Christian Kastl
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Christian Kastl has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Markus Pichler-Scheder
Linz Center of Mechatronics, Linz, Austria
4 shared publications - Andreas Stelzer
Institute for Communications Engineering and RF-Systems, Johannes Kepler University Linz, Linz, Austria
2 shared publications - Florian Hammer
Linz Center of Mechatronics GmbH, Linz, Austria
2 shared publications - Martin Scherhaufl
Department of Sensors and Communication, Linz Center of Mechatronics GmbH, Linz, Austria
2 shared publications - Veronika Putz
Linz Center of Mechatronics GmbH, Austria
2 shared publications - Andreas Springer
Institute for Communications Engineering and RF-Systems, Johannes Kepler University, Linz, Austria
1 shared publication
Latest Publications
- 25 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
Viterbi Decoder to Resolve Angular Ambiguity in Digital Beamforming With Widely Spaced Radar Front Ends
This article introduces a precise radar-based direction-of-arrival measurement system using a Viterbi decoder. Based on the frequency-modulated continuous-wave principle, the presented method employs both the frequency difference and the round-trip phase difference of the radio wave signal impinging at two widely spaced receiving antennas, thereby accomplishing highly accurate and absolute measurements of the direction-of-arrival. In order to resolve angular ambiguity, which is inherently caused by the 2π ambiguity in phase measurement, the proposed Viterbi decoder determines the most likely sequence of direction-of-arrivals of the impinging radio wave signals. For proof of concept, experiments based on a 77 GHz radar unit equipped with one transmitting and two widely spaced receiving antennas were carried out. The measurement results show that angular ambiguity can be resolved by the presented Viterbi decoder since absolute, accurate, and repeatable direction-of-arrival estimates were obtained, even for receiver antenna spacings significantly larger than the signal wavelength.
- 25 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-9
Viterbi Decoder to Resolve Angular Ambiguity in Digital Beamforming With Widely Spaced Radar Front Ends
This article introduces a precise radar-based direction-of-arrival measurement system using a Viterbi decoder. Based on the frequency-modulated continuous-wave principle, the presented method employs both the frequency difference and the round-trip phase difference of the radio wave signal impinging at two widely spaced receiving antennas, thereby accomplishing highly accurate and absolute measurements of the direction-of-arrival. In order to resolve angular ambiguity, which is inherently caused by the 2π ambiguity in phase measurement, the proposed Viterbi decoder determines the most likely sequence of direction-of-arrivals of the impinging radio wave signals. For proof of concept, experiments based on a 77 GHz radar unit equipped with one transmitting and two widely spaced receiving antennas were carried out. The measurement results show that angular ambiguity can be resolved by the presented Viterbi decoder since absolute, accurate, and repeatable direction-of-arrival estimates were obtained, even for receiver antenna spacings significantly larger than the signal wavelength.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1161-1166
Detecting wear in internal gear pumps by observing the pressure reduction time
In this paper, we propose a novel feature extraction approach for detecting wear in internal gear pumps. In a data-driven approach, the pressure reduction time (PRT) was identified as a useful feature for wear detection. It measures the time for reducing the internal pump pressure from one certain level to another when the pump engine is stopped and the valves are closed. The PRT can thus be interpreted as an internal leakage factor of the pump. When the internal leakage increases due to wear, the pressure in the pump decreases faster (implying a decreased PRT). The proposed approach has been developed and tested with data of real internal gear pumps with different operating times. The PRT shows a close relation to the operating time of the pump. Moreover, we compared PRT with the two well known approaches pressure holding speed (PHS) and head flow diagram (HFD). Especially for medium operating times of a pump, PRT shows better sensitivity than PHS and HFD.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1161-1166
Detecting wear in internal gear pumps by observing the pressure reduction time
In this paper, we propose a novel feature extraction approach for detecting wear in internal gear pumps. In a data-driven approach, the pressure reduction time (PRT) was identified as a useful feature for wear detection. It measures the time for reducing the internal pump pressure from one certain level to another when the pump engine is stopped and the valves are closed. The PRT can thus be interpreted as an internal leakage factor of the pump. When the internal leakage increases due to wear, the pressure in the pump decreases faster (implying a decreased PRT). The proposed approach has been developed and tested with data of real internal gear pumps with different operating times. The PRT shows a close relation to the operating time of the pump. Moreover, we compared PRT with the two well known approaches pressure holding speed (PHS) and head flow diagram (HFD). Especially for medium operating times of a pump, PRT shows better sensitivity than PHS and HFD.
- 22 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (9) , 3784-3793
Radar Distance Measurement With Viterbi Algorithm to Resolve Phase Ambiguity
In this article, a precise phase-based radar distance measurement system using a Viterbi decoder to resolve phase ambiguity is presented. Relying on the frequency-modulated continuous-wave radar principle, the introduced method evaluates both the frequency and the phase of the intermediate frequency signal, thus achieving absolute distance measurement with high accuracy. To avoid ambiguity in the distance estimates by half the wavelength of the radio frequency signal, which commonly arises due to 2 π ambiguity in the measurement of the phase, the proposed Viterbi-based method estimates the most likely sequence of distances between the radar front end and the target. To verify the system concept, measurements using a commercial 77 GHz radar module were carried out, whereby the contour of a predefined surface containing steps in the height profile had to be determined. The experimental results confirm that the Viterbi-based approach is suitable to resolve phase ambiguity since accurate and repeatable distance estimates were obtained.
- 22 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (9) , 3784-3793
Radar Distance Measurement With Viterbi Algorithm to Resolve Phase Ambiguity
In this article, a precise phase-based radar distance measurement system using a Viterbi decoder to resolve phase ambiguity is presented. Relying on the frequency-modulated continuous-wave radar principle, the introduced method evaluates both the frequency and the phase of the intermediate frequency signal, thus achieving absolute distance measurement with high accuracy. To avoid ambiguity in the distance estimates by half the wavelength of the radio frequency signal, which commonly arises due to 2 π ambiguity in the measurement of the phase, the proposed Viterbi-based method estimates the most likely sequence of distances between the radar front end and the target. To verify the system concept, measurements using a commercial 77 GHz radar module were carried out, whereby the contour of a predefined surface containing steps in the height profile had to be determined. The experimental results confirm that the Viterbi-based approach is suitable to resolve phase ambiguity since accurate and repeatable distance estimates were obtained.
- 13 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (9) , 6016-6029
Discrete- and Continuous-State Trajectory Decoders for Positioning in Wireless Networks
The need for accurate positioning and tracking of mobile sensor nodes arises in many applications. To compute position estimates from raw measurements in positioning systems, Bayesian filtering techniques such as Kalman, histogram, or particle filters are frequently employed. A major disadvantage of these techniques is the fact that they compute only a single position estimate in every timestep, and therefore do not utilize the available information to full extent. The work presented in this paper improves over this current state of the art by instead estimating full node trajectories, and therefore, the most plausible sequence of positions in every timestep. We present two distinct algorithms—for a discrete and for a continuous state-space—and highlight the particular advantages of each variant. Achievable results are shown by simulation and measurement to be more accurate than the traditional Bayesian filtering approach. The most prominent advantage of much more accurate total track length estimation is particularly emphasized.
- 13 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (9) , 6016-6029
Discrete- and Continuous-State Trajectory Decoders for Positioning in Wireless Networks
The need for accurate positioning and tracking of mobile sensor nodes arises in many applications. To compute position estimates from raw measurements in positioning systems, Bayesian filtering techniques such as Kalman, histogram, or particle filters are frequently employed. A major disadvantage of these techniques is the fact that they compute only a single position estimate in every timestep, and therefore do not utilize the available information to full extent. The work presented in this paper improves over this current state of the art by instead estimating full node trajectories, and therefore, the most plausible sequence of positions in every timestep. We present two distinct algorithms—for a discrete and for a continuous state-space—and highlight the particular advantages of each variant. Achievable results are shown by simulation and measurement to be more accurate than the traditional Bayesian filtering approach. The most prominent advantage of much more accurate total track length estimation is particularly emphasized.
- Open Access
- 1 January 2020
- Published by AMA Service GmbH
- p. 31-37
1.2 Evaluation of Energy Harvesting Devices for Industrial Applications
- 1 January 2020
- Published by AMA Service GmbH
- p. 31-37
Open Access1.2 Evaluation of Energy Harvesting Devices for Industrial Applications