Geoff Eichhorn
Research Subjects
Geoff Eichhorn has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Greg Siemens
Royal Military College of Canada
2 shared publications - Stuart Kenneth Haigh
Univ. of Cambridge
2 shared publications Anna Leuprecht
Department of Civil Engineering, Royal Military College of Canada 2 , Room 2423, Sawyer Building Mod 4, 13 General Crerar Crescent, Kingston, Ontario K7K 7B4
1 shared publication- April J. Bowman
U.S. Army Engineer Research and Development Center (ERDC) , Vicksburg
1 shared publication Azin Mardani
1 shared publicationCedric Rugwizangoga
1 shared publication
Latest Publications
- 26 August 2026
- Published by ASTM International in Geotechnical Testing Journal
- Vol. 49 (6)
An Open-Source 3D Soil Printer for Physical Modeling and Element Testing
High-quality physical modeling and laboratory element testing of reconstituted granular materials rely on the creation of models and test specimens to specific properties with repeatable and reliable structure and shape. Ideally, identical models and test specimens are created with precise and accurate, homogeneous or heterogeneous properties such that repeat tests provide consistent outcomes. Recently, automated 2D and 3D printing capabilities have been developed and applied to many industries, including soil printing using air pluviation; however, all currently available soil printers are unique to their location of development or only available commercially, both of which limit distribution and further customization. In this paper, a fused deposition modeling 3D printer is modified to create an open-source, automated, and scalable 3D printer for granular materials. Well-established air pluviation principles using the combined effects of drop height and mass flow rate to achieve a target soil density are combined with additional options to create customizable shapes (i.e., slopes) as well as geological bedforms such as cross-bedding. The Royal Military College 3D printer can construct repeatable and replicable models/specimens up to a size of 40.0 cm × 48.5 cm × 34.0 cm in terms of length, width, and height, over a wide range of relative density (45–100 %). Internal consistency in soil prints is confirmed through vertical as well as lateral density tests, showing variation less than 0.4 % and 0.8 % from mean values. Consolidated undrained triaxial tests performed on three repeat test specimens display nominally equivalent stress, strain, and pore pressure response up to shear band development. Included in the supplementary information are a complete parts list, design drawings, printer manual, guidance for construction, python code, and example videos of model prints.
- 26 August 2026
- Published by ASTM International in Geotechnical Testing Journal
- Vol. 49 (6)
An Open-Source 3D Soil Printer for Physical Modeling and Element Testing
High-quality physical modeling and laboratory element testing of reconstituted granular materials rely on the creation of models and test specimens to specific properties with repeatable and reliable structure and shape. Ideally, identical models and test specimens are created with precise and accurate, homogeneous or heterogeneous properties such that repeat tests provide consistent outcomes. Recently, automated 2D and 3D printing capabilities have been developed and applied to many industries, including soil printing using air pluviation; however, all currently available soil printers are unique to their location of development or only available commercially, both of which limit distribution and further customization. In this paper, a fused deposition modeling 3D printer is modified to create an open-source, automated, and scalable 3D printer for granular materials. Well-established air pluviation principles using the combined effects of drop height and mass flow rate to achieve a target soil density are combined with additional options to create customizable shapes (i.e., slopes) as well as geological bedforms such as cross-bedding. The Royal Military College 3D printer can construct repeatable and replicable models/specimens up to a size of 40.0 cm × 48.5 cm × 34.0 cm in terms of length, width, and height, over a wide range of relative density (45–100 %). Internal consistency in soil prints is confirmed through vertical as well as lateral density tests, showing variation less than 0.4 % and 0.8 % from mean values. Consolidated undrained triaxial tests performed on three repeat test specimens display nominally equivalent stress, strain, and pore pressure response up to shear band development. Included in the supplementary information are a complete parts list, design drawings, printer manual, guidance for construction, python code, and example videos of model prints.
- Open Access
- 18 March 2025
- Published by Copernicus GmbH
Physical modelling of thaw slumps in a geotechnical centrifuge
Retrogressive thaw slumps are a well-known arctic geohazard, which often occur in ice-rich permafrost. Thaw slumps can be triggered by warming and/or anthropogenic influences. Consequences of thaw slumps include changes to the landscape, impacts to infrastructure, sediment and solute loads to watersheds, and release of stored carbon, among other effects. Many studies on thaw slumps in nature include external monitoring through use of time-lapse photography, unmanned aerial vehicle (UAV), and lidar surveys. While field studies using external monitoring equipment provide high quality information about the extent and consequence of thaw slumps, direct observations of thermal and mechanical mechanisms occurring behind the scarp normally remain hidden. Recent advances at Royal Military College of Canada (RMC) used physical modeling to examine cold regions phenomena with a geotechnical centrifuge. Geotechnical centrifuges apply elevated gravity to small-scale models to create stress-equivalent environments and allow for direct observation of subsurface displacements from digital images of the model's side profile. Instrumentation in thaw slump physical models includes internal temperature measurements using fiber optics and scarp face temperature measurements using a thermal camera. Preliminary results indicate that the thaw slump physical models are conceptually capturing key behaviours observed from external field measurements. Typically, warming begins at the face and surface leading to thawing and and episodic thaw slump events. Failed material migrates downward and away from the intact block. This mechanism repeats until the final slump occurs . Internal displacements, measured using digital image corellation (DIC), show corellation with co-located temperature measurements. Results also show higher ice contents and taller scarps tend to lead to shear failure while lower ice contents and shorter scarps tend to fail via a toppling mechanism. Outcomes of the research will provide a practical analysis tool for analyzing thaw slumps as well as fundamental understanding of pre-failure permafrost mechanics.
- 18 March 2025
- Published by Copernicus GmbH
Open AccessPhysical modelling of thaw slumps in a geotechnical centrifuge
Retrogressive thaw slumps are a well-known arctic geohazard, which often occur in ice-rich permafrost. Thaw slumps can be triggered by warming and/or anthropogenic influences. Consequences of thaw slumps include changes to the landscape, impacts to infrastructure, sediment and solute loads to watersheds, and release of stored carbon, among other effects. Many studies on thaw slumps in nature include external monitoring through use of time-lapse photography, unmanned aerial vehicle (UAV), and lidar surveys. While field studies using external monitoring equipment provide high quality information about the extent and consequence of thaw slumps, direct observations of thermal and mechanical mechanisms occurring behind the scarp normally remain hidden. Recent advances at Royal Military College of Canada (RMC) used physical modeling to examine cold regions phenomena with a geotechnical centrifuge. Geotechnical centrifuges apply elevated gravity to small-scale models to create stress-equivalent environments and allow for direct observation of subsurface displacements from digital images of the model's side profile. Instrumentation in thaw slump physical models includes internal temperature measurements using fiber optics and scarp face temperature measurements using a thermal camera. Preliminary results indicate that the thaw slump physical models are conceptually capturing key behaviours observed from external field measurements. Typically, warming begins at the face and surface leading to thawing and and episodic thaw slump events. Failed material migrates downward and away from the intact block. This mechanism repeats until the final slump occurs . Internal displacements, measured using digital image corellation (DIC), show corellation with co-located temperature measurements. Results also show higher ice contents and taller scarps tend to lead to shear failure while lower ice contents and shorter scarps tend to fail via a toppling mechanism. Outcomes of the research will provide a practical analysis tool for analyzing thaw slumps as well as fundamental understanding of pre-failure permafrost mechanics.
- 1 November 2024
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 24 (6) , 298-312
Pressure and thermal effects on Rayleigh fibre-optic strain measurement for soil–structure interaction
Optical strain sensing for structural health monitoring is sometimes deployed for field and laboratory study of civil structures. Rayleigh backscatter devices (ROFDR) are presented for use with geotechnical centrifuge research since they offer distributed sensing capabilities, and through this study are shown to have negligible interference from external pressure effects. A comparison between a single channel and multi-channel fibre optic rotary joint (FORJ) is presented in the context of transmitting optical strain data across a rotating interface. The orthogonal pressure effects of a free-floating fibre under isotropic pressure was 12 h constant temperature test. An example case of a pipeline buried in a slope experiencing a landslide is presented using fiber pairs to capture pipe stress / strain. Geotechnical centrifuge modelling in a 1 m drum was carried out using a multi-channel FORJ coupled with an ROFDR system.
- 1 November 2024
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 24 (6) , 298-312
Pressure and thermal effects on Rayleigh fibre-optic strain measurement for soil–structure interaction
Optical strain sensing for structural health monitoring is sometimes deployed for field and laboratory study of civil structures. Rayleigh backscatter devices (ROFDR) are presented for use with geotechnical centrifuge research since they offer distributed sensing capabilities, and through this study are shown to have negligible interference from external pressure effects. A comparison between a single channel and multi-channel fibre optic rotary joint (FORJ) is presented in the context of transmitting optical strain data across a rotating interface. The orthogonal pressure effects of a free-floating fibre under isotropic pressure was 12 h constant temperature test. An example case of a pipeline buried in a slope experiencing a landslide is presented using fiber pairs to capture pipe stress / strain. Geotechnical centrifuge modelling in a 1 m drum was carried out using a multi-channel FORJ coupled with an ROFDR system.
- 5 October 2023
- Published by Elsevier in Transportation Geotechnics
- Vol. 43
Physical modelling of climate-soil-infrastructure interactions of paved roadways constructed in expansive soil
- 5 October 2023
- Published by Elsevier in Transportation Geotechnics
- Vol. 43
Physical modelling of climate-soil-infrastructure interactions of paved roadways constructed in expansive soil
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 235
Anchor penetration depth in sandy soils and its implications for cable burial
- 1 September 2021
- Published by Elsevier in Ocean Engineering
- Vol. 235
Anchor penetration depth in sandy soils and its implications for cable burial
- Open Access
Low‐cost digital image correlation and strain measurement for geotechnical applications
Particle image velocimetry (PIV), or digital image correlation (DIC), is a widely used technique to measure soil displacements and strains in small‐scale geotechnical models. Arrays of single‐board computers (SBCs) produced by Raspberry Pi, and their associated 8‐MP cameras, are being used at the University of Cambridge to capture the images required for DIC analysis. This alternative to more expensive camera set‐ups has numerous advantages. A single expensive and large camera can be replaced—at low cost—by multiple cameras, adding flexibility and affordability to any experimental set‐up. Traditionally, the alignment of multiple cameras to each other and the referencing to a known coordinate system required painted or machined markers to be located on the observation windows through which the experiments are viewed. This can obstruct localised soil grain displacement measurements in those areas of the model where such markers are placed. To complement the Raspberry Pi camera system, a markerless calibration method was used during image acquisition. This paper outlines the set‐up of four of these small computers and associated cameras, provides an overview of the use of the markerless referencing system and reviews two different experimental apparatus used to measure soil displacement and strain. When the cost of additional cabling, connectors and mounting hardware is considered for this system, the total cost to implement was approximately $125 USD per camera plus one‐time costs of $175 USD for system peripherals, which represents outstanding value and enables practically all geotechnical laboratories to develop similar capabilities.
Open AccessLow‐cost digital image correlation and strain measurement for geotechnical applications
Particle image velocimetry (PIV), or digital image correlation (DIC), is a widely used technique to measure soil displacements and strains in small‐scale geotechnical models. Arrays of single‐board computers (SBCs) produced by Raspberry Pi, and their associated 8‐MP cameras, are being used at the University of Cambridge to capture the images required for DIC analysis. This alternative to more expensive camera set‐ups has numerous advantages. A single expensive and large camera can be replaced—at low cost—by multiple cameras, adding flexibility and affordability to any experimental set‐up. Traditionally, the alignment of multiple cameras to each other and the referencing to a known coordinate system required painted or machined markers to be located on the observation windows through which the experiments are viewed. This can obstruct localised soil grain displacement measurements in those areas of the model where such markers are placed. To complement the Raspberry Pi camera system, a markerless calibration method was used during image acquisition. This paper outlines the set‐up of four of these small computers and associated cameras, provides an overview of the use of the markerless referencing system and reviews two different experimental apparatus used to measure soil displacement and strain. When the cost of additional cabling, connectors and mounting hardware is considered for this system, the total cost to implement was approximately $125 USD per camera plus one‐time costs of $175 USD for system peripherals, which represents outstanding value and enables practically all geotechnical laboratories to develop similar capabilities.