Yongxiang Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yongxiang Wu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Ulrich Rist
Institute of Aerodynamics and Gas Dynamics
3 shared publicationsGabriel Axtmann
Institute of Aerodynamics and Gas Dynamics, University of Stuttgart, Pfaffenwaldring 21, 70569 Stuttgart, Germany
2 shared publications- Tristan M. Römer
University of Stuttgart
2 shared publications - Ulrich Rist
University of Stuttgart
2 shared publications Bernhard Weigand
Institute of Aerospace Thermodynamics, University of Stuttgart, Pfaffenwaldring 31, D-70569 Stuttgart, Germany
1 shared publicationCheng Wang
State Key Laboratory of Explosion Science and Safety Protection, Beijing Institute of Technology, Beijing 100081, PR China
1 shared publication
Latest Publications
- Open Access
- 12 March 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1007, A7
Sensitivity of three-dimensional boundary layer stability to intrinsic uncertainties of fluid properties: a study on supercritical CO2
The intrinsic uncertainty of fluid properties, including the equation-of-state, viscosity and thermal conductivity, on boundary layer stability has scarcely been addressed. When a fluid is operating in the vicinity of the Widom line (defined as the maximum of isobaric specific heat) in supercritical state, its properties exhibit highly non-ideal behavior, which is an ongoing research field leading to refined and more accurate fluid property databases. Upon crossing the Widom line, new mechanisms of flow instability emerge, feasibly leading to changes in dominating modes that yield turbulence. The present work investigates the sensitivity of three-dimensional boundary layer modal instability to these intrinsic uncertainties in fluid properties. The uncertainty, regardless of its source and the fluid regimes, gives rise to distortions of all profiles that constitute the inputs of the stability operator. The effect of these distortions on flow stability is measured by sensitivity coefficients, which are formulated with the adjoint operator and validated against linear modal stability analysis. The results are presented for carbon dioxide at a representative supercritical pressure of approximately 80 bar. The sensitivity to different inputs of the stability operator across various thermodynamic regimes shows an immense range of sensitivity amplitude. A balancing relationship between the density gradient and its perturbation leads to a quadratic effect across the Widom line, provoking significant sensitivity to distortions of the second derivative of the pressure with respect to the density, $\partial ^2 p/\partial \rho ^2$ . From an application-oriented point of view, one important question is whether the correct baseflow profiles can be meaningfully analysed by the simplified ideal-fluid model. The integrated modal disturbance growth – the N factor calculated with different partly idealised models – indicates that the answer depends strongly on the thermodynamic regime investigated.- 12 March 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1007, A7
Open AccessSensitivity of three-dimensional boundary layer stability to intrinsic uncertainties of fluid properties: a study on supercritical CO2
The intrinsic uncertainty of fluid properties, including the equation-of-state, viscosity and thermal conductivity, on boundary layer stability has scarcely been addressed. When a fluid is operating in the vicinity of the Widom line (defined as the maximum of isobaric specific heat) in supercritical state, its properties exhibit highly non-ideal behavior, which is an ongoing research field leading to refined and more accurate fluid property databases. Upon crossing the Widom line, new mechanisms of flow instability emerge, feasibly leading to changes in dominating modes that yield turbulence. The present work investigates the sensitivity of three-dimensional boundary layer modal instability to these intrinsic uncertainties in fluid properties. The uncertainty, regardless of its source and the fluid regimes, gives rise to distortions of all profiles that constitute the inputs of the stability operator. The effect of these distortions on flow stability is measured by sensitivity coefficients, which are formulated with the adjoint operator and validated against linear modal stability analysis. The results are presented for carbon dioxide at a representative supercritical pressure of approximately 80 bar. The sensitivity to different inputs of the stability operator across various thermodynamic regimes shows an immense range of sensitivity amplitude. A balancing relationship between the density gradient and its perturbation leads to a quadratic effect across the Widom line, provoking significant sensitivity to distortions of the second derivative of the pressure with respect to the density, $\partial ^2 p/\partial \rho ^2$ . From an application-oriented point of view, one important question is whether the correct baseflow profiles can be meaningfully analysed by the simplified ideal-fluid model. The integrated modal disturbance growth – the N factor calculated with different partly idealised models – indicates that the answer depends strongly on the thermodynamic regime investigated. - 23 September 2023
- Published by Springer Nature
- p. 402-411
Direct Numerical Simulation of Counter-Rotating Cylindrical Roughness Pairs for Laminar Flow Control
- 23 September 2023
- Published by Springer Nature
- p. 402-411
Direct Numerical Simulation of Counter-Rotating Cylindrical Roughness Pairs for Laminar Flow Control
- Open Access
- 13 February 2023
- Published by Springer Nature in Experiments in Fluids
- Vol. 64 (2) , 1-8
Delay of laminar–turbulent transition by counter-rotating cylindrical roughness elements in a laminar flat plate boundary layer
Delaying laminar–turbulent transition in boundary layers is of great interest since the skin-friction coefficient can be reduced by up to one order of magnitude. In this experimental research, it is shown that counter-rotating cylindrical roughness elements are able to delay transition under realistic flow conditions. Evidence is given by the intermittency, evaluated from hot-film measurements in a laminar water channel. An increase in rotation speed results in a delay of transition of up to $${6.5}{\%}$$ in the center of the plate. This trend can be explained by the streaks amplified by the rotating cylinders, resulting in a damping of the fluctuation amplitude in the boundary layer. The advantage of this method is that the transition delay can be actively controlled with conventional cylindrical roughness elements. Graphical- 13 February 2023
- Published by Springer Nature in Experiments in Fluids
- Vol. 64 (2) , 1-8
Open AccessDelay of laminar–turbulent transition by counter-rotating cylindrical roughness elements in a laminar flat plate boundary layer
Delaying laminar–turbulent transition in boundary layers is of great interest since the skin-friction coefficient can be reduced by up to one order of magnitude. In this experimental research, it is shown that counter-rotating cylindrical roughness elements are able to delay transition under realistic flow conditions. Evidence is given by the intermittency, evaluated from hot-film measurements in a laminar water channel. An increase in rotation speed results in a delay of transition of up to $${6.5}{\%}$$ in the center of the plate. This trend can be explained by the streaks amplified by the rotating cylinders, resulting in a damping of the fluctuation amplitude in the boundary layer. The advantage of this method is that the transition delay can be actively controlled with conventional cylindrical roughness elements. Graphical - Open Access
- 20 July 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 945
Transition mechanisms in a boundary layer controlled by rotating wall-normal cylindrical roughness elements
The transition to turbulence induced by counter-rotating wall-normal rotating cylindrical roughness pairs immersed within a laminar boundary layer on a flat plate is investigated with direct numerical simulations, dynamic mode decomposition (DMD) and perturbation kinetic energy (PKE) analysis. As long as the cylinder stub is rotating, the wake contains a steady dominating inner vortex (DIV) surrounded by a secondary inner vortex. Its circumferential velocity accelerates the fluid on one side of the cylinder and decelerates it on the other side. With low rotation speed, the perturbation is initiated by a combination of elliptical and centrifugal instabilities in the near wake. At medium rotation speeds, Taylor–Couette-like streamwise vortices are generated on the decelerated side, resulting in a protruding reverse-flow zone. Results from DMD analysis and corresponding PKE analysis reveal the unstable nature of the deceleration region and the wake. At the largest rotation speed investigated, the onset of perturbations is directly located on the decelerated side of the cylinder stubs, where a deceleration mechanism feeds the instability. In the near wake, the mechanism gradually changes to a pure centrifugal instability when the rotation speed increases. In the far wake, both elliptical and centrifugal instabilities fade away, and the streaky flow featuring a vigorous DIV is then only subject to inviscid inflectional instability.
- 20 July 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 945
Open AccessTransition mechanisms in a boundary layer controlled by rotating wall-normal cylindrical roughness elements
The transition to turbulence induced by counter-rotating wall-normal rotating cylindrical roughness pairs immersed within a laminar boundary layer on a flat plate is investigated with direct numerical simulations, dynamic mode decomposition (DMD) and perturbation kinetic energy (PKE) analysis. As long as the cylinder stub is rotating, the wake contains a steady dominating inner vortex (DIV) surrounded by a secondary inner vortex. Its circumferential velocity accelerates the fluid on one side of the cylinder and decelerates it on the other side. With low rotation speed, the perturbation is initiated by a combination of elliptical and centrifugal instabilities in the near wake. At medium rotation speeds, Taylor–Couette-like streamwise vortices are generated on the decelerated side, resulting in a protruding reverse-flow zone. Results from DMD analysis and corresponding PKE analysis reveal the unstable nature of the deceleration region and the wake. At the largest rotation speed investigated, the onset of perturbations is directly located on the decelerated side of the cylinder stubs, where a deceleration mechanism feeds the instability. In the near wake, the mechanism gradually changes to a pure centrifugal instability when the rotation speed increases. In the far wake, both elliptical and centrifugal instabilities fade away, and the streaky flow featuring a vigorous DIV is then only subject to inviscid inflectional instability.
- Open Access
- 31 March 2021
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 915
Linear stability analysis of a boundary layer with rotating wall-normal cylindrical roughness elements
Cylinder stubs of finite length, mounted in a wall-normal manner on a flat plate, exert considerable control on their wake when rotating around their central axis. The present paper investigates these effects with linear stability theory and a direct numerical simulation. Three configurations are considered: evenly spaced corotating roughness elements, as well as positive and negative counter-rotating roughness pairs. Here, ‘positive’ and ‘negative’ are defined in accordance with the induced high- and low-speed streaks, respectively. A primary feature of the rotating-cylinder-induced wake is a ‘dominating inner vortex’ (DIV), which intensifies the lift-up effect and creates high-amplitude streaks. Linear stability analysis shows that the modified streaky flow is capable of effectively stabilizing Tollmien–Schlichting (TS) modes. The mechanism of TS mode stabilization, as found by a perturbation kinetic energy analysis, is attributed to the reduction of the wall-normal perturbation production. On the other hand, an inviscid inflectional instability mode related to the presence of the roughness appears which destabilizes the boundary-layer flow, primarily due to an increase in wall-normal perturbation energy production, but also due to increasing spanwise energy production, depending on the case. The inflectional instability roughness mode is more amplified with thicker cylinders since the induced DIV tends to support longer-living inflection points. Regarding an imaginable laminar–turbulent transition delay, positive rotating thinner roughness pairs would be preferable.
- 31 March 2021
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 915
Open AccessLinear stability analysis of a boundary layer with rotating wall-normal cylindrical roughness elements
Cylinder stubs of finite length, mounted in a wall-normal manner on a flat plate, exert considerable control on their wake when rotating around their central axis. The present paper investigates these effects with linear stability theory and a direct numerical simulation. Three configurations are considered: evenly spaced corotating roughness elements, as well as positive and negative counter-rotating roughness pairs. Here, ‘positive’ and ‘negative’ are defined in accordance with the induced high- and low-speed streaks, respectively. A primary feature of the rotating-cylinder-induced wake is a ‘dominating inner vortex’ (DIV), which intensifies the lift-up effect and creates high-amplitude streaks. Linear stability analysis shows that the modified streaky flow is capable of effectively stabilizing Tollmien–Schlichting (TS) modes. The mechanism of TS mode stabilization, as found by a perturbation kinetic energy analysis, is attributed to the reduction of the wall-normal perturbation production. On the other hand, an inviscid inflectional instability mode related to the presence of the roughness appears which destabilizes the boundary-layer flow, primarily due to an increase in wall-normal perturbation energy production, but also due to increasing spanwise energy production, depending on the case. The inflectional instability roughness mode is more amplified with thicker cylinders since the induced DIV tends to support longer-living inflection points. Regarding an imaginable laminar–turbulent transition delay, positive rotating thinner roughness pairs would be preferable.
- 22 April 2020
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 5 (4) , 044304
Instability and transition in an elementary porous medium
Instability and transition in an elementary porous medium are investigated via global linear stability analysis and numerical simulation. The porous medium is presented by a representative elementary volume which consists of a staggered array of square cylinders. The stability analysis indicates the first critical Reynolds number at . Two unstable modes are captured from the linear stability analysis: a two-dimensional oscillatory mode and a three-dimensional stationary mode. A series of analyses based on direct and adjoint methods is conducted on both the unstable modes. The energy analysis shows that lift-up and converging-flow effects are both responsible for the unstable modes. In the numerical simulation, the averaged fluctuation profiles exhibit spatial distributions similar to those of the perturbation kinetic energy from the three-dimensional mode, which confirms the prediction from the stability analysis. In addition, we observe stationary counterrotating streamwise vortices beginning at the subcritical Reynolds number, which is a consequence of lift-up instability.- 22 April 2020
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 5 (4) , 044304
Instability and transition in an elementary porous medium
Instability and transition in an elementary porous medium are investigated via global linear stability analysis and numerical simulation. The porous medium is presented by a representative elementary volume which consists of a staggered array of square cylinders. The stability analysis indicates the first critical Reynolds number at . Two unstable modes are captured from the linear stability analysis: a two-dimensional oscillatory mode and a three-dimensional stationary mode. A series of analyses based on direct and adjoint methods is conducted on both the unstable modes. The energy analysis shows that lift-up and converging-flow effects are both responsible for the unstable modes. In the numerical simulation, the averaged fluctuation profiles exhibit spatial distributions similar to those of the perturbation kinetic energy from the three-dimensional mode, which confirms the prediction from the stability analysis. In addition, we observe stationary counterrotating streamwise vortices beginning at the subcritical Reynolds number, which is a consequence of lift-up instability.