Rafic G. El-Helou
Rafic G. El-Helou has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Benjamin A. Graybeal
Turner-Fairbank Highway Research Center
6 shared publications Cristopher D. Moen
F.SEI, Chief Executive Officer, RunToSolve, Limited Liability Company, 2 Smeton Place, Unit C, Towson, MD 21204
1 shared publication- Igor De la Varga
SES Group and Associates
1 shared publication Ioannis Koutromanos
Associate Professor, Dept. of Civil and Environmental Engineering, Virginia Polytechnic Institute and State Univ., Blacksburg, VA 24061
1 shared publication- Mohammadreza Moharrami
Staff II Engineer, Simpson Gumpertz and Heger, Inc., 41 Seyon St. Bldg. 1, Suite 500, Waltham, MA 02453. ORCID:
1 shared publication - Robert P. Spragg
SES Group and Associates
1 shared publication
Latest Publications
- Open Access
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 149 (2) , 04022234
Shear Design of Strain-Hardening Fiber-Reinforced Concrete Beams
Strain-hardening fiber-reinforced concrete (SH-FRC), such as ultrahigh-performance concrete (UHPC), offers sustained tensile capacities up to high values of postcracking strains and, consequently, delivers shear resistance through different mechanisms than conventional concrete. Existing shear design methods for conventional concrete beams include empirical approximations of the tensile resistance offered by the cracked concrete that do not apply to SH-FRC materials. This article presents a design formulation that predicts the shear capacity of SH-FRC beams in support of ongoing efforts to develop UHPC structural design guidance in the United States. The proposed model leverages foundational concepts from engineering mechanics, similar to the modified compression-field theory (MCFT) for conventional reinforced and prestressed concrete, while integrating relationships that address behaviors specific to SH-FRC. The model predicts shear stress versus shear strain behavior of a cracked SH-FRC membrane element, which is then used to model the web of a beam. Verified against experimental shear test results of I-shaped prestressed and non-prestressed beams with different material properties, beam geometries, axial strains, and transverse reinforcement ratios, the proposed shear design model is demonstrated to conservatively predict the shear capacity of SH-FRC beams. As such, this work constitutes a fundamental step in developing mechanics-based SH-FRC shear design guidance.
- 1 February 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 149 (2) , 04022234
Open AccessShear Design of Strain-Hardening Fiber-Reinforced Concrete Beams
Strain-hardening fiber-reinforced concrete (SH-FRC), such as ultrahigh-performance concrete (UHPC), offers sustained tensile capacities up to high values of postcracking strains and, consequently, delivers shear resistance through different mechanisms than conventional concrete. Existing shear design methods for conventional concrete beams include empirical approximations of the tensile resistance offered by the cracked concrete that do not apply to SH-FRC materials. This article presents a design formulation that predicts the shear capacity of SH-FRC beams in support of ongoing efforts to develop UHPC structural design guidance in the United States. The proposed model leverages foundational concepts from engineering mechanics, similar to the modified compression-field theory (MCFT) for conventional reinforced and prestressed concrete, while integrating relationships that address behaviors specific to SH-FRC. The model predicts shear stress versus shear strain behavior of a cracked SH-FRC membrane element, which is then used to model the web of a beam. Verified against experimental shear test results of I-shaped prestressed and non-prestressed beams with different material properties, beam geometries, axial strains, and transverse reinforcement ratios, the proposed shear design model is demonstrated to conservatively predict the shear capacity of SH-FRC beams. As such, this work constitutes a fundamental step in developing mechanics-based SH-FRC shear design guidance.
- Open Access
- 1 April 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (4) , 04022017
Shear Behavior of Ultrahigh-Performance Concrete Pretensioned Bridge Girders
Because of their tensile strain-hardening characteristics, ultrahigh-performance concrete (UHPC) materials offer significant advantages in terms of beam shear capacity and postcracking behavior compared to conventional reinforced-concrete beams. These advantages rely on UHPC’s ability to sustain its strain-hardening characteristics at the structural level. This paper reports the results of an experimental investigation on the parameters influencing the structural shear behavior of prestressed UHPC bridge girders. Six pretensioned bulb-tee UHPC bridge girders were tested in shear with the following test variables: the UHPC material properties, the girder height, the web thickness, the number of prestressing strands, and the presence of discrete transverse steel reinforcement in the web. The average relationship between the principal stress and strains in the web was monitored during the tests and compared to behavior obtained from uniaxial tests. The shear behavior and capacities of the tested girders were observed to be largely dependent on the tensile characteristics of UHPC. The results demonstrate UHPC’s capability to sustain its strain-hardening characteristics at the structural scale and highlight the importance of the crack localization strain, corresponding to the end of the tensile hardening behavior, to the global shear performance of UHPC girders.
- 1 April 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (4) , 04022017
Open AccessShear Behavior of Ultrahigh-Performance Concrete Pretensioned Bridge Girders
Because of their tensile strain-hardening characteristics, ultrahigh-performance concrete (UHPC) materials offer significant advantages in terms of beam shear capacity and postcracking behavior compared to conventional reinforced-concrete beams. These advantages rely on UHPC’s ability to sustain its strain-hardening characteristics at the structural level. This paper reports the results of an experimental investigation on the parameters influencing the structural shear behavior of prestressed UHPC bridge girders. Six pretensioned bulb-tee UHPC bridge girders were tested in shear with the following test variables: the UHPC material properties, the girder height, the web thickness, the number of prestressing strands, and the presence of discrete transverse steel reinforcement in the web. The average relationship between the principal stress and strains in the web was monitored during the tests and compared to behavior obtained from uniaxial tests. The shear behavior and capacities of the tested girders were observed to be largely dependent on the tensile characteristics of UHPC. The results demonstrate UHPC’s capability to sustain its strain-hardening characteristics at the structural scale and highlight the importance of the crack localization strain, corresponding to the end of the tensile hardening behavior, to the global shear performance of UHPC girders.
- Open Access
- 1 April 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (4) , 04022013
Flexural Behavior and Design of Ultrahigh-Performance Concrete Beams
Beams made of ultrahigh-performance concrete (UHPC), a fiber-reinforced concrete with high compressive strength and tensile strain-hardening characteristics, exhibit flexural behaviors that are different than those traditionally associated with steel-reinforced conventional concrete beams. These behaviors necessitate the development of new predictive design tools that reflect the effect of the material-level properties on the flexural behavior. The research presented in this paper assessed the flexural behavior of UHPC beams through the displacement-controlled testing of a prestressed UHPC bridge girder to failure. The girder was 18.90 m (62 ft) long and contained a total of 26 17.8-mm- (0.7-in.)-diameter steel strands and no mild steel reinforcement. The testing focused on capturing the intermediate and final behaviors, including first cracking, yielding of strands, moment capacity at the development of a single dominant crack, and rupture of strands. Building on observations from this study and prior research by the authors and others, a flexural design framework, founded on the concepts of equilibrium and strain compatibility, is proposed for beams made with UHPC and reinforced with conventional steel reinforcing bars, prestressing strands, or both. The proposed framework includes considerations to avoid the local straining and subsequent hinging of UHPC beams and to address the ductility of flexural members. The framework is verified by comparing the experimental results of flexural tests performed by the authors and others to the analytical predictions, which predominantly relied on input material parameters obtained from independent material tests.
- 1 April 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 148 (4) , 04022013
Open AccessFlexural Behavior and Design of Ultrahigh-Performance Concrete Beams
Beams made of ultrahigh-performance concrete (UHPC), a fiber-reinforced concrete with high compressive strength and tensile strain-hardening characteristics, exhibit flexural behaviors that are different than those traditionally associated with steel-reinforced conventional concrete beams. These behaviors necessitate the development of new predictive design tools that reflect the effect of the material-level properties on the flexural behavior. The research presented in this paper assessed the flexural behavior of UHPC beams through the displacement-controlled testing of a prestressed UHPC bridge girder to failure. The girder was 18.90 m (62 ft) long and contained a total of 26 17.8-mm- (0.7-in.)-diameter steel strands and no mild steel reinforcement. The testing focused on capturing the intermediate and final behaviors, including first cracking, yielding of strands, moment capacity at the development of a single dominant crack, and rupture of strands. Building on observations from this study and prior research by the authors and others, a flexural design framework, founded on the concepts of equilibrium and strain compatibility, is proposed for beams made with UHPC and reinforced with conventional steel reinforcing bars, prestressing strands, or both. The proposed framework includes considerations to avoid the local straining and subsequent hinging of UHPC beams and to address the ductility of flexural members. The framework is verified by comparing the experimental results of flexural tests performed by the authors and others to the analytical predictions, which predominantly relied on input material parameters obtained from independent material tests.
- 2 June 2019
- Published by Iowa State University
- Vol. 2 (1)
The Ultra Girder: A Design Concept for a 300-foot Single Span Prestressed Ultra-High Performance Concrete Bridge Girder
- 2 June 2019
- Published by Iowa State University
- Vol. 2 (1)
The Ultra Girder: A Design Concept for a 300-foot Single Span Prestressed Ultra-High Performance Concrete Bridge Girder
- 2 June 2019
- Published by Iowa State University
- Vol. 2 (1)
Development of an AASHTO Guide Specification for UHPC
- 2 June 2019
- Published by Iowa State University
- Vol. 2 (1)
Development of an AASHTO Guide Specification for UHPC