Tezhuan Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tezhuan Du has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Yiwei Wang
Chinese Academy of Sciences
7 shared publications - Jingzhu Wang
Chinese Academy of Sciences
6 shared publications - Yongjiu Wang
Key Laboratory for Mechanics in Fluid-Solid Coupling Systems, Institute of Mechanics, Chinese Academy of Sciences 2 , Beijing 100190
3 shared publications - Bin Zhang
Key Laboratory for Mechanics in Fluid Solid Coupling Systems, Institute of Mechanics, Chinese Academy of Sciences 1 , Beijing 100190
2 shared publications Cheng-Guang Huang
Key Laboratory for Mechanics in Fluid Solid Coupling Systems, Institute of Mechanics, Chinese Academy of Sciences, Beijing, China
2 shared publications- Jian Huang
Key Laboratory for Mechanics in Fluid Solid Coupling Systems, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, People’s Republic of China
2 shared publications
Latest Publications
- 1 July 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (7)
Cavitation dynamics of a yawed T-foil: Multistage shedding and asymmetric evolution
The cavitation dynamics of a yawed T-shaped hydrofoil (T-foil) comprising a surface-piercing strut and a submerged hydrofoil significantly undermine the high-speed maneuverability of the hydrofoil craft. In this study, the unsteady cavitating flows over a T-foil at various yaw angles (β) are systematically investigated by coupling constrained launching experiments and large eddy simulations. It is found that, at β = 0°, a symmetric cavity multistage shedding observed from the T-foil is elucidated. As β ≥ 5°, the cross-flow effect drives a symmetry-breaking cavity evolution. Cavitation on the windward side progressively regresses to sheet cavitation and is ultimately suppressed, while violent unsteady cloud cavitation persists on the leeward side. Consequently, the excitation mechanism for lateral force fluctuations sequentially transitions from bilateral symmetric to unilateral dominant, and ultimately to strut–hydrofoil coupled. Furthermore, a flow regime map of the yawed T-foil is established, revealing asymmetric divergence of the cavitation inception boundaries between the leeward and windward submerged hydrofoils, primarily driven by the strut-induced vortex velocity modulation effect. The drag coefficient continuously increases with decreasing cavitation number, whereas the lateral force coefficient and lift coefficient first increase slightly and then decrease significantly in cavitating flow, and undergo abrupt transitions under the fully ventilated regime. These findings provide preliminary insights into the hydrodynamic design and stability control of similar T-foil configurations.
- 1 July 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (7)
Cavitation dynamics of a yawed T-foil: Multistage shedding and asymmetric evolution
The cavitation dynamics of a yawed T-shaped hydrofoil (T-foil) comprising a surface-piercing strut and a submerged hydrofoil significantly undermine the high-speed maneuverability of the hydrofoil craft. In this study, the unsteady cavitating flows over a T-foil at various yaw angles (β) are systematically investigated by coupling constrained launching experiments and large eddy simulations. It is found that, at β = 0°, a symmetric cavity multistage shedding observed from the T-foil is elucidated. As β ≥ 5°, the cross-flow effect drives a symmetry-breaking cavity evolution. Cavitation on the windward side progressively regresses to sheet cavitation and is ultimately suppressed, while violent unsteady cloud cavitation persists on the leeward side. Consequently, the excitation mechanism for lateral force fluctuations sequentially transitions from bilateral symmetric to unilateral dominant, and ultimately to strut–hydrofoil coupled. Furthermore, a flow regime map of the yawed T-foil is established, revealing asymmetric divergence of the cavitation inception boundaries between the leeward and windward submerged hydrofoils, primarily driven by the strut-induced vortex velocity modulation effect. The drag coefficient continuously increases with decreasing cavitation number, whereas the lateral force coefficient and lift coefficient first increase slightly and then decrease significantly in cavitating flow, and undergo abrupt transitions under the fully ventilated regime. These findings provide preliminary insights into the hydrodynamic design and stability control of similar T-foil configurations.
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Investigation of the air film around an axisymmetric projectile with a pressure-equalizing exhaust system
This study numerically investigates air film flow around a projectile with a pressure-equalizing exhaust system. Dimensional analysis is employed to identify the key dimensionless parameters governing flow regime transitions. The air film evolution is categorized into three distinct stages: rapid growth, periodic pulsation, and quasi-steady. The characteristics of the air film and the associated development of the flow field are analyzed. Analysis reveals that the reentrant jet strength and gas injection rate are the primary factors driving transitions in the flow pattern. The velocity vector field reveals that the upstream-propagating reentrant jet dominates interfacial instability and periodic air film shedding, governing the flow regime transition of the air film. During the rapid growth stage, the pressure gradient exhibits minor fluctuations. However, it intensifies markedly upon transition into the periodic pulsation stage. Wavelet analysis reveals that frictional drag is linked to air film geometry, while tail cavity pulsations dominate pressure drag. Pressure drag constitutes ∼95% of the total drag, driven by high-pressure pulsation from the tail cavity, which is affected by the shedding of air film convected downstream. This study provides valuable insights for the engineering design and active flow control of projectiles.
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Investigation of the air film around an axisymmetric projectile with a pressure-equalizing exhaust system
This study numerically investigates air film flow around a projectile with a pressure-equalizing exhaust system. Dimensional analysis is employed to identify the key dimensionless parameters governing flow regime transitions. The air film evolution is categorized into three distinct stages: rapid growth, periodic pulsation, and quasi-steady. The characteristics of the air film and the associated development of the flow field are analyzed. Analysis reveals that the reentrant jet strength and gas injection rate are the primary factors driving transitions in the flow pattern. The velocity vector field reveals that the upstream-propagating reentrant jet dominates interfacial instability and periodic air film shedding, governing the flow regime transition of the air film. During the rapid growth stage, the pressure gradient exhibits minor fluctuations. However, it intensifies markedly upon transition into the periodic pulsation stage. Wavelet analysis reveals that frictional drag is linked to air film geometry, while tail cavity pulsations dominate pressure drag. Pressure drag constitutes ∼95% of the total drag, driven by high-pressure pulsation from the tail cavity, which is affected by the shedding of air film convected downstream. This study provides valuable insights for the engineering design and active flow control of projectiles.
- 20 March 2026
- Published by Elsevier in Ocean Engineering
- Vol. 355
Effect of yaw angle on natural ventilated flow around a T-foil
- 20 March 2026
- Published by Elsevier in Ocean Engineering
- Vol. 355
Effect of yaw angle on natural ventilated flow around a T-foil
- 1 March 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (3)
Transient impact force of water drops impinging on cylindrical superhydrophobic surfaces
Drop impact on cylindrical substrates is more common than on flat substrates in many natural and engineering settings. Quantifying the transient impact force in drop-cylinder collisions is, therefore, crucial for understanding drop dynamics on curved substrates and for applications, such as icing mitigation, heat-transfer enhancement, and erosion reduction. Here, we experimentally investigate the transient impact force and morphological evolution of water drops impacting superhydrophobic cylinders, using a piezoelectric force sensor synchronized with high-speed imaging. The cylinder diameter ranges from 2 mm, which is comparable to the drop diameter of 2.05 mm, up to the flat-surface limit, while the Weber number varies from 4.5 to 102.2. Our results show that, on both flat and cylindrical superhydrophobic substrates, the impact force exhibits two distinct peaks. For the first peak, we find that at low Weber numbers the dynamics are governed by the combined effects of inertia and surface tension, while the influence of curvature remains weak. As the Weber number increases, the dependence of the first peak on curvature becomes increasingly pronounced. Based on the scaling analysis, we establish a quantitative relationship between the normalized first peak and the ratio of cylinder diameter to drop diameter. In contrast, the second peak is highly sensitive to curvature at low Weber numbers. The singular Worthington jet that forms on flat surfaces and cylinders with large diameter is suppressed on cylinders with small diameter due to the strongly asymmetric interfacial evolution. Consequently, the second peak decreases significantly as the cylinder diameter is reduced.
- 1 March 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (3)
Transient impact force of water drops impinging on cylindrical superhydrophobic surfaces
Drop impact on cylindrical substrates is more common than on flat substrates in many natural and engineering settings. Quantifying the transient impact force in drop-cylinder collisions is, therefore, crucial for understanding drop dynamics on curved substrates and for applications, such as icing mitigation, heat-transfer enhancement, and erosion reduction. Here, we experimentally investigate the transient impact force and morphological evolution of water drops impacting superhydrophobic cylinders, using a piezoelectric force sensor synchronized with high-speed imaging. The cylinder diameter ranges from 2 mm, which is comparable to the drop diameter of 2.05 mm, up to the flat-surface limit, while the Weber number varies from 4.5 to 102.2. Our results show that, on both flat and cylindrical superhydrophobic substrates, the impact force exhibits two distinct peaks. For the first peak, we find that at low Weber numbers the dynamics are governed by the combined effects of inertia and surface tension, while the influence of curvature remains weak. As the Weber number increases, the dependence of the first peak on curvature becomes increasingly pronounced. Based on the scaling analysis, we establish a quantitative relationship between the normalized first peak and the ratio of cylinder diameter to drop diameter. In contrast, the second peak is highly sensitive to curvature at low Weber numbers. The singular Worthington jet that forms on flat surfaces and cylinders with large diameter is suppressed on cylinders with small diameter due to the strongly asymmetric interfacial evolution. Consequently, the second peak decreases significantly as the cylinder diameter is reduced.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Hydrodynamic performance of a surface-piercing hydrofoil with differing oblique angle: A numerical study
Oblique surface-piercing hydrofoils are used widely to impart lift to high-speed surface vehicles, and their lift and drag, and hence working efficiency, are affected by their oblique angle and velocity. Reported here is a numerical study of the ventilation and hydrodynamic performance of a surface-piercing hydrofoil with an oblique angle, using the two-phase interFoam solver in OpenFOAM to simulate the hydrofoil processes. The results show that two main regimes occur when the surface-piercing hydrofoil moves in a stable manner, i.e., fully wetted and fully ventilated (the latter comprising tip-vortex-induced ventilation and perturbation-induced ventilation), which are affected by the oblique angle. At low velocity, increasing the oblique angle does not change the ventilation regime but does improve the lift-to-drag ratio of the hydrofoil. At high velocity, as the oblique angle increases, the hydrofoil changes from tip-vortex-induced ventilation to fully wetted, and the lift-to-drag ratio is also increased. In particular, when the oblique angle reaches 30°, perturbation-induced ventilation occurs and the hydrofoil stalls. A phase diagram of the ventilation regime at different values of the Froude number and oblique angle is presented. Given that surface-piercing hydrofoils impart lift to high-speed surface vehicles, an oblique angle of 25° is recommended as being suitable for hydrofoils within the parameters discussed in the paper. These findings support the engineering applications of surface-piercing hydrofoils.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Hydrodynamic performance of a surface-piercing hydrofoil with differing oblique angle: A numerical study
Oblique surface-piercing hydrofoils are used widely to impart lift to high-speed surface vehicles, and their lift and drag, and hence working efficiency, are affected by their oblique angle and velocity. Reported here is a numerical study of the ventilation and hydrodynamic performance of a surface-piercing hydrofoil with an oblique angle, using the two-phase interFoam solver in OpenFOAM to simulate the hydrofoil processes. The results show that two main regimes occur when the surface-piercing hydrofoil moves in a stable manner, i.e., fully wetted and fully ventilated (the latter comprising tip-vortex-induced ventilation and perturbation-induced ventilation), which are affected by the oblique angle. At low velocity, increasing the oblique angle does not change the ventilation regime but does improve the lift-to-drag ratio of the hydrofoil. At high velocity, as the oblique angle increases, the hydrofoil changes from tip-vortex-induced ventilation to fully wetted, and the lift-to-drag ratio is also increased. In particular, when the oblique angle reaches 30°, perturbation-induced ventilation occurs and the hydrofoil stalls. A phase diagram of the ventilation regime at different values of the Froude number and oblique angle is presented. Given that surface-piercing hydrofoils impart lift to high-speed surface vehicles, an oblique angle of 25° is recommended as being suitable for hydrofoils within the parameters discussed in the paper. These findings support the engineering applications of surface-piercing hydrofoils.
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Experimental and numerical study on ventilated cavitation of high-speed projectile
In this study, ventilated cavitating flow characteristics around an axisymmetric projectile are investigated by combining experiments and numerical simulations. Experiments were carried out with a Split–Hopkinson pressure bar launch system and the pressure-equaling exhaust technology. Modular projectiles are designed to experimentally investigate the influence of head shape and ventilatory volume on flow characteristics. Large eddy simulation model is applied to obtain more flow field information. Compared with the conical head projectile, the hemispherical head projectile has a thinner attached cavity and more local detachment of the cavity. The statistical structure of the velocity and pressure fluctuations are analyzed by combining histograms and Q–Q diagrams. The results show that the pressure drag is dominant in the total drag and the periodic pulsation of the tail cavity and the stable vortex structure at the tail cause the variation of drag. The larger cavity volume changes the actual shape of the projectile, making the drag of the conical head projectile higher. The evolution characteristics of the cavitating flow field around the projectile with different ventilatory volumes are obtained, and the relationship between pressure fluctuation and chamber volume is derived. It is found that the reentrant jet causes a reverse flow at the nozzle, which leads to local pressure rise at the same interval. The above research work could contribute to the design and flow control of the ventilated cavity body.
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Experimental and numerical study on ventilated cavitation of high-speed projectile
In this study, ventilated cavitating flow characteristics around an axisymmetric projectile are investigated by combining experiments and numerical simulations. Experiments were carried out with a Split–Hopkinson pressure bar launch system and the pressure-equaling exhaust technology. Modular projectiles are designed to experimentally investigate the influence of head shape and ventilatory volume on flow characteristics. Large eddy simulation model is applied to obtain more flow field information. Compared with the conical head projectile, the hemispherical head projectile has a thinner attached cavity and more local detachment of the cavity. The statistical structure of the velocity and pressure fluctuations are analyzed by combining histograms and Q–Q diagrams. The results show that the pressure drag is dominant in the total drag and the periodic pulsation of the tail cavity and the stable vortex structure at the tail cause the variation of drag. The larger cavity volume changes the actual shape of the projectile, making the drag of the conical head projectile higher. The evolution characteristics of the cavitating flow field around the projectile with different ventilatory volumes are obtained, and the relationship between pressure fluctuation and chamber volume is derived. It is found that the reentrant jet causes a reverse flow at the nozzle, which leads to local pressure rise at the same interval. The above research work could contribute to the design and flow control of the ventilated cavity body.
- Open Access
- 1 July 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (7)
Study on the energy-focusing mechanism of spatial bubble clusters
Cavitation research has important implications in fields such as mechanical drag reduction, material processing, and new medical device development. Bubble cluster formation, development, and collapse are critical steps in the cavitation process. High-precision numerical simulations have shown that the collapse of bubble clusters exhibits a characteristic energy focusing from the outside to the inside. This study proposes a focus-type model for the energy transfer in bubble clusters to analyze the formation mechanism of collapse pressure and improve the accuracy of quantitative predictions. The model comprises multiple bubbles (α) radiating energy and a bubble (β) receiving energy. Through numerical simulation, the energy transfer law during bubble interaction is studied, showing that relative energy transfer decreases as the dimensionless distance increases, which corresponds with the theoretical model. The study further analyses the relationship between energy transfer in basic and composite bubble cluster structures. Additionally, the study observed the pressure focusing effect of the bubble clusters and found a strong correlation between the focusing effect and dimensionless distance.
- 1 July 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (7)
Open AccessStudy on the energy-focusing mechanism of spatial bubble clusters
Cavitation research has important implications in fields such as mechanical drag reduction, material processing, and new medical device development. Bubble cluster formation, development, and collapse are critical steps in the cavitation process. High-precision numerical simulations have shown that the collapse of bubble clusters exhibits a characteristic energy focusing from the outside to the inside. This study proposes a focus-type model for the energy transfer in bubble clusters to analyze the formation mechanism of collapse pressure and improve the accuracy of quantitative predictions. The model comprises multiple bubbles (α) radiating energy and a bubble (β) receiving energy. Through numerical simulation, the energy transfer law during bubble interaction is studied, showing that relative energy transfer decreases as the dimensionless distance increases, which corresponds with the theoretical model. The study further analyses the relationship between energy transfer in basic and composite bubble cluster structures. Additionally, the study observed the pressure focusing effect of the bubble clusters and found a strong correlation between the focusing effect and dimensionless distance.
- 12 July 2022
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 38 (11) , 1-10
Studies on two-bubble energy transfer model with radiant-receiver structure
- 12 July 2022
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 38 (11) , 1-10
Studies on two-bubble energy transfer model with radiant-receiver structure
- Open Access
- 1 February 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (2) , 023316
Research on ventilation and supercavitation mechanism of high-speed surface-piercing hydrofoil
Flow structures and hydrodynamic performance of high-speed surface-piercing hydrofoils were studied by numerical simulation, with an emphasis on the interaction mechanism between supercavitation and natural ventilation. Compared with the available experimental data, the numerical method could predict the cavitation and ventilation well. The numerical simulation results show that the flow over hydrofoil with blunt trailing edge is more conducive to separating. The semi-ogive hydrofoil was used to explore the influence of angles of attack on ventilation and cavitation. The ventilation rate increases with the increase in the angles of attack. At small attack angles (α = 0° and 2°), the regional ventilated flow is found in supercavitation. The vortex street structures and twin vortices closure mode are formed in the closure region of the supercavity. At moderate attack angles (α = 6° and 10°), the thickness of the undisturbed liquid sheet (δ) becomes thinner and the natural supercavitation transits to fully ventilated supercavitation through the cavitation-induced ventilation, but the ventilation position is different because of Taylor instability. The hydrodynamic coefficients remain relatively stable in natural supercavitation and the lift coefficient reduce to half of the original value when the supercavitation is fully ventilated, which are caused by the pressure changes on the suction and pressure surfaces.
- 1 February 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (2) , 023316
Open AccessResearch on ventilation and supercavitation mechanism of high-speed surface-piercing hydrofoil
Flow structures and hydrodynamic performance of high-speed surface-piercing hydrofoils were studied by numerical simulation, with an emphasis on the interaction mechanism between supercavitation and natural ventilation. Compared with the available experimental data, the numerical method could predict the cavitation and ventilation well. The numerical simulation results show that the flow over hydrofoil with blunt trailing edge is more conducive to separating. The semi-ogive hydrofoil was used to explore the influence of angles of attack on ventilation and cavitation. The ventilation rate increases with the increase in the angles of attack. At small attack angles (α = 0° and 2°), the regional ventilated flow is found in supercavitation. The vortex street structures and twin vortices closure mode are formed in the closure region of the supercavity. At moderate attack angles (α = 6° and 10°), the thickness of the undisturbed liquid sheet (δ) becomes thinner and the natural supercavitation transits to fully ventilated supercavitation through the cavitation-induced ventilation, but the ventilation position is different because of Taylor instability. The hydrodynamic coefficients remain relatively stable in natural supercavitation and the lift coefficient reduce to half of the original value when the supercavitation is fully ventilated, which are caused by the pressure changes on the suction and pressure surfaces.
- 29 October 2020
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 32 (5) , 865-878
Numerical investigations of the transient cavitating vortical flow structures over a flexible NACA66 hydrofoil
- 29 October 2020
- Published by Springer Nature in Journal of Hydrodynamics
- Vol. 32 (5) , 865-878
Numerical investigations of the transient cavitating vortical flow structures over a flexible NACA66 hydrofoil