Yung-Chin Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yung-Chin Yang has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Hsien-Ming Kao
Department of Chemistry, National Central University, Zhongli 320317, Taiwan
14 shared publications - Diganta Saikia
Department of Chemistry, National Central University, Zhongli 320317, Taiwan
12 shared publications - Juti Rani Deka
Institute of Materials Science and Engineering, National Taipei University of Technology, Taipei 106344, Taiwan
10 shared publications Juti Rani Deka
Institute of Materials Science and Engineering, National Taipei University of Technology, Taipei 106, Taiwan, ROC
4 shared publicationsYu‐Hao Zeng
Department of Chemistry National Central University Zhongli 320317 Taiwan
4 shared publicationsCanggih Setya Budi
Department of Chemistry, National Central University, Chung-Li 32054, Taiwan, ROC
2 shared publications
Latest Publications
- Open Access
ZIF-67-Derived Co−N−C Supported Ni Nanoparticles as Efficient Recyclable Catalyst for Hydrogenation of 4-Nitrophenol
In this study, a novel, highly efficient, environment friendly, and low-cost nanocatalyst, denoted as Ni(x)@Co−N−C, was successfully developed by encapsulating Ni nanoparticles into N-doped porous carbon derived from ZIF-67. A variety of techniques including powder X-ray diffraction (XRD), nitrogen adsorption/desorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectrometer (XPS) were used to characterize the prepared materials. The TEM images reveal that the nanoparticles were distributed homogeneously in the carbon support. The N atoms in the carbon support serve as the sites for the nucleation and uniform growth of Ni nanoparticles. The catalyst was used for the degradation of environmentally harmful 4-nitrophenol (4-NP) to 4-aminophenol (4-AP). Among all the catalysts investigated, Ni(10)@Co-N-C exhibited the highest catalytic activity for the hydrogenation of 4-NP, with a specific reaction rate of 6.1 × 10−3 s−1, activity parameter of 31 s−1g−1, and turn over frequency (TOF) of 1.78 × 1019 molecules gmetal−1s−1. On the other hand, the specific reaction rate and TOF value were 1.7 × 10−3 s−1 and 6.96 × 1018 molecules gmetal−1s−1, respectively, for Co−N−C. This suggests that Ni(10)@Co−N−C is about three times more catalytically active than the Co−N−C catalyst. The superb activity of Ni(10)@Co−N−C in comparison to Co−N−C can be ascribed to the homogeneous dispersion of small-sized Ni nanoparticles, the interconnected three-dimensional porous arrangement of the support Co−N−C, the presence of N atoms in the carbon framework that stabilize metal nanoparticles, and the synergistic electronic effect between Ni and Co. The Ni(10)@Co−N−C catalyst maintained consistent catalytic activity over multiple cycles, which suggests that porous N-containing carbon support can effectively prevent aggregation and leaching of metal nanoparticles. The ICP-AES analysis of the recycled Ni(10)@Co−N−C revealed a slight reduction in metal content compared to the fresh sample, suggesting almost negligible leaching of metal nanoparticles.
Open AccessZIF-67-Derived Co−N−C Supported Ni Nanoparticles as Efficient Recyclable Catalyst for Hydrogenation of 4-Nitrophenol
In this study, a novel, highly efficient, environment friendly, and low-cost nanocatalyst, denoted as Ni(x)@Co−N−C, was successfully developed by encapsulating Ni nanoparticles into N-doped porous carbon derived from ZIF-67. A variety of techniques including powder X-ray diffraction (XRD), nitrogen adsorption/desorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectrometer (XPS) were used to characterize the prepared materials. The TEM images reveal that the nanoparticles were distributed homogeneously in the carbon support. The N atoms in the carbon support serve as the sites for the nucleation and uniform growth of Ni nanoparticles. The catalyst was used for the degradation of environmentally harmful 4-nitrophenol (4-NP) to 4-aminophenol (4-AP). Among all the catalysts investigated, Ni(10)@Co-N-C exhibited the highest catalytic activity for the hydrogenation of 4-NP, with a specific reaction rate of 6.1 × 10−3 s−1, activity parameter of 31 s−1g−1, and turn over frequency (TOF) of 1.78 × 1019 molecules gmetal−1s−1. On the other hand, the specific reaction rate and TOF value were 1.7 × 10−3 s−1 and 6.96 × 1018 molecules gmetal−1s−1, respectively, for Co−N−C. This suggests that Ni(10)@Co−N−C is about three times more catalytically active than the Co−N−C catalyst. The superb activity of Ni(10)@Co−N−C in comparison to Co−N−C can be ascribed to the homogeneous dispersion of small-sized Ni nanoparticles, the interconnected three-dimensional porous arrangement of the support Co−N−C, the presence of N atoms in the carbon framework that stabilize metal nanoparticles, and the synergistic electronic effect between Ni and Co. The Ni(10)@Co−N−C catalyst maintained consistent catalytic activity over multiple cycles, which suggests that porous N-containing carbon support can effectively prevent aggregation and leaching of metal nanoparticles. The ICP-AES analysis of the recycled Ni(10)@Co−N−C revealed a slight reduction in metal content compared to the fresh sample, suggesting almost negligible leaching of metal nanoparticles.
- Open Access
- 13 November 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (22) , 1818
Bimetallic NiCo Nanoparticles Embedded in Organic Group Functionalized Mesoporous Silica for Efficient Hydrogen Production from Ammonia Borane Hydrolysis
In this study, bimetallic NiCo nanoparticles (NPs) were encapsulated within the mesopores of carboxylic acid functionalized mesoporous silica (CMS) through the chemical reduction approach. Both NaBH4 and NH3BH3 were used as reducing agents to reduce the metal ions simultaneously. The resulting composite was used as a catalyst for hydrolysis of ammonia borane (NH3BH3, AB) to produce H2. The bimetallic NiCo NPs supported on carboxylic group functionalized mesoporous silica, referred to as NixCo100−x@CMS, exhibited significantly higher catalytic activity for AB hydrolysis compared to their monometallic counterparts. The remarkable activity of NixCo100−x@CMS could be ascribed to the synergistic contributions of Ni and Co, redox reaction during the hydrolysis, and the fine-tuned electronic structure. The catalytic performance of the NixCo100−x@CMS nanocatalyst was observed to be dependent on the composition of Ni and Co. Among all the compositions investigated, Ni40Co60@CMS demonstrated the highest catalytic activity, with a turn over frequency (TOF) of 18.95 molH2min−1molcatalyst−1 and H2 production rate of 8.0 L min−1g−1. The activity of Ni40Co60@CMS was approximately three times greater than that of Ni@CMS and about two times that of Co@CMS. The superior activity of Ni40Co60@CMS was attributed to its finely-tuned electronic structure, resulting from the electron transfer of Ni to Co. Furthermore, the nanocatalyst exhibited excellent durability, as the carboxylate group in the support provided a strong metal–support interaction, securely anchoring the NPs within the mesopores, preventing both agglomeration and leakage.
- 13 November 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (22) , 1818
Open AccessBimetallic NiCo Nanoparticles Embedded in Organic Group Functionalized Mesoporous Silica for Efficient Hydrogen Production from Ammonia Borane Hydrolysis
In this study, bimetallic NiCo nanoparticles (NPs) were encapsulated within the mesopores of carboxylic acid functionalized mesoporous silica (CMS) through the chemical reduction approach. Both NaBH4 and NH3BH3 were used as reducing agents to reduce the metal ions simultaneously. The resulting composite was used as a catalyst for hydrolysis of ammonia borane (NH3BH3, AB) to produce H2. The bimetallic NiCo NPs supported on carboxylic group functionalized mesoporous silica, referred to as NixCo100−x@CMS, exhibited significantly higher catalytic activity for AB hydrolysis compared to their monometallic counterparts. The remarkable activity of NixCo100−x@CMS could be ascribed to the synergistic contributions of Ni and Co, redox reaction during the hydrolysis, and the fine-tuned electronic structure. The catalytic performance of the NixCo100−x@CMS nanocatalyst was observed to be dependent on the composition of Ni and Co. Among all the compositions investigated, Ni40Co60@CMS demonstrated the highest catalytic activity, with a turn over frequency (TOF) of 18.95 molH2min−1molcatalyst−1 and H2 production rate of 8.0 L min−1g−1. The activity of Ni40Co60@CMS was approximately three times greater than that of Ni@CMS and about two times that of Co@CMS. The superior activity of Ni40Co60@CMS was attributed to its finely-tuned electronic structure, resulting from the electron transfer of Ni to Co. Furthermore, the nanocatalyst exhibited excellent durability, as the carboxylate group in the support provided a strong metal–support interaction, securely anchoring the NPs within the mesopores, preventing both agglomeration and leakage.
- Open Access
Fe3O4 Nanoparticle-Decorated Bimodal Porous Carbon Nanocomposite Anode for High-Performance Lithium-Ion Batteries
A new nanocomposite system based on Fe3O4 nanoparticles confined in three-dimensional (3D) dual-mode cubic porous carbon is developed using the nanocasting and wet-impregnation methods to assess its performance as an anode for lithium-ion batteries. Several Fe3O4 precursor concentrations are chosen to optimize and determine the best-performing nanocomposite composition. The cubic mesoporous carbon CMK-9 offers a better ability for the Fe3O4 nanoparticles to be accommodated inside the mesopores, efficiently buffering the variation in volume and equally enhancing electrode/electrolyte contact for rapid charge and mass transfer. Among the prepared nanocomposites, the Fe3O4(13)@C9 anode delivers an excellent reversible discharge capacity of 1222 mA h g−1 after 150 cycles at a current rate of 100 mA g−1, with a capacity retention of 96.8% compared to the fourth cycle (1262 mA h g−1). At a higher current rate of 1000 mA g−1, the nanocomposite anode offers a superior discharge capacity of 636 mA h g−1 beyond 300 cycles. The present study reveals the use of a 3D mesoporous carbon material as a scaffold for anchoring Fe3O4 nanoparticles with impressive potential as an anode for new-generation lithium-ion batteries.
Open AccessFe3O4 Nanoparticle-Decorated Bimodal Porous Carbon Nanocomposite Anode for High-Performance Lithium-Ion Batteries
A new nanocomposite system based on Fe3O4 nanoparticles confined in three-dimensional (3D) dual-mode cubic porous carbon is developed using the nanocasting and wet-impregnation methods to assess its performance as an anode for lithium-ion batteries. Several Fe3O4 precursor concentrations are chosen to optimize and determine the best-performing nanocomposite composition. The cubic mesoporous carbon CMK-9 offers a better ability for the Fe3O4 nanoparticles to be accommodated inside the mesopores, efficiently buffering the variation in volume and equally enhancing electrode/electrolyte contact for rapid charge and mass transfer. Among the prepared nanocomposites, the Fe3O4(13)@C9 anode delivers an excellent reversible discharge capacity of 1222 mA h g−1 after 150 cycles at a current rate of 100 mA g−1, with a capacity retention of 96.8% compared to the fourth cycle (1262 mA h g−1). At a higher current rate of 1000 mA g−1, the nanocomposite anode offers a superior discharge capacity of 636 mA h g−1 beyond 300 cycles. The present study reveals the use of a 3D mesoporous carbon material as a scaffold for anchoring Fe3O4 nanoparticles with impressive potential as an anode for new-generation lithium-ion batteries.
- 19 September 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (12)
Development of a New Crosslinked Highly Conductive Hybrid Electrolyte based on Polyetherdiamine, Diphenylmethane Diisocyanate and Organosilanes for Efficient Lithium‐Metal Battery
In this study, a new crosslinked organic‐inorganic hybrid polymer electrolyte membrane is developed by first reacting polyetherdiamine with diphenylmethane diisocyanate, followed by addition of organosilane precursors 3‐(glycidyloxypropyl) trimethoxysilane and 2‐[methoxy(polyethyleneoxy) propyl] trimethoxysilane and LiClO4 salt. Various characterization methods are employed to probe the crystallinity behavior, morphology, ionic interactions, thermal stability, architectural durability and dynamic performance of the hybrid solid polymer electrolyte (HSPE) membranes. Among the electrolytes, the HSPE membrane with [EO]/[Li] ratio of 32 delivers the excellent ionic conductivity value of 1.2×10−4 S cm−1 at 30 °C. When the hybrid membrane without salt is plasticized with various electrolyte solvents, the ionic conductivity enhances significantly to values in the range of 1.2 to 1.8×10−3 S cm−1 at 30 °C. The lithium metal battery (LMB) assembled with the gel polymer electrolyte (GPE), lithium anode and LiFePO4 cathode provides excellent rate and cycle performances. The LMB delivers very stable discharge capacity of 121.1 mAh g−1 after 150 cycles at the rate of 0.1 C with 97.6 % capacity holding compared to first cycle and exhibits above 99 % Coulombic efficiency values. The present crosslinked hybrid polymer electrolytes are potentially promising for the future development of high performance lithium‐metal batteries.
- 19 September 2022
- Published by Wiley in Batteries & Supercaps
- Vol. 5 (12)
Development of a New Crosslinked Highly Conductive Hybrid Electrolyte based on Polyetherdiamine, Diphenylmethane Diisocyanate and Organosilanes for Efficient Lithium‐Metal Battery
In this study, a new crosslinked organic‐inorganic hybrid polymer electrolyte membrane is developed by first reacting polyetherdiamine with diphenylmethane diisocyanate, followed by addition of organosilane precursors 3‐(glycidyloxypropyl) trimethoxysilane and 2‐[methoxy(polyethyleneoxy) propyl] trimethoxysilane and LiClO4 salt. Various characterization methods are employed to probe the crystallinity behavior, morphology, ionic interactions, thermal stability, architectural durability and dynamic performance of the hybrid solid polymer electrolyte (HSPE) membranes. Among the electrolytes, the HSPE membrane with [EO]/[Li] ratio of 32 delivers the excellent ionic conductivity value of 1.2×10−4 S cm−1 at 30 °C. When the hybrid membrane without salt is plasticized with various electrolyte solvents, the ionic conductivity enhances significantly to values in the range of 1.2 to 1.8×10−3 S cm−1 at 30 °C. The lithium metal battery (LMB) assembled with the gel polymer electrolyte (GPE), lithium anode and LiFePO4 cathode provides excellent rate and cycle performances. The LMB delivers very stable discharge capacity of 121.1 mAh g−1 after 150 cycles at the rate of 0.1 C with 97.6 % capacity holding compared to first cycle and exhibits above 99 % Coulombic efficiency values. The present crosslinked hybrid polymer electrolytes are potentially promising for the future development of high performance lithium‐metal batteries.
- 16 August 2022
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (15) , 22454-22473
New insights into the outstanding performances of nickel‐doped manganese oxide nanoparticles embedded in a 3D carbon nanopipes framework as anode for lithium and sodium‐ion batteries
- 16 August 2022
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (15) , 22454-22473
New insights into the outstanding performances of nickel‐doped manganese oxide nanoparticles embedded in a 3D carbon nanopipes framework as anode for lithium and sodium‐ion batteries
- Open Access
- 15 December 2021
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (5) , 6919-6928
Effect of nanowire conductive transfer on the performance of batch‐microbial fuel cells
- 15 December 2021
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (5) , 6919-6928
Open AccessEffect of nanowire conductive transfer on the performance of batch‐microbial fuel cells
- Open Access
- 20 May 2020
- Published by Wiley in ChemSusChem
- Vol. 13 (11) , 2805
Cover Feature: Insight into the Superior Lithium Storage Properties of Ultrafine CoO Nanoparticles Confined in a 3 D Bimodal Ordered Mesoporous Carbon CMK‐9 Anode (ChemSusChem 11/2020)
- 20 May 2020
- Published by Wiley in ChemSusChem
- Vol. 13 (11) , 2805
Open AccessCover Feature: Insight into the Superior Lithium Storage Properties of Ultrafine CoO Nanoparticles Confined in a 3 D Bimodal Ordered Mesoporous Carbon CMK‐9 Anode (ChemSusChem 11/2020)
- 30 April 2020
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 8 (2) , 024005
Tribological and mechanical properties of Cu/Ni-microdiamond bilayers on brass substrates coated by composite electrodeposition technology
Currently thin-plate glass used in portable devices is initially segmented by laser beam. The material melts and vaporizes during the process, which requires micro-tools for further edge milling. Due to the poor wear resistance and short life of the micro-milling tools and the fragile nature of the glass, the processing cost is high due to the low yield. In this study, a new alternative for preparing micron diamond milling tools was reported. Bilayers on brass substrates by a composite electrodeposition technique was prepared by using diamonds with a diameter of 2–4 μ m. In order to improve the adhesion between the coating and the substrate, the electroplated pure copper was coated as the bottom layer, then the nickel and the diamond were compositely electrodeposited. The effects of current density, stirring speed, and diamond concentration in the electrolyte on the mechanical properties of the coating were investigated. The content and distribution of the incorporated diamond were analyzed by electron microscopy. It was found that, with the increase of current density, stirring speed, and the concentration of diamond in the electrolyte, the diamond content of the coating increased first and then decreased. When the parameters were: 200 rpm, 1.33 A dm −2 , 10 g l −1 , the content of the incorporated diamond in the coating became the densest and most uniform one, which enhanced the hardness and the wear resistance of the coating and reduced the roughness of the workpiece. The result of the wear test indicated that no coating composition was transferred to the glass ball, which meant the coating did not contaminate the glass material. The unique press-in mechanism protected the pull-off of the diamond and prolonged the tool’s service life. The rebounding mechanism of the coating was also feasible to the machining process of the glass, which could avoid the fragment of the thin glass. The use of the composite electrodeposition technique can remarkly reduce the manufacture cost of the micro-milling tool and, in the mean time, improve the machininng efficency and quality of hard and fragile materials.
- 30 April 2020
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 8 (2) , 024005
Tribological and mechanical properties of Cu/Ni-microdiamond bilayers on brass substrates coated by composite electrodeposition technology
Currently thin-plate glass used in portable devices is initially segmented by laser beam. The material melts and vaporizes during the process, which requires micro-tools for further edge milling. Due to the poor wear resistance and short life of the micro-milling tools and the fragile nature of the glass, the processing cost is high due to the low yield. In this study, a new alternative for preparing micron diamond milling tools was reported. Bilayers on brass substrates by a composite electrodeposition technique was prepared by using diamonds with a diameter of 2–4 μ m. In order to improve the adhesion between the coating and the substrate, the electroplated pure copper was coated as the bottom layer, then the nickel and the diamond were compositely electrodeposited. The effects of current density, stirring speed, and diamond concentration in the electrolyte on the mechanical properties of the coating were investigated. The content and distribution of the incorporated diamond were analyzed by electron microscopy. It was found that, with the increase of current density, stirring speed, and the concentration of diamond in the electrolyte, the diamond content of the coating increased first and then decreased. When the parameters were: 200 rpm, 1.33 A dm −2 , 10 g l −1 , the content of the incorporated diamond in the coating became the densest and most uniform one, which enhanced the hardness and the wear resistance of the coating and reduced the roughness of the workpiece. The result of the wear test indicated that no coating composition was transferred to the glass ball, which meant the coating did not contaminate the glass material. The unique press-in mechanism protected the pull-off of the diamond and prolonged the tool’s service life. The rebounding mechanism of the coating was also feasible to the machining process of the glass, which could avoid the fragment of the thin glass. The use of the composite electrodeposition technique can remarkly reduce the manufacture cost of the micro-milling tool and, in the mean time, improve the machininng efficency and quality of hard and fragile materials.
- Open Access
Ru Nanoparticles Embedded in Cubic Mesoporous Silica SBA-1 as Highly Efficient Catalysts for Hydrogen Generation from Ammonia Borane
Cubic mesoporous silica SBA-1 functionalized with carboxylic acid (-COOH), namely S1B-C10, is used as a support to fabricate and confine Ru nanoparticles (NPs). The uniformly dispersed organic functional groups in SBA-1 are beneficial in attracting Ru cations, and as a result, homogenously distributed small sized Ru NPs are formed within the mesopores. The prepared Ru@S1B-C10 is utilized as a catalyst for H2 generation from the hydrolysis of ammonia borane (AB). The Ru@S1B-C10 catalyst demonstrates high catalytic activity for H2 generation (202 mol H2 molRu min−1) and lower activation energy (24.13 kJ mol−1) due to the small sized Ru NPs with high dispersion and the support’s interconnected mesoporous structure. The nanosized Ru particles provide abundant active sites for the catalytic reaction to take place, while the interconnected porous support facilitates homogenous transference and easy dispersal of AB molecules to the active sites. The catalyst demonstrates good recycle ability since the accumulation and leaking of NPs throughout catalysis can be effectively prevented by the support.
Open AccessRu Nanoparticles Embedded in Cubic Mesoporous Silica SBA-1 as Highly Efficient Catalysts for Hydrogen Generation from Ammonia Borane
Cubic mesoporous silica SBA-1 functionalized with carboxylic acid (-COOH), namely S1B-C10, is used as a support to fabricate and confine Ru nanoparticles (NPs). The uniformly dispersed organic functional groups in SBA-1 are beneficial in attracting Ru cations, and as a result, homogenously distributed small sized Ru NPs are formed within the mesopores. The prepared Ru@S1B-C10 is utilized as a catalyst for H2 generation from the hydrolysis of ammonia borane (AB). The Ru@S1B-C10 catalyst demonstrates high catalytic activity for H2 generation (202 mol H2 molRu min−1) and lower activation energy (24.13 kJ mol−1) due to the small sized Ru NPs with high dispersion and the support’s interconnected mesoporous structure. The nanosized Ru particles provide abundant active sites for the catalytic reaction to take place, while the interconnected porous support facilitates homogenous transference and easy dispersal of AB molecules to the active sites. The catalyst demonstrates good recycle ability since the accumulation and leaking of NPs throughout catalysis can be effectively prevented by the support.