and the hybrid LT buffers. Record high electron Hall mobility of 110 cm2/V⋅s was measured for sheet charge density of 9.2 × 1012 cm−2. This substrate cleaning, combined with the LT buffer scheme, shows the potential of designing Si-doped β-Ga2O3 channels with exceptional transport properties for high-performance Ga2O3-based electron devices.


  • Open Access

    Oxidized metal Schottky contact with high-κ dielectric field plate for low-loss high-power vertical β-Ga2O3 Schottky diodes

    by Esmat Farzana, Arkka Bhattacharyya, Nolan S. Hendricks, Takeki Itoh, Sriram Krishnamoorthy, James S. Speck

    We report on vertical β-Ga2O3 power diodes with oxidized-metal Schottky contact (PtOx) and high permittivity (high-κ) dielectric (ZrO2) field plate to improve reverse blocking at both Schottky contact surfaces and edges. The PtOx diodes showed excellent forward transport with near unity ideality factor and similar minimum specific on-resistance as Pt. Moreover, the PtOx contacts facilitated higher breakdown voltage and lower leakage current due to their higher Schottky barrier height (SBH) by more than 0.5 eV compared to that of Pt. Most importantly, the reduced off-state leakage of PtOx diodes enabled orders of magnitude less power dissipation than Pt ones for all duty cycles ≤0.5, indicating their great potential to realize low-loss and efficient, high-power β-Ga2O3 switches. The ZrO2 field-oxide further reduced edge leakage with a consistent increase in breakdown voltage. Device simulation demonstrated that the high permittivity of ZrO2 also led to the peak electric field occurring in β-Ga2O3 instead of the dielectric. These results indicate that the combined integration of oxidized-metal contacts to increase SBH and high-κ dielectric field plate to assist edge termination can be promising to enhance the performance of vertical β-Ga2O3 Schottky diodes.


  • Coherently strained (001) β-(AlxGa1−x)2O3 thin films on β-Ga2O3: Growth and compositional analysis

    by Akhil Mauze, Takeki Itoh, Yuewei Zhang, Evelyn Deagueros, Feng Wu, James S. Speck

    In this work, we report on the growth of (001) β-(AlxGa1−x)2O3 films in molecular beam epitaxy via metal oxide-catalyzed epitaxy. Films with Al contents up to 15% were grown and the Al content was measured with atom probe tomography. A relationship between the Al content and the out-of-plane lattice parameter was derived for both (001) and (100) orientations. Transmission electron microscopy showed no evidence of extended defects in (001) β-(AlxGa1−x)2O3, and reciprocal space maps confirmed that β-(AlxGa1−x)2O3 films were coherently strained to (001) β-Ga2O3. Sn was also demonstrated to act as a surfactant for (001) β-(AlxGa1−x)2O3 growth, allowing for high-quality, uniform films with smooth morphologies.


  • Open Access

    Surface reaction dependence of molecular beam epitaxy grown aluminum on various orientations of β-Ga2O3

    by Kenny Huynh, Michael E. Liao, Akhil Mauze, Takeki Itoh, Xingxu Yan, James S. Speck, Xiaoqing Pan, Mark S. Goorsky

    An orientational dependence on the interfacial reaction between aluminum and (010), (001), and (2̄ 01) β-Ga2O3 substrates is addressed. Electron microscopy and x-ray diffraction were used to assess the interface crystallinity, thickness, and chemical composition of the interfacial layers. At the interface, amorphous aluminum oxide is observed in all three samples with a thicknesses of 3.5 nm for (010) β-Ga2O3 and 2 nm for (001) β-Ga2O3 and (2̄ 01) β-Ga2O3. Aluminum oxide is formed at the interface as a result of a chemical reaction that reduces the Ga2O3 surface when aluminum is deposited. We propose that in Al on (010) β-Ga2O3, in which the thickest interfacial oxide layer is observed, diffusional pathways of consecutive octahedral Ga sites perpendicular to the interface promote increased interdiffusion in the out-of-plane direction. In contrast, the (001) β-Ga2O3 and (2̄ 01) β-Ga2O3 substrates exhibit alternating rows of tetrahedral and octahedral Ga sites parallel to the interface, where the rows of tetrahedral Ga sites act as increased energy barriers that impede interdiffusion of Al and β-Ga2O3. The orientational dependence of metal-oxide interlayers in β-Ga2O3 can impact electronic and thermal transport, pointing to the importance of understanding the impact of β-Ga2O3 orientation on interfacial properties.


  • Mg doping and diffusion in (010) β-Ga2O3 films grown by plasma-assisted molecular beam epitaxy

    by Akhil Mauze, Yuewei Zhang, Takeki Itoh, Thomas E. Mates, Hartwin Peelaers, Chris G. Van de Walle, James S. Speck

    In this work, we report the growth of Mg-doped (010) β-Ga2O3 via plasma-assisted molecular beam epitaxy. Mg concentrations from 2 × 1016 to 8 × 1020 cm−3 with sharp doping profiles were realized. The Mg doping incorporation in β-Ga2O3 showed little dependence on the growth temperature and Ga:O flux ratio. Annealing at temperatures from 925 to 1050 °C resulted in significant diffusion, thus limiting the application of Mg-doped β-Ga2O3 to lower temperature growth techniques and processing. Mg accumulation near the sample surface after diffusion gives insight into the rich point–defect interaction that may play an important role in Mg diffusion.