Thomas Pinder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas Pinder has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Cindy Goppold
Laser Ablation and Cutting, Fraunhofer IWS, Fraunhofer-Institute for Material and Beam Technology, 01277 Dresden, Germany
2 shared publications - Andrés Fabián Lasagni
Institut für Fertigungstechnik Technische Universität Dresden Dresden Germany
1 shared publication - Patrick Herwig
Fraunhofer Institute for Material and Beam Technology IWS, Dresden, Germany
1 shared publication - Susanne Schulze
Fraunhofer IWS, Fraunhofer-Institute for Material and Beam Technology, 01277 Dresden, Germany
1 shared publication
Latest Publications
- Open Access
- 20 January 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (3) , 921
Understanding the Changed Mechanisms of Laser Beam Fusion Cutting by Applying Beam Oscillation, Based on Thermographic Analysis
The latest research on applying beam oscillation in laser beam fusion cutting revealed significant process improvements regarding speed and quality. The reason for this increasing process efficiency remains unexplained; however, theoretical investigations suggest the change in energy deposition (respectively heat conduction) as the cause. The present paper aims to analyze the energy deposition by a novel temperature measurement method. For this purpose, a conventional laser beam cutting setup was equipped with beam oscillation technology and a high-speed temperature measurement setup. Various characteristics of the temperature distribution in the process zone (spatial and temporal resolved temperature profiles, maximum and average values, as well as melt pool size) were evaluated for different conditions of beam oscillation (amplitude, frequency, cutting speed). Additionally, the geometrical properties of the process zone, defining the absorptivity have been measured. The comparison with static beam shaping reveals strong temperature volatility, which is induced by the way of energy deposition and an improved absorptivity over a substantial part of the cut front, with the overall result of enhanced heat conduction. For the first time, changed mechanisms applying beam oscillation instead of static beam shaping have been experimentally identified. Based on these measurements, a previously developed explanatory model was not only confirmed but also extended.
- 20 January 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (3) , 921
Open AccessUnderstanding the Changed Mechanisms of Laser Beam Fusion Cutting by Applying Beam Oscillation, Based on Thermographic Analysis
The latest research on applying beam oscillation in laser beam fusion cutting revealed significant process improvements regarding speed and quality. The reason for this increasing process efficiency remains unexplained; however, theoretical investigations suggest the change in energy deposition (respectively heat conduction) as the cause. The present paper aims to analyze the energy deposition by a novel temperature measurement method. For this purpose, a conventional laser beam cutting setup was equipped with beam oscillation technology and a high-speed temperature measurement setup. Various characteristics of the temperature distribution in the process zone (spatial and temporal resolved temperature profiles, maximum and average values, as well as melt pool size) were evaluated for different conditions of beam oscillation (amplitude, frequency, cutting speed). Additionally, the geometrical properties of the process zone, defining the absorptivity have been measured. The comparison with static beam shaping reveals strong temperature volatility, which is induced by the way of energy deposition and an improved absorptivity over a substantial part of the cut front, with the overall result of enhanced heat conduction. For the first time, changed mechanisms applying beam oscillation instead of static beam shaping have been experimentally identified. Based on these measurements, a previously developed explanatory model was not only confirmed but also extended.
- Open Access
- 27 April 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (9) , 3052
Improvement of Laser Beam Fusion Cutting of Mild and Stainless Steel Due to Longitudinal, Linear Beam Oscillation
The latest research on laser beam fusion cutting (LBFC) with static beam shaping have shown a limitation in the quality of cut parts for thick steel plates (> 6 mm) when using solid state lasers. The approach of dynamic beam oscillation has recently shown to be capable of overcoming this challenge, allowing to increase the cutting speed as well as improving cut edge quality beyond the state of the art. The present paper investigates the influence of longitudinal, linear beam oscillation in LBFC of 12 mm mild and stainless steel plates by analyzing different parameters as cutting speed, burr, surface roughness, heat affected zone (HAZ), and recast layer. Reasons for the observed process improvements compared to static beam shaping have been discussed. The adjustment of the energy deposition and interaction time of the laser beam with the material found to be most relevant for optimizing the LBFC process. In particular, for beam oscillation, a gradual energy deposition takes place and increases the interaction time. This reduces the heat input in terms of HAZ and recast layer by more than 50%, resulting in high cut edge quality and more than 70% faster cutting speed.
- 27 April 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (9) , 3052
Open AccessImprovement of Laser Beam Fusion Cutting of Mild and Stainless Steel Due to Longitudinal, Linear Beam Oscillation
The latest research on laser beam fusion cutting (LBFC) with static beam shaping have shown a limitation in the quality of cut parts for thick steel plates (> 6 mm) when using solid state lasers. The approach of dynamic beam oscillation has recently shown to be capable of overcoming this challenge, allowing to increase the cutting speed as well as improving cut edge quality beyond the state of the art. The present paper investigates the influence of longitudinal, linear beam oscillation in LBFC of 12 mm mild and stainless steel plates by analyzing different parameters as cutting speed, burr, surface roughness, heat affected zone (HAZ), and recast layer. Reasons for the observed process improvements compared to static beam shaping have been discussed. The adjustment of the energy deposition and interaction time of the laser beam with the material found to be most relevant for optimizing the LBFC process. In particular, for beam oscillation, a gradual energy deposition takes place and increases the interaction time. This reduces the heat input in terms of HAZ and recast layer by more than 50%, resulting in high cut edge quality and more than 70% faster cutting speed.