Balaji Morasa
Balaji Morasa has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Padmaja N
Sree Vidyanikethan Engineering College
3 shared publications- A. Yasmine Begum
Associate Professor, Department of ECE, Mohan Babu University, Tirupati, Andhra Pradesh, India
1 shared publication Charunya Devara
Sree Vidyanikethan Engineering College
1 shared publication- G. Chandraiah
Department of ECE, Sri Venkateswara College of Engineering, Tirupati, India
1 shared publication - G. Harshavardhan
Department of Electronics and Instrumentation Engineering, Sree Vidyanikethan Engineering College, Tirupati 517102, Andhra Pradesh, India
1 shared publication - G. Vishnuvardhan
Department of Electronics and Instrumentation Engineering, Sree Vidyanikethan Engineering College, Tirupati 517102, Andhra Pradesh, India
1 shared publication
Latest Publications
- Open Access
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (3) , 2116-2125
Electrocardiogram signal denoising and heart disease classification
Electrocardiogram (ECG) recordings are often contaminated by baseline wander (BLW), power-line interference, and motion or muscular noise, reducing the reliability of both manual and automated diagnosis. The paper presents a light and reproducible MATLAB pipeline applying finite-impulse-response (FIR) filters designed using Kaiser and Hamming windows for ECG denoising, which after R-peak detection follows an RR-interval analysis for classification of heart rate as tachycardia, bradycardia, or normal. In the experiments, 15 MIT-BIH records with added Gaussian noise at several SNR levels were used for benchmarking the performance of denoising. FIR band-pass and low-pass windowed filters improved the clarity of the waveform and supported robust R-peak detection; RR-interval-based classification reached a mean accuracy of ~98.7% on the study set. The approach is computationally lightweight and quite suitable for embedded real-time deployment but is restricted to the small sample of records and synthetic noise modeling. Future work will compare the efficacy of windowed FIR filtering against modern deep-learning denoisers (CNN/RNN/GAN architectures) and assess the pipeline in larger clinical datasets.
- 1 June 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (3) , 2116-2125
Open AccessElectrocardiogram signal denoising and heart disease classification
Electrocardiogram (ECG) recordings are often contaminated by baseline wander (BLW), power-line interference, and motion or muscular noise, reducing the reliability of both manual and automated diagnosis. The paper presents a light and reproducible MATLAB pipeline applying finite-impulse-response (FIR) filters designed using Kaiser and Hamming windows for ECG denoising, which after R-peak detection follows an RR-interval analysis for classification of heart rate as tachycardia, bradycardia, or normal. In the experiments, 15 MIT-BIH records with added Gaussian noise at several SNR levels were used for benchmarking the performance of denoising. FIR band-pass and low-pass windowed filters improved the clarity of the waveform and supported robust R-peak detection; RR-interval-based classification reached a mean accuracy of ~98.7% on the study set. The approach is computationally lightweight and quite suitable for embedded real-time deployment but is restricted to the small sample of records and synthetic noise modeling. Future work will compare the efficacy of windowed FIR filtering against modern deep-learning denoisers (CNN/RNN/GAN architectures) and assess the pipeline in larger clinical datasets.
- 24 February 2026
- Published by Springer Nature in Wireless Personal Communications
- Vol. 146 (3) , 1629-1666
Super-Wide Band (25–43 GHz), 4-Element MIMO Antenna with High Diversity for 5G Mm Wave Advanced Wireless System Applications
- 24 February 2026
- Published by Springer Nature in Wireless Personal Communications
- Vol. 146 (3) , 1629-1666
Super-Wide Band (25–43 GHz), 4-Element MIMO Antenna with High Diversity for 5G Mm Wave Advanced Wireless System Applications
- Open Access
- 31 January 2024
- Published by Wiley
LOW POWER RNS SYSTEM USING LUT DECOMPOSITION AND FSM BASED POST COMPUTATION FOR EEG SIGNAL CLASSIFICATION
In this paper, memory optimization and architectural level modifications are introduced for low power realization of the Residue Number System(RNS) with improved flexibility for EEG signal classification. The proposed RNS framework is intended to maximize the reconfigurability of RNS for high-performance FIR filter design. By replacing the existing power-hungry RAM-based reverse conversion model with a highly decomposed LUT model which can produce the results without using any post accumulation process. The proposed RNS design makes use of inherent parallelism among residue channels and resources available of FPGA devices, the reverse conversion block is modified with an appropriate functional unit to accommodate FIR convolution results. The proposed approach is formulated to design pre-computed reverse converters for different moduli sets and implemented based on FPGA as target devices. As a result, the proposed LUT-based direct computation-based post accumulation technique for RNS-based multiplication offers high-performance FIR filter architecture which can also allow configuring the elements for different frequency responses. Experimental results show the superior performance of decomposing LUT-based direct reverse conversion over all other existing reverse conversion techniques adopted for energy-efficient RNS FIR implementations.
- 31 January 2024
- Published by Wiley
Open AccessLOW POWER RNS SYSTEM USING LUT DECOMPOSITION AND FSM BASED POST COMPUTATION FOR EEG SIGNAL CLASSIFICATION
In this paper, memory optimization and architectural level modifications are introduced for low power realization of the Residue Number System(RNS) with improved flexibility for EEG signal classification. The proposed RNS framework is intended to maximize the reconfigurability of RNS for high-performance FIR filter design. By replacing the existing power-hungry RAM-based reverse conversion model with a highly decomposed LUT model which can produce the results without using any post accumulation process. The proposed RNS design makes use of inherent parallelism among residue channels and resources available of FPGA devices, the reverse conversion block is modified with an appropriate functional unit to accommodate FIR convolution results. The proposed approach is formulated to design pre-computed reverse converters for different moduli sets and implemented based on FPGA as target devices. As a result, the proposed LUT-based direct computation-based post accumulation technique for RNS-based multiplication offers high-performance FIR filter architecture which can also allow configuring the elements for different frequency responses. Experimental results show the superior performance of decomposing LUT-based direct reverse conversion over all other existing reverse conversion techniques adopted for energy-efficient RNS FIR implementations.
- Open Access
- 31 October 2023
- Published by Seventh Sense Research Group Journals in International Journal of Electrical and Electronics Engineering
- Vol. 10 (10) , 151-164
Area and Delay Efficient RNS-Based FIR Filter Design Using Fast Adders and Multipliers
Speed and area are the primary design concerns in today’s digital age. Increasing the rate at which multiplications and additions are performed has always been necessary for developing cutting-edge technologies. Wallace and Dadda multipliers are among the fastest multipliers used in many processors to accomplish fast arithmetic operations. A novel approach to design a Lookup Table (LUT) multiplier and adder was proposed and implemented in the Finite Impulse Response (FIR) filter. To improve the Residue Number System (RNS) based FIR filter’s performance, several adders like Carry Look Ahead (CLA) adder, Kogge Stone Adder (KSA) and proposed adder architectures have also been implemented. Compared with the 16 taps with 32-bit proposed adder with LUT multiplier, the hardware resource utilization (Logic Elements) is decreased by 5.97% and in 32 taps with 16-bit combination, it reduces by 7.60%. Compared with 32 taps with 4- bit word length, the proposed adder with LUT multiplier in the highlighted combinations, the Fmax is increased by 19.28% and in 32 taps with 16-bit, it increases by 29.74%. The Low-pass RNS FIR filter is designed for a cutoff frequency of 50 Hz, generated filter coefficients in MATLAB, and implemented to denoise the ECG signal.
- 31 October 2023
- Published by Seventh Sense Research Group Journals in International Journal of Electrical and Electronics Engineering
- Vol. 10 (10) , 151-164
Open AccessArea and Delay Efficient RNS-Based FIR Filter Design Using Fast Adders and Multipliers
Speed and area are the primary design concerns in today’s digital age. Increasing the rate at which multiplications and additions are performed has always been necessary for developing cutting-edge technologies. Wallace and Dadda multipliers are among the fastest multipliers used in many processors to accomplish fast arithmetic operations. A novel approach to design a Lookup Table (LUT) multiplier and adder was proposed and implemented in the Finite Impulse Response (FIR) filter. To improve the Residue Number System (RNS) based FIR filter’s performance, several adders like Carry Look Ahead (CLA) adder, Kogge Stone Adder (KSA) and proposed adder architectures have also been implemented. Compared with the 16 taps with 32-bit proposed adder with LUT multiplier, the hardware resource utilization (Logic Elements) is decreased by 5.97% and in 32 taps with 16-bit combination, it reduces by 7.60%. Compared with 32 taps with 4- bit word length, the proposed adder with LUT multiplier in the highlighted combinations, the Fmax is increased by 19.28% and in 32 taps with 16-bit, it increases by 29.74%. The Low-pass RNS FIR filter is designed for a cutoff frequency of 50 Hz, generated filter coefficients in MATLAB, and implemented to denoise the ECG signal.
- Open Access
- 13 October 2022
- Published by Springer Nature in Research Square
Distributed Arithmetic RNS-based FIR Filter Design using Pipelining and Retiming Methods for High-Speed DSP Systems
This work presents a way to increase the throughput and energy efficiency of finite impulse response (FIR) filters through the efficient application of retiming and two-level pipelining. It is a challenge to increase the filter's throughput and energy efficiency while reducing latency and hardware complexity. The operations of addition and multiplication are divided using two-level pipelining. The break addition procedure is retimed. The architecture of m-tap filter (4-tap, 8-tap, 16-tap, 32-tap, and 64-tap) with n-bit input word length (4-bit, 8-bit, 16-bit, and 32-bit) Pipelined Retiming delay generation Filters (PRF), were designed. The proposed distributed arithmetic-based FIR Filter with pipelining has produced the least delay of 2.564ns for 4-tap with 8-bit input, and the maximum delay of 56.040ns for 64-tap with 32-bit word length. The proposed distributed arithmetic-based FIR Filter with retiming method has produced the least delay of 0.687ns for 4-tap with 8-bit input, and the maximum delay of 4.535ns for 64-tap with 32-bit word length. When compared with the pipelining method, the delay has been decreased by 73.20% for 4-tap with 8-bit input and 91.90% for 64-tap with 32-bit word length.
- 13 October 2022
- Published by Springer Nature in Research Square
Open AccessDistributed Arithmetic RNS-based FIR Filter Design using Pipelining and Retiming Methods for High-Speed DSP Systems
This work presents a way to increase the throughput and energy efficiency of finite impulse response (FIR) filters through the efficient application of retiming and two-level pipelining. It is a challenge to increase the filter's throughput and energy efficiency while reducing latency and hardware complexity. The operations of addition and multiplication are divided using two-level pipelining. The break addition procedure is retimed. The architecture of m-tap filter (4-tap, 8-tap, 16-tap, 32-tap, and 64-tap) with n-bit input word length (4-bit, 8-bit, 16-bit, and 32-bit) Pipelined Retiming delay generation Filters (PRF), were designed. The proposed distributed arithmetic-based FIR Filter with pipelining has produced the least delay of 2.564ns for 4-tap with 8-bit input, and the maximum delay of 56.040ns for 64-tap with 32-bit word length. The proposed distributed arithmetic-based FIR Filter with retiming method has produced the least delay of 0.687ns for 4-tap with 8-bit input, and the maximum delay of 4.535ns for 64-tap with 32-bit word length. When compared with the pipelining method, the delay has been decreased by 73.20% for 4-tap with 8-bit input and 91.90% for 64-tap with 32-bit word length.
- 1 January 2022
- Published by Springer Nature
- p. 461-470
Smart Monitoring System for Waste Management Using IoT
- 1 January 2022
- Published by Springer Nature
- p. 461-470
Smart Monitoring System for Waste Management Using IoT
- 17 February 2020
- Published by Taru Publications in Journal of Information and Optimization Sciences
- Vol. 41 (2) , 489-497
Development of animal collar for state of health determination of livestock
The variation of Livestock physiological parameters such as stress level, rumination, body temperature has harmful effect in reproduction cycle and also causes diseases such as Mastitis, Milk fever, Lameness etc. Development of animal collar for monitoring the physiological parameters may help in better management of cattle diseases and reproduction cycle. The advantages of this system include simplicity, portability and inexpensive health care of livestock. The cattle surface body temperature was measured continuously for one day with an interval of one hour. The body temperature of the cattle measured using DHT11 sensor and mercury thermometer is compared and the average difference between the temperature measured using DHT11 sensor and mercury thermometer is 0.03°C indicating the feasibility of this method to monitor state of health of a cattle. With the temperature data and humidity data obtained from DHT11 sensor THI index is calculated and stress level of the cattle is predicted without using any sensor. The ADXL335 sensor is fixed under the collar near the left side of the mouth of the livestock to monitor rumination of cattle. This system is implemented in the Rangampet village, Chittoor district in Andhra Pradesh. The prototype of the collar based cattle health monitoring system shows that it is helpful for livestock farmers for recognizing various diseases accurately.
- 17 February 2020
- Published by Taru Publications in Journal of Information and Optimization Sciences
- Vol. 41 (2) , 489-497
Development of animal collar for state of health determination of livestock
The variation of Livestock physiological parameters such as stress level, rumination, body temperature has harmful effect in reproduction cycle and also causes diseases such as Mastitis, Milk fever, Lameness etc. Development of animal collar for monitoring the physiological parameters may help in better management of cattle diseases and reproduction cycle. The advantages of this system include simplicity, portability and inexpensive health care of livestock. The cattle surface body temperature was measured continuously for one day with an interval of one hour. The body temperature of the cattle measured using DHT11 sensor and mercury thermometer is compared and the average difference between the temperature measured using DHT11 sensor and mercury thermometer is 0.03°C indicating the feasibility of this method to monitor state of health of a cattle. With the temperature data and humidity data obtained from DHT11 sensor THI index is calculated and stress level of the cattle is predicted without using any sensor. The ADXL335 sensor is fixed under the collar near the left side of the mouth of the livestock to monitor rumination of cattle. This system is implemented in the Rangampet village, Chittoor district in Andhra Pradesh. The prototype of the collar based cattle health monitoring system shows that it is helpful for livestock farmers for recognizing various diseases accurately.