Nataliya Bekhta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nataliya Bekhta has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Pavlo Bekhta
Mendel University in Brno
5 shared publications - Barbara Lis
Department of Wood Science and Thermal Techniques, Faculty of Forestry and Wood Technology, Poznań University of Life Sciences, Poznań, Poland
3 shared publications - Tomasz Krystofiak
Department of Wood Science and Thermal Techniques, Faculty of Forestry and Wood Technology, Poznań University of Life Sciences, Poznań, Poland
3 shared publications - Antonio Pizzi
LERMAB-ENSTIB, University of Lorraine, 27 rue Philippe Seguin, 88000 Epinal, France
1 shared publication - Arif Nuryawan
Faculty of Forestry, Universitas Sumatera Utara
1 shared publication - Iryna Kusniak
Національний лісотехнічний університет України
1 shared publication
Latest Publications
- Open Access
A Comparative Study of Several Properties of Plywood Bonded with Virgin and Recycled LDPE Films
In this work, to better understand the bonding process of plastic plywood panels, the effects of recycled low-density polyethylene (rLDPE) film of three thicknesses (50, 100, and 150 µm) and veneers of four various wood species (beech, birch, hornbeam, and poplar) on the properties of panels were studied. The obtained properties were also compared with the properties of plywood panels bonded by virgin low-density polyethylene (LDPE) film. The results showed that properties of plywood samples bonded with rLDPE and virgin LDPE films differ insignificantly. Samples bonded with rLDPE film demonstrated satisfactory physical and mechanical properties. It was also established that the best mechanical properties of plywood are provided by beech veneer and the lowest by poplar veneer. However, poplar plywood had the best water absorption and swelling thickness, and the bonding strength at the level of birch and hornbeam plywood. The properties of rLDPE-bonded plywood improved with increasing the thickness of the film. The panels bonded with rLDPE film had a close-to-zero formaldehyde content (0.01–0.10 mg/m2·h) and reached the super E0 emission class that allows for defining the laboratory-manufactured plastic-bonded plywood as an eco-friendly composite.
Open AccessA Comparative Study of Several Properties of Plywood Bonded with Virgin and Recycled LDPE Films
In this work, to better understand the bonding process of plastic plywood panels, the effects of recycled low-density polyethylene (rLDPE) film of three thicknesses (50, 100, and 150 µm) and veneers of four various wood species (beech, birch, hornbeam, and poplar) on the properties of panels were studied. The obtained properties were also compared with the properties of plywood panels bonded by virgin low-density polyethylene (LDPE) film. The results showed that properties of plywood samples bonded with rLDPE and virgin LDPE films differ insignificantly. Samples bonded with rLDPE film demonstrated satisfactory physical and mechanical properties. It was also established that the best mechanical properties of plywood are provided by beech veneer and the lowest by poplar veneer. However, poplar plywood had the best water absorption and swelling thickness, and the bonding strength at the level of birch and hornbeam plywood. The properties of rLDPE-bonded plywood improved with increasing the thickness of the film. The panels bonded with rLDPE film had a close-to-zero formaldehyde content (0.01–0.10 mg/m2·h) and reached the super E0 emission class that allows for defining the laboratory-manufactured plastic-bonded plywood as an eco-friendly composite.
- Open Access
Gloss of Varnished MDF Panels Veneered with Sanded and Thermally Compressed Veneer
The objective of this study was to investigate the gloss of different types of commercially manufactured varnish systems, including water-based (WB), polyurethane (PUR) and UV-cured (UV), applied on veneered MDF panels with sanded and thermally densified alder and birch wood veneers. The varnishes were applied at various numbers of layers on veneered panels. The gloss was measured at three angles of incident light: 20°, 60° and 85°. Statistical analysis showed that the type of varnish, the number of layers, the pre-treatment process, the wood species and direction of wood fibers significantly affect gloss of the coatings of veneered MDF panels. The type of varnish had a dominant effect on gloss. The highest gloss values were measured for the UV-varnished surface, and the lowest for WB- and PUR-varnished surfaces. Gloss was enhanced with an increase in the number of layers. Birch veneer provided higher gloss values compared to alder veneer. The gloss values measured along the wood fibers were higher than those measured across the fibers. No significant differences were found between the coatings created on sanded and thermally densified veneers for the average gloss values measured along the fibers at angles 60° and 85°. This study could have practical applications for producing value-added furniture elements using low-value wood species pre-treated by thermal compression.
Open AccessGloss of Varnished MDF Panels Veneered with Sanded and Thermally Compressed Veneer
The objective of this study was to investigate the gloss of different types of commercially manufactured varnish systems, including water-based (WB), polyurethane (PUR) and UV-cured (UV), applied on veneered MDF panels with sanded and thermally densified alder and birch wood veneers. The varnishes were applied at various numbers of layers on veneered panels. The gloss was measured at three angles of incident light: 20°, 60° and 85°. Statistical analysis showed that the type of varnish, the number of layers, the pre-treatment process, the wood species and direction of wood fibers significantly affect gloss of the coatings of veneered MDF panels. The type of varnish had a dominant effect on gloss. The highest gloss values were measured for the UV-varnished surface, and the lowest for WB- and PUR-varnished surfaces. Gloss was enhanced with an increase in the number of layers. Birch veneer provided higher gloss values compared to alder veneer. The gloss values measured along the wood fibers were higher than those measured across the fibers. No significant differences were found between the coatings created on sanded and thermally densified veneers for the average gloss values measured along the fibers at angles 60° and 85°. This study could have practical applications for producing value-added furniture elements using low-value wood species pre-treated by thermal compression.
- Open Access
Surface Roughness of Varnished Wood Pre-Treated Using Sanding and Thermal Compression
Surface roughness is an important factor during the processes of wood gluing and finishing. This study proposed a new approach for the preparation of wood veneer surfaces before varnishing through the use of thermal compression instead of sanding. The quality of the pre-treated surface was examined using surface roughness measurements. In the experiment, a wood veneer of black alder and birch, before varnishing, was subjected to sanding with a sandpaper of 180 grit size, and thermal compression at temperatures of 180 and 210 °C. Three different types of commercially manufactured varnishes (water-based (WB), polyurethane (PUR) and UV-cured (UV)) were applied to the prepared veneer surfaces with various numbers of varnish layers. Seven roughness parameters such as Ra, Rz, Rq, Rp, Rv, Rsk, and Rku were determined for the sanded and thermally densified unvarnished and varnished surfaces. The profile surface was recorded with a portable surface roughness tester along and across the wood fibers. It was found that there was no difference between the surface roughnesses of the surfaces that had been sanded and the surface roughnesses of those that had been thermally densified at a temperature of 210 °C. The research suggests that thermal compression at a temperature of 210 °C is enough to obtain smoother surfaces with a UV varnish system, and this process can be recommended as a replacement for sanding before varnishing as the most labor-intensive and expensive operations in woodworking industry. Applying two layers of varnish along with intermediate sanding was also sufficient to obtain a satisfactory finish.
Open AccessSurface Roughness of Varnished Wood Pre-Treated Using Sanding and Thermal Compression
Surface roughness is an important factor during the processes of wood gluing and finishing. This study proposed a new approach for the preparation of wood veneer surfaces before varnishing through the use of thermal compression instead of sanding. The quality of the pre-treated surface was examined using surface roughness measurements. In the experiment, a wood veneer of black alder and birch, before varnishing, was subjected to sanding with a sandpaper of 180 grit size, and thermal compression at temperatures of 180 and 210 °C. Three different types of commercially manufactured varnishes (water-based (WB), polyurethane (PUR) and UV-cured (UV)) were applied to the prepared veneer surfaces with various numbers of varnish layers. Seven roughness parameters such as Ra, Rz, Rq, Rp, Rv, Rsk, and Rku were determined for the sanded and thermally densified unvarnished and varnished surfaces. The profile surface was recorded with a portable surface roughness tester along and across the wood fibers. It was found that there was no difference between the surface roughnesses of the surfaces that had been sanded and the surface roughnesses of those that had been thermally densified at a temperature of 210 °C. The research suggests that thermal compression at a temperature of 210 °C is enough to obtain smoother surfaces with a UV varnish system, and this process can be recommended as a replacement for sanding before varnishing as the most labor-intensive and expensive operations in woodworking industry. Applying two layers of varnish along with intermediate sanding was also sufficient to obtain a satisfactory finish.
- Open Access
The Impact of Sanding and Thermal Compression of Wood, Varnish Type and Artificial Aging in Indoor Conditions on the Varnished Surface Color
The aim of this pioneering study was to compare and evaluate two different pre-treatment processes of wooden surfaces prior to varnishing by sanding or thermal compression in terms of the impact on the color characteristics of the varnished surface. In the experiment, a wood veneer of black alder and birch before varnishing was subjected to sanding with a sandpaper of 180 grit size, or thermal compression at temperatures of 180 and 210 °C. Three different kinds of commercially manufactured transparent varnish (water-based (WB) varnish, polyurethane (PUR) varnish and UV-cured (UV) varnish) were applied to the prepared veneer surfaces. The samples prepared in this way were also subjected to an artificial aging process in indoor conditions by ultraviolet light and infrared irradiation (UVL + IR). The colors of the surfaces in the CIE L*a*b* system were measured and color differences (ΔL*, Δa*, Δb* and ΔE) were determined for sanded and thermally densified, unvarnished and varnished, as well as subjected to accelerated aging surfaces. It was found that thermally densified surface-varnished veneer is more resistant to color changes during artificial aging compared to when sanded and surface-varnished. The transparent varnish systems showed better photo-stability, when thermally densified wood veneer was used as substrate than that of sanded wood. The WB varnish showed the greatest resistance to discoloration during UVL + IR irradiation, followed by PUR and UV. The preliminary findings obtained in this study indicated that replacing the sanding process with thermal compression of wood surface before varnishing could be considered as an alternative method of producing varnished panels with satisfactory color properties of surface.
Open AccessThe Impact of Sanding and Thermal Compression of Wood, Varnish Type and Artificial Aging in Indoor Conditions on the Varnished Surface Color
The aim of this pioneering study was to compare and evaluate two different pre-treatment processes of wooden surfaces prior to varnishing by sanding or thermal compression in terms of the impact on the color characteristics of the varnished surface. In the experiment, a wood veneer of black alder and birch before varnishing was subjected to sanding with a sandpaper of 180 grit size, or thermal compression at temperatures of 180 and 210 °C. Three different kinds of commercially manufactured transparent varnish (water-based (WB) varnish, polyurethane (PUR) varnish and UV-cured (UV) varnish) were applied to the prepared veneer surfaces. The samples prepared in this way were also subjected to an artificial aging process in indoor conditions by ultraviolet light and infrared irradiation (UVL + IR). The colors of the surfaces in the CIE L*a*b* system were measured and color differences (ΔL*, Δa*, Δb* and ΔE) were determined for sanded and thermally densified, unvarnished and varnished, as well as subjected to accelerated aging surfaces. It was found that thermally densified surface-varnished veneer is more resistant to color changes during artificial aging compared to when sanded and surface-varnished. The transparent varnish systems showed better photo-stability, when thermally densified wood veneer was used as substrate than that of sanded wood. The WB varnish showed the greatest resistance to discoloration during UVL + IR irradiation, followed by PUR and UV. The preliminary findings obtained in this study indicated that replacing the sanding process with thermal compression of wood surface before varnishing could be considered as an alternative method of producing varnished panels with satisfactory color properties of surface.
- Open Access
Effects of Selected Parameters on the Bonding Quality and Temperature Evolution Inside Plywood During Pressing
This research optimizes the process of plywood production to determine its effectiveness in reducing energy and adhesive consumption for more efficient production with the required quality. The influence of selected parameters including veneer treatment (non-densified and densified), plywood structure, temperature, time and pressure of pressing, on the bonding quality and temperature evolution within the veneer stacks during hot pressing was investigated. Rotary-cut, non-densified and densified birch veneers and phenol formaldehyde (PF) adhesive were used to manufacture plywood samples. The effect of pressure and time of pressing on bonding quality of the plywood was determined. Bonding quality was evaluated by determining the shear strength of the plywood samples. The temperature evolution inside the veneer stacks was measured for birch veneers for different pressing temperatures and pressures for different numbers of veneer layers. The heating rate of the veneer stacks increased as the pressing temperature increased and decreased markedly with an increasing number of veneer layers. At a high pressing pressure, the heating rate of the densified veneer stacks was faster than that of non-densified veneers at the same pressure. The use of densified veneers for the production of plywood can lead to a shorter pressing time (17–50% reduction), lower glue consumption (33.3% reduction) and a lower pressing pressure (22.2% reduction) without negatively impacting the bonding strength of the plywood.
Open AccessEffects of Selected Parameters on the Bonding Quality and Temperature Evolution Inside Plywood During Pressing
This research optimizes the process of plywood production to determine its effectiveness in reducing energy and adhesive consumption for more efficient production with the required quality. The influence of selected parameters including veneer treatment (non-densified and densified), plywood structure, temperature, time and pressure of pressing, on the bonding quality and temperature evolution within the veneer stacks during hot pressing was investigated. Rotary-cut, non-densified and densified birch veneers and phenol formaldehyde (PF) adhesive were used to manufacture plywood samples. The effect of pressure and time of pressing on bonding quality of the plywood was determined. Bonding quality was evaluated by determining the shear strength of the plywood samples. The temperature evolution inside the veneer stacks was measured for birch veneers for different pressing temperatures and pressures for different numbers of veneer layers. The heating rate of the veneer stacks increased as the pressing temperature increased and decreased markedly with an increasing number of veneer layers. At a high pressing pressure, the heating rate of the densified veneer stacks was faster than that of non-densified veneers at the same pressure. The use of densified veneers for the production of plywood can lead to a shorter pressing time (17–50% reduction), lower glue consumption (33.3% reduction) and a lower pressing pressure (22.2% reduction) without negatively impacting the bonding strength of the plywood.