Xixing Wen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xixing Wen has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
Toh-Ming Lu
Center for Materials, Devices and Integrated Systems, Department of Physics, Applied Physics and Astronomy, Rensselaer Polytechnic Institute, Troy, New York 12180, United States
9 shared publications- Zonghuan Lu
Center for Materials, Devices, and Integrated Systems (CMDIS), Rensselaer Polytechnic Institute 2 , Troy, New York 12180
7 shared publications Gwo-Ching Wang
Center for Materials, Devices and Integrated Systems, Department of Physics, Applied Physics and Astronomy, Rensselaer Polytechnic Institute, Troy, New York 12180, United States
6 shared publicationsWugang Liao
5 shared publications- Chao Chen
Huazhong University of Science and Technology
4 shared publications - Jian Shi
Department of Materials Science and Engineering Rensselaer Polytechnic Institute Troy New York USA
4 shared publications
Latest Publications
- 5 November 2026
- Published by Wiley in Advanced Materials
In Situ Bulk Passivation and Carrier Transport Modulation in Te‐TeO x Films Enable Low‐Noise Monolithic Near‐Infrared Imagers
Near‐infrared (NIR) imagers are essential for applications ranging from material sorting and autonomous driving to biomedical diagnostics, yet their performance is often limited by severe carrier recombination and high dark current. Here, we demonstrate a low‐noise NIR photodiode based on Te‐TeO x nanocrystalline‐in‐matrix films, in which the surrounding oxide matrix provides in situ bulk passivation and enables the modulation of carrier transport to balance carrier loss and extraction. This approach reduces trap density, suppresses recombination, and prolongs carrier lifetime, while controlled oxide incorporation tunes the optical bandgap and interfacial offsets of the heterojunction photodiode, resulting in spectral response spanning the visible and NIR regions with low dark current. The resulting photodiodes exhibit a low dark current of 9.70 nA cm −2 at a bias of −10 mV, a detectivity of 3.85 × 10 12 Jones and an ultralow detectable power of 1.35 pW for NIR photodetection. The strategy is compatible with direct monolithic integration with readout integrated circuits, enabling a 256 × 256 focal‐plane imager with excellent pixel uniformity. It further supports high‐quality focal‐plane imaging in both visible and NIR regions, as well as solution identification and imaging through smoke.
- 5 November 2026
- Published by Wiley in Advanced Materials
In Situ Bulk Passivation and Carrier Transport Modulation in Te‐TeO x Films Enable Low‐Noise Monolithic Near‐Infrared Imagers
Near‐infrared (NIR) imagers are essential for applications ranging from material sorting and autonomous driving to biomedical diagnostics, yet their performance is often limited by severe carrier recombination and high dark current. Here, we demonstrate a low‐noise NIR photodiode based on Te‐TeO x nanocrystalline‐in‐matrix films, in which the surrounding oxide matrix provides in situ bulk passivation and enables the modulation of carrier transport to balance carrier loss and extraction. This approach reduces trap density, suppresses recombination, and prolongs carrier lifetime, while controlled oxide incorporation tunes the optical bandgap and interfacial offsets of the heterojunction photodiode, resulting in spectral response spanning the visible and NIR regions with low dark current. The resulting photodiodes exhibit a low dark current of 9.70 nA cm −2 at a bias of −10 mV, a detectivity of 3.85 × 10 12 Jones and an ultralow detectable power of 1.35 pW for NIR photodetection. The strategy is compatible with direct monolithic integration with readout integrated circuits, enabling a 256 × 256 focal‐plane imager with excellent pixel uniformity. It further supports high‐quality focal‐plane imaging in both visible and NIR regions, as well as solution identification and imaging through smoke.
Aluminum Doping and Nanocolumnar Structure Enable Dark‐Current Suppressed PbS Nanocrystalline Photodiode for Near‐Infrared Detection and Imaging
Near‐Infrared (NIR) detectors are crucial for applications like autonomous driving, food safety, and disease diagnosis. However, conventional photodetectors rely on complex epitaxial processes and costly single‐crystalline substrates yet still suffer from high dark current and limited detection performance at room temperature. Many of these detectors require deep cooling to mitigate dark current and suppress random fluctuations induced by carrier thermal excitation. Herein, an exceptionally low‐dark‐current is presented, self‐powered NIR photodiode detector based on a solution‐processed PbS nanocrystalline film and its CdS/PbS heterojunction. The photodiode offers the state‐of‐the‐art dark current density of 20 nA cm⁻ 2 (−10 mV bias) at room temperature, much lower than some PbS commercial photodetectors. It also exhibits a high detectivity of 7.98 × 10 11 Jones under total noise, a responsivity of 130 mA W⁻¹ and a wide linear dynamic range of 84 dB for 970 nm illumination at 0 V bias. These improved performances are attributed to the interfacial energy band engineering through aluminum doping and the enhanced photocarrier collection by nanocolumnar structure of the device. Furthermore, this study demonstrates the capability of the PbS photodiode for NIR imaging, opening a new avenue for the development of high‐sensitivity NIR photodetector and imaging at room temperature.
Aluminum Doping and Nanocolumnar Structure Enable Dark‐Current Suppressed PbS Nanocrystalline Photodiode for Near‐Infrared Detection and Imaging
Near‐Infrared (NIR) detectors are crucial for applications like autonomous driving, food safety, and disease diagnosis. However, conventional photodetectors rely on complex epitaxial processes and costly single‐crystalline substrates yet still suffer from high dark current and limited detection performance at room temperature. Many of these detectors require deep cooling to mitigate dark current and suppress random fluctuations induced by carrier thermal excitation. Herein, an exceptionally low‐dark‐current is presented, self‐powered NIR photodiode detector based on a solution‐processed PbS nanocrystalline film and its CdS/PbS heterojunction. The photodiode offers the state‐of‐the‐art dark current density of 20 nA cm⁻ 2 (−10 mV bias) at room temperature, much lower than some PbS commercial photodetectors. It also exhibits a high detectivity of 7.98 × 10 11 Jones under total noise, a responsivity of 130 mA W⁻¹ and a wide linear dynamic range of 84 dB for 970 nm illumination at 0 V bias. These improved performances are attributed to the interfacial energy band engineering through aluminum doping and the enhanced photocarrier collection by nanocolumnar structure of the device. Furthermore, this study demonstrates the capability of the PbS photodiode for NIR imaging, opening a new avenue for the development of high‐sensitivity NIR photodetector and imaging at room temperature.
- 10 January 2025
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 16 (3) , 682-695
Highly Thermal-Conductive Cubic Boron Arsenide: Single-Crystal Growth, Properties, and Future Thin-Film Epitaxy
Heat dissipation has become a critical challenge in modern electronics, driving the need for a revolution in thermal management strategies beyond traditional packaging materials, thermal interface materials, and heat sinks. Cubic boron arsenide (c-BAs) offers a promising solution, thanks to its combination of high thermal conductivity and high ambipolar mobility, making it highly suitable for applications in both electronic devices and thermal management. However, challenges remain, particularly in the large-scale synthesis of a high-quality material and the tuning of its physical properties. This Perspective reviews key research on c-BAs and discusses the future potential of van der Waals (vdW) epitaxy and remote epitaxy for preparing high-quality c-BAs thin-films. Based on superlattice area mismatch calculations, we predict some potential substrates for these epitaxy techniques. Three important design considerations for future vdW or remote epitaxy of c-BAs thin-films are identified: superlattice matching at the heterointerface, the kinetics of B and As adatoms, and the surface modification of vdW or vdW/3D substrates.
- 10 January 2025
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry Letters
- Vol. 16 (3) , 682-695
Highly Thermal-Conductive Cubic Boron Arsenide: Single-Crystal Growth, Properties, and Future Thin-Film Epitaxy
Heat dissipation has become a critical challenge in modern electronics, driving the need for a revolution in thermal management strategies beyond traditional packaging materials, thermal interface materials, and heat sinks. Cubic boron arsenide (c-BAs) offers a promising solution, thanks to its combination of high thermal conductivity and high ambipolar mobility, making it highly suitable for applications in both electronic devices and thermal management. However, challenges remain, particularly in the large-scale synthesis of a high-quality material and the tuning of its physical properties. This Perspective reviews key research on c-BAs and discusses the future potential of van der Waals (vdW) epitaxy and remote epitaxy for preparing high-quality c-BAs thin-films. Based on superlattice area mismatch calculations, we predict some potential substrates for these epitaxy techniques. Three important design considerations for future vdW or remote epitaxy of c-BAs thin-films are identified: superlattice matching at the heterointerface, the kinetics of B and As adatoms, and the surface modification of vdW or vdW/3D substrates.
- 16 December 2024
- Published by Springer Nature in Science China Chemistry
- Vol. 68 (2) , 409-410
In-situ formation of a new cation renders perovskite solar modules with a record efficiency and long-term stability
- 16 December 2024
- Published by Springer Nature in Science China Chemistry
- Vol. 68 (2) , 409-410
In-situ formation of a new cation renders perovskite solar modules with a record efficiency and long-term stability
- 26 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (18) , 22251-22262
Vertically Aligned One-Dimensional Crystal-Structured Sb2Se3 for High-Efficiency Flexible Solar Cells via Regulating Selenization Kinetics
Recently, antimony selenide (Sb2Se3) has exhibited an exciting potential for flexible photoelectric applications due to its unique one-dimensional (1D) chain-type crystal structure, low-cost constituents, and superior optoelectronic properties. The 1D structure endows Sb2Se3 with a strong anisotropy in carrier transport and a lasting mechanical deformation tolerance. The control of the crystalline orientation of the Sb2Se3 film is an essential requirement for its device performance optimization. However, the current state-of-the-art Sb2Se3 devices suffer from unsatisfactory orientation control, especially for the (001) orientation, in which the chains stand vertically. Herein, we achieved an unprecedented control of the (001) orientation for the growth of the Sb2Se3 film on a flexible Mo-coated mica substrate by balancing the collision rate and kinetic energy of Se vapor particles with the surface of Sb film by regulating the selenization kinetics. Based on this (001)-oriented Sb2Se3 film, a high efficiency of 8.42% with a record open-circuit voltage (VOC) of 0.47 V is obtained for flexible Sb2Se3 solar cells. The vertical van der Waals gaps in the (001) orientation provide favorable diffusion paths for Se atoms, which results in a Se-rich state at the bottom of the Sb2Se3 film and promotes the in situ formation of the MoSe2 interlayer between Mo and Sb2Se3. These phenomena contribute to a back-surface field enhanced absorber layer and a quasi-Ohmic back contact, improving the device's VOC and the collection of carriers. This method provides an effective strategy for the orientation control of 1D materials for efficient photoelectric devices.
- 26 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (18) , 22251-22262
Vertically Aligned One-Dimensional Crystal-Structured Sb2Se3 for High-Efficiency Flexible Solar Cells via Regulating Selenization Kinetics
Recently, antimony selenide (Sb2Se3) has exhibited an exciting potential for flexible photoelectric applications due to its unique one-dimensional (1D) chain-type crystal structure, low-cost constituents, and superior optoelectronic properties. The 1D structure endows Sb2Se3 with a strong anisotropy in carrier transport and a lasting mechanical deformation tolerance. The control of the crystalline orientation of the Sb2Se3 film is an essential requirement for its device performance optimization. However, the current state-of-the-art Sb2Se3 devices suffer from unsatisfactory orientation control, especially for the (001) orientation, in which the chains stand vertically. Herein, we achieved an unprecedented control of the (001) orientation for the growth of the Sb2Se3 film on a flexible Mo-coated mica substrate by balancing the collision rate and kinetic energy of Se vapor particles with the surface of Sb film by regulating the selenization kinetics. Based on this (001)-oriented Sb2Se3 film, a high efficiency of 8.42% with a record open-circuit voltage (VOC) of 0.47 V is obtained for flexible Sb2Se3 solar cells. The vertical van der Waals gaps in the (001) orientation provide favorable diffusion paths for Se atoms, which results in a Se-rich state at the bottom of the Sb2Se3 film and promotes the in situ formation of the MoSe2 interlayer between Mo and Sb2Se3. These phenomena contribute to a back-surface field enhanced absorber layer and a quasi-Ohmic back contact, improving the device's VOC and the collection of carriers. This method provides an effective strategy for the orientation control of 1D materials for efficient photoelectric devices.
- 17 March 2023
- Published by Elsevier in Thin Solid Films
- Vol. 772
2D reciprocal space map of etched metalorganic chemical vapor deposited CdTe(001) film surface on miscut GaAs(001)
- 17 March 2023
- Published by Elsevier in Thin Solid Films
- Vol. 772
2D reciprocal space map of etched metalorganic chemical vapor deposited CdTe(001) film surface on miscut GaAs(001)
- 20 July 2022
- Published by Springer Nature in Nature
- Vol. 607 (7919) , 480-485
Giant pyroelectricity in nanomembranes
Pyroelectricity describes the generation of electricity by temporal temperature change in polar materials1,2,3. When free-standing pyroelectric materials approach the 2D crystalline limit, how pyroelectricity behaves remained largely unknown. Here, using three model pyroelectric materials whose bonding characters along the out-of-plane direction vary from van der Waals (In2Se3), quasi-van der Waals (CsBiNb2O7) to ionic/covalent (ZnO), we experimentally show the dimensionality effect on pyroelectricity and the relation between lattice dynamics and pyroelectricity. We find that, for all three materials, when the thickness of free-standing sheets becomes small, their pyroelectric coefficients increase rapidly. We show that the material with chemical bonds along the out-of-plane direction exhibits the greatest dimensionality effect. Experimental observations evidence the possible influence of changed phonon dynamics in crystals with reduced thickness on their pyroelectricity. Our findings should stimulate fundamental study on pyroelectricity in ultra-thin materials and inspire technological development for potential pyroelectric applications in thermal imaging and energy harvesting.
- 20 July 2022
- Published by Springer Nature in Nature
- Vol. 607 (7919) , 480-485
Giant pyroelectricity in nanomembranes
Pyroelectricity describes the generation of electricity by temporal temperature change in polar materials1,2,3. When free-standing pyroelectric materials approach the 2D crystalline limit, how pyroelectricity behaves remained largely unknown. Here, using three model pyroelectric materials whose bonding characters along the out-of-plane direction vary from van der Waals (In2Se3), quasi-van der Waals (CsBiNb2O7) to ionic/covalent (ZnO), we experimentally show the dimensionality effect on pyroelectricity and the relation between lattice dynamics and pyroelectricity. We find that, for all three materials, when the thickness of free-standing sheets becomes small, their pyroelectric coefficients increase rapidly. We show that the material with chemical bonds along the out-of-plane direction exhibits the greatest dimensionality effect. Experimental observations evidence the possible influence of changed phonon dynamics in crystals with reduced thickness on their pyroelectricity. Our findings should stimulate fundamental study on pyroelectricity in ultra-thin materials and inspire technological development for potential pyroelectric applications in thermal imaging and energy harvesting.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Free-Standing [001]-Oriented One-Dimensional Crystal-Structural Antimony Selenide Films for Self-Powered Flexible Near-Infrared Photodetectors
Flexible optoelectronic is one of the key components for acquiring biological signals in wearable devices and implantable systems. Recently, antimony selenide (Sb2Se3) has shown an exciting potential for flexible optoelectronic applications due to its unique one-dimensional (1D) ribbon-typed crystal structure, low-cost constituents, and superior optoelectronic properties. However, the growth of [001]-oriented Sb2Se3 film, which can efficiently enhance the carrier transport, is still challenging, particularly for its application in flexible electronics. Herein, we propose to grow the free-standing [001]-oriented Sb2Se3 film for self-powered flexible photodiode through selenizing the van der Waals (vdW) epitaxial Sb film on mica substrate. The epitaxial Sb film possesses a single (0001) out-of-plane orientation. The theoretical calculation reveals that Sb(0001) plane provides a high adsorption energy for Se atoms, which promotes the [001]-oriented growth of Sb2Se3 film. The weak vdW interaction between Sb2Se3 film and mica substrate enables the film separation, and results in a free-standing Sb2Se3 film. Benefiting from the enhanced carrier transport in [001]-oriented Sb2Se3 film, the flexible photodiode exhibits a high responsivity up to 0.74 A W-1, a specific detectivity of 5.1 × 1013 Jones, a linear dynamic range of 102 dB, rise/fall time of 0.16/0.15 ms for near-infrared light detection without any external bias, and excellent folding endurance after 1000 bending cycles. It has been also successfully employed as a wearable photodetector to detect a person’s heart rate. This work demonstrates a strategy for the orientation control of low-dimensional crystal-structural materials and a great potential of free-standing films in flexible electronics applications.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessFree-Standing [001]-Oriented One-Dimensional Crystal-Structural Antimony Selenide Films for Self-Powered Flexible Near-Infrared Photodetectors
Flexible optoelectronic is one of the key components for acquiring biological signals in wearable devices and implantable systems. Recently, antimony selenide (Sb2Se3) has shown an exciting potential for flexible optoelectronic applications due to its unique one-dimensional (1D) ribbon-typed crystal structure, low-cost constituents, and superior optoelectronic properties. However, the growth of [001]-oriented Sb2Se3 film, which can efficiently enhance the carrier transport, is still challenging, particularly for its application in flexible electronics. Herein, we propose to grow the free-standing [001]-oriented Sb2Se3 film for self-powered flexible photodiode through selenizing the van der Waals (vdW) epitaxial Sb film on mica substrate. The epitaxial Sb film possesses a single (0001) out-of-plane orientation. The theoretical calculation reveals that Sb(0001) plane provides a high adsorption energy for Se atoms, which promotes the [001]-oriented growth of Sb2Se3 film. The weak vdW interaction between Sb2Se3 film and mica substrate enables the film separation, and results in a free-standing Sb2Se3 film. Benefiting from the enhanced carrier transport in [001]-oriented Sb2Se3 film, the flexible photodiode exhibits a high responsivity up to 0.74 A W-1, a specific detectivity of 5.1 × 1013 Jones, a linear dynamic range of 102 dB, rise/fall time of 0.16/0.15 ms for near-infrared light detection without any external bias, and excellent folding endurance after 1000 bending cycles. It has been also successfully employed as a wearable photodetector to detect a person’s heart rate. This work demonstrates a strategy for the orientation control of low-dimensional crystal-structural materials and a great potential of free-standing films in flexible electronics applications.
- 10 August 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (6) , 065301
Domain boundaries in incommensurate epitaxial layers on weakly interacting substrates
There has been increasing interest in the fabrication of thin film materials with mixed dimensions, in particular, 2D to 3D and 3D to 2D heterostructures. Often, if the interface interaction is weak, the lattice matching criterion between the substrate and overlayer can be lifted. If the overlayer lattice is completely relaxed, it can form an incommensurate film on the mismatched substrate. In this work, we show that domain boundaries are inherent in the incommensurate epitaxial films due to random nucleation sites of domains in an overlayer. The nature and origin of the incommensurate domain boundaries are different from the conventional dislocation boundaries that come from the relaxation of strain due to film–substrate lattice mismatch. We propose that the formation of such domain boundaries can be studied through Voronoi tessellation. Using a case study of monolayer WS2 on sapphire (2D on 3D), we show the formation of domain boundaries that compared well with a recent experiment reported in the literature. In the Voronoi tessellation, we also show quantitatively that the average domain size depends on the density of nucleation sites. The conclusion of this case study may be generalized to any incommensurate epitaxial films when the interface interaction is weak.
- 10 August 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (6) , 065301
Domain boundaries in incommensurate epitaxial layers on weakly interacting substrates
There has been increasing interest in the fabrication of thin film materials with mixed dimensions, in particular, 2D to 3D and 3D to 2D heterostructures. Often, if the interface interaction is weak, the lattice matching criterion between the substrate and overlayer can be lifted. If the overlayer lattice is completely relaxed, it can form an incommensurate film on the mismatched substrate. In this work, we show that domain boundaries are inherent in the incommensurate epitaxial films due to random nucleation sites of domains in an overlayer. The nature and origin of the incommensurate domain boundaries are different from the conventional dislocation boundaries that come from the relaxation of strain due to film–substrate lattice mismatch. We propose that the formation of such domain boundaries can be studied through Voronoi tessellation. Using a case study of monolayer WS2 on sapphire (2D on 3D), we show the formation of domain boundaries that compared well with a recent experiment reported in the literature. In the Voronoi tessellation, we also show quantitatively that the average domain size depends on the density of nucleation sites. The conclusion of this case study may be generalized to any incommensurate epitaxial films when the interface interaction is weak.