Lei Ji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lei Ji has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Xiao-Chun Li
Shanghai Jiao Tong University
5 shared publications - Junfa Mao
Shanghai Jiao Tong University
4 shared publications Hong-Bin Zhu
State Key Laboratory of Radio Frequency Heterogeneous Integration, Shanghai Jiao Tong University, Shanghai, China
2 shared publicationsKen Ning
Shenzhen University,State Key Laboratory of Radio Frequency Heterogeneous Integration,Shenzhen,China
1 shared publication- Qihao Xu
State Key Laboratory of Radio Frequency Heterogeneous Integration, Shanghai Jiao Tong University, Shanghai, China
1 shared publication Xiao-Chun Li
Shanghai Jiao Tong University,State Key Laboratory of Radio Frequency Heterogeneous Integration,Shanghai,China
1 shared publication
Latest Publications
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 1003-1006
A Compact Broadband Transition From Ground Coplanar Waveguide to Folded SIW
In this letter, a compact and broadband ground coplanar waveguide (GCPW) to folded substrate-integrated waveguide (FSIW) transition is proposed by using a metallic blind via and a modified tapered strip line (TSL) in the middle layer. The modified TSL incorporates five U-shaped groove structures of different sizes and a pair of interdigital structures on a conventional tapered quarter-wavelength transformer. The subwavelength U-shaped groove structures provide a significant slow wave effect, reducing the longitudinal size of the quarter-wavelength transformer while enhancing the operating bandwidth. To verify the results, back-to-back transitions are fabricated and measured. The measurement results show that the proposed structure operates at 7.8–22.0GHz with reflection coefficient more than −10 and −10-dB fractional bandwidth (FBW) of 95%. Compared to the GCPW-to-FSIW transition using the traditional quarter-wavelength transformer, the proposed transition can increase the bandwidth and reduce the physical length of the quarter-wavelength transformer from 4.3 to 2.2mm, achieving a 49% miniaturization of the longitudinal length.
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 1003-1006
A Compact Broadband Transition From Ground Coplanar Waveguide to Folded SIW
In this letter, a compact and broadband ground coplanar waveguide (GCPW) to folded substrate-integrated waveguide (FSIW) transition is proposed by using a metallic blind via and a modified tapered strip line (TSL) in the middle layer. The modified TSL incorporates five U-shaped groove structures of different sizes and a pair of interdigital structures on a conventional tapered quarter-wavelength transformer. The subwavelength U-shaped groove structures provide a significant slow wave effect, reducing the longitudinal size of the quarter-wavelength transformer while enhancing the operating bandwidth. To verify the results, back-to-back transitions are fabricated and measured. The measurement results show that the proposed structure operates at 7.8–22.0GHz with reflection coefficient more than −10 and −10-dB fractional bandwidth (FBW) of 95%. Compared to the GCPW-to-FSIW transition using the traditional quarter-wavelength transformer, the proposed transition can increase the bandwidth and reduce the physical length of the quarter-wavelength transformer from 4.3 to 2.2mm, achieving a 49% miniaturization of the longitudinal length.
- 17 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 958-960
A Miniaturized Wilkinson Power Divider Based on Folded Spoof Surface Plasmon Polaritons
In this paper, a Wilkinson power divider (WPD) is proposed based on folded spoof surface plasmon polaritons (SSPP) transmission line, which significantly reduces the circuit size. The proposed WPD employs the folded SSPP transmission line as the power distribution section. A prototype of the WPD is fabricated under printed-circuit-board (PCB) process, with the operation band from 2.0 GHz to 2.9 GHz. Compared with the conventional WPD based on microstrip lines, the proposed WPD achieves a reduction of 52% in circuit area while maintaining similar electromagnetic performance.
- 17 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 958-960
A Miniaturized Wilkinson Power Divider Based on Folded Spoof Surface Plasmon Polaritons
In this paper, a Wilkinson power divider (WPD) is proposed based on folded spoof surface plasmon polaritons (SSPP) transmission line, which significantly reduces the circuit size. The proposed WPD employs the folded SSPP transmission line as the power distribution section. A prototype of the WPD is fabricated under printed-circuit-board (PCB) process, with the operation band from 2.0 GHz to 2.9 GHz. Compared with the conventional WPD based on microstrip lines, the proposed WPD achieves a reduction of 52% in circuit area while maintaining similar electromagnetic performance.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 13 (5) , 594-603
A Slow Wave Folded Ridge HMSIW Using Spoof Surface Plasmon Polaritons Structure and Its Application in Coupler Design
In this article, a folded ridge half-mode substrate integrated waveguide (FRHMSIW) combined with the novel spoof surface plasmon polaritons (SSPP) is proposed to reduce both the lateral size and the longitudinal size. The SSPP structure consisting of sub-wavelength U-shaped grooves, metal patches and metal blind holes is loaded into the FRHMSIW. Firstly, the SSPP increases the effective permeability and permittivity in the waveguide, which can decrease the cutoff frequency and hence reduce the lateral size. Secondly, the SSPP has slow-wave effect, which can reduce the longitudinal size of the waveguide. Analytical formulas of the effective permeability and permittivity are derived based on anisotropic media theory, which are verified by comparing the calculation results with full wave simulation results. According to the derived analytical formulas, a prototype of the proposed FRHMSIW-SSPP waveguide is designed and fabricated using the PCB process. The measurement results show that the proposed waveguide reduces lateral width by 78.7% and the longitudinal dimension by more than 74% compared with the classical SIW with the same cutoff frequency. Subsequently, the FRHMSIW-SSPP structure is applied to design a 3-dB coupler. Results show that the coupler based on the FRHMSIW-SSPP can reduce the surface area by 92.5% compared with the classical SIW coupler.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 13 (5) , 594-603
A Slow Wave Folded Ridge HMSIW Using Spoof Surface Plasmon Polaritons Structure and Its Application in Coupler Design
In this article, a folded ridge half-mode substrate integrated waveguide (FRHMSIW) combined with the novel spoof surface plasmon polaritons (SSPP) is proposed to reduce both the lateral size and the longitudinal size. The SSPP structure consisting of sub-wavelength U-shaped grooves, metal patches and metal blind holes is loaded into the FRHMSIW. Firstly, the SSPP increases the effective permeability and permittivity in the waveguide, which can decrease the cutoff frequency and hence reduce the lateral size. Secondly, the SSPP has slow-wave effect, which can reduce the longitudinal size of the waveguide. Analytical formulas of the effective permeability and permittivity are derived based on anisotropic media theory, which are verified by comparing the calculation results with full wave simulation results. According to the derived analytical formulas, a prototype of the proposed FRHMSIW-SSPP waveguide is designed and fabricated using the PCB process. The measurement results show that the proposed waveguide reduces lateral width by 78.7% and the longitudinal dimension by more than 74% compared with the classical SIW with the same cutoff frequency. Subsequently, the FRHMSIW-SSPP structure is applied to design a 3-dB coupler. Results show that the coupler based on the FRHMSIW-SSPP can reduce the surface area by 92.5% compared with the classical SIW coupler.
- 22 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (9) , 1035-1038
Two-Material-Filled Ridge Half-Mode Substrate Integrated Waveguide for Monomode Bandwidth Enhancement
In this letter, a two-material-filled ridge half-mode substrate integrated waveguide (2M-RHMSIW) is proposed for monomode bandwidth (MMB) enhancement. The cutoff frequency of the dominant mode decreases with the permittivity of the material filling in the bottom layer increasing. The cutoff frequency of the second mode increases as the permittivity of the material filled in the top layer decreases. Therefore, the proposed structure uses low-permittivity material for the top substrate layer and high-permittivity material for the bottom substrate layer, to widen the MMB. In addition, a series of air holes are drilled in the top substrate layer to reduce its effective permittivity, which further widens the MMB. A prototype of the proposed structure is fabricated under PCB process, which MMB is from 2 to 14 GHz.
- 22 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (9) , 1035-1038
Two-Material-Filled Ridge Half-Mode Substrate Integrated Waveguide for Monomode Bandwidth Enhancement
In this letter, a two-material-filled ridge half-mode substrate integrated waveguide (2M-RHMSIW) is proposed for monomode bandwidth (MMB) enhancement. The cutoff frequency of the dominant mode decreases with the permittivity of the material filling in the bottom layer increasing. The cutoff frequency of the second mode increases as the permittivity of the material filled in the top layer decreases. Therefore, the proposed structure uses low-permittivity material for the top substrate layer and high-permittivity material for the bottom substrate layer, to widen the MMB. In addition, a series of air holes are drilled in the top substrate layer to reduce its effective permittivity, which further widens the MMB. A prototype of the proposed structure is fabricated under PCB process, which MMB is from 2 to 14 GHz.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (6) , 1818-1825
A Slow Wave Ridged Half-Mode Substrate Integrated Waveguide With Spoof Surface Plasmon Polaritons
In this article, a slow wave (SW) ridged half-mode substrate integrated waveguide (RHMSIW) combined with spoof surface plasmon polaritons (SSPPs) structure is proposed. The SW feature is achieved by integrating the SSPP structure into the metal ridge of RHMSIW. Besides, the proposed structure has a compact lateral size because the ridge of the RHMSIW introduces a step capacitance in the waveguide. Due to the loading of the SSPP structure, the proposed RHMSIW-SSPP structure has the ability of strong electric field confinement. Compared with the RHMSIW structure, the proposed RHMSIW-SSPP structure has a low crosstalk feature. A prototype of the proposed RHMSIW-SSPP structure with band-pass 4.5-14 GHz is designed and fabricated under PCB process. The proposed RHMSIW-SSPP structure reduces the longitudinal size over 50% and the lateral width by 40% compared with the HMSIW, and reduces the longitudinal size over 50% and the transverse width by 70% compared with the SIW. Therefore, the proposed structure has potential applications in miniaturized microwave and RF systems.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (6) , 1818-1825
A Slow Wave Ridged Half-Mode Substrate Integrated Waveguide With Spoof Surface Plasmon Polaritons
In this article, a slow wave (SW) ridged half-mode substrate integrated waveguide (RHMSIW) combined with spoof surface plasmon polaritons (SSPPs) structure is proposed. The SW feature is achieved by integrating the SSPP structure into the metal ridge of RHMSIW. Besides, the proposed structure has a compact lateral size because the ridge of the RHMSIW introduces a step capacitance in the waveguide. Due to the loading of the SSPP structure, the proposed RHMSIW-SSPP structure has the ability of strong electric field confinement. Compared with the RHMSIW structure, the proposed RHMSIW-SSPP structure has a low crosstalk feature. A prototype of the proposed RHMSIW-SSPP structure with band-pass 4.5-14 GHz is designed and fabricated under PCB process. The proposed RHMSIW-SSPP structure reduces the longitudinal size over 50% and the lateral width by 40% compared with the HMSIW, and reduces the longitudinal size over 50% and the transverse width by 70% compared with the SIW. Therefore, the proposed structure has potential applications in miniaturized microwave and RF systems.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2539-2550
Half-Mode Substrate Integrated Waveguide Dispersion Tailoring Using 2.5-D Spoof Surface Plasmon Polaritons Structure
In this article, a half-mode substrate integrated waveguide (HMSIW) combined with 2.5-D spoof surface plasmon polaritons (SPPs) structure is proposed to tailor the dispersion features and cutoff frequency of the HMSIW. The proposed HMSIW-SPP structure has a smaller longitudinal dimension since the dispersion of the proposed structure can be tailored by adjusting the geometric parameters of the 2.5-D spoof SPP arbitrary. Simultaneously, the proposed structure has a smaller lateral width than that of the classical HMSIW because the 2.5-D spoof SPP introduces extra capacitance in the waveguide. Moreover, an equivalent circuit model is proposed and used to analyze the design principles. The structure exhibiting the cutoff frequency of 6.0 GHz is designed and fabricated under the printed circuit board process. Measurement and simulation results show that the proposed HMSIW-SPP structure decreases the longitudinal dimension by more than 50% and the lateral width by 25% without sacrificing its transmission performance. Due to the reduced cutoff frequency and effective wavelength, the proposed structure enables extreme miniaturization and can be applied in the design of miniaturized microwave circuits.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (7) , 2539-2550
Half-Mode Substrate Integrated Waveguide Dispersion Tailoring Using 2.5-D Spoof Surface Plasmon Polaritons Structure
In this article, a half-mode substrate integrated waveguide (HMSIW) combined with 2.5-D spoof surface plasmon polaritons (SPPs) structure is proposed to tailor the dispersion features and cutoff frequency of the HMSIW. The proposed HMSIW-SPP structure has a smaller longitudinal dimension since the dispersion of the proposed structure can be tailored by adjusting the geometric parameters of the 2.5-D spoof SPP arbitrary. Simultaneously, the proposed structure has a smaller lateral width than that of the classical HMSIW because the 2.5-D spoof SPP introduces extra capacitance in the waveguide. Moreover, an equivalent circuit model is proposed and used to analyze the design principles. The structure exhibiting the cutoff frequency of 6.0 GHz is designed and fabricated under the printed circuit board process. Measurement and simulation results show that the proposed HMSIW-SPP structure decreases the longitudinal dimension by more than 50% and the lateral width by 25% without sacrificing its transmission performance. Due to the reduced cutoff frequency and effective wavelength, the proposed structure enables extreme miniaturization and can be applied in the design of miniaturized microwave circuits.