Andreas Lümkemann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Andreas Lümkemann has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Andrei Bogatov
Department of Mechanical and Industrial Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
3 shared publications - Asad Alamgir
Department of Mechanical and Industrial Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
3 shared publications - Fjodor Sergejev
Department of Mechanical and Industrial Engineering Tallinn University of Technology Ehitajate tee 5 19086 Tallinn Estonia
3 shared publications - Mart Viljus
Department of Mechanical and Industrial Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
3 shared publications - Vitali Podgursky
Department of Mechanical and Industrial Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
3 shared publications - Hamid Bolvardi
PLATIT AG
2 shared publications
Latest Publications
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 450, 61-70
Influence of the Crystal Structure of AlCrN on Tool Coating Properties and Wear in Dry Gear Hobbing
Dry machining of gears demands advanced coating technologies to withstand high thermal and mechanical stresses. In this study, AlCrN coatings were deposited using the newly developed Focused Magnetron Sputtering (FMS) process and compared with conventional Cathodic Arc Evaporation (CAE)-AlCrN and boroncontaining CAE-AlCrBN coatings. XRD analysis showed that FMS produced a finegrained crystal structure with half the full width at half maximum (FWHM) of CAE-AlCrN. Stressoptimised deposition allowed a 60 % higher coating thickness with improved adhesion. Analogy gear hobbing tests (fly cutting tests) demonstrated that FMS-AlCrN had 52 % lower crater wear than CAE-AlCrN, while CAE-AlCrBN also improved crater wear resistance due to boroninduced grain refinement. However, both finegrained coatings exhibited increased flank wear compared to the coarse-grained CAE-AlCrN coating. The results show that FMS enables the production of dense, fine-grained coatings with superior adhesion and crater wear resistance, highlighting its potential for dry gear hobbing. Further optimisation of hardness and microstructure is required to balance crater and flank wear behaviour.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 450, 61-70
Open AccessInfluence of the Crystal Structure of AlCrN on Tool Coating Properties and Wear in Dry Gear Hobbing
Dry machining of gears demands advanced coating technologies to withstand high thermal and mechanical stresses. In this study, AlCrN coatings were deposited using the newly developed Focused Magnetron Sputtering (FMS) process and compared with conventional Cathodic Arc Evaporation (CAE)-AlCrN and boroncontaining CAE-AlCrBN coatings. XRD analysis showed that FMS produced a finegrained crystal structure with half the full width at half maximum (FWHM) of CAE-AlCrN. Stressoptimised deposition allowed a 60 % higher coating thickness with improved adhesion. Analogy gear hobbing tests (fly cutting tests) demonstrated that FMS-AlCrN had 52 % lower crater wear than CAE-AlCrN, while CAE-AlCrBN also improved crater wear resistance due to boroninduced grain refinement. However, both finegrained coatings exhibited increased flank wear compared to the coarse-grained CAE-AlCrN coating. The results show that FMS enables the production of dense, fine-grained coatings with superior adhesion and crater wear resistance, highlighting its potential for dry gear hobbing. Further optimisation of hardness and microstructure is required to balance crater and flank wear behaviour.
- Open Access
Dynamic Impact Resistance and Scratch Adhesion of AlCrN Coatings Sputtered Using Cathodic Arc Glow Discharge
AlCrN coatings, which are characterized by high hardness and good wear resistance, are often used for drilling, milling, and punching tools. Therefore, the study of the behaviour of these coatings under cyclic impact loading is essential for their optimization. Our previous work has focused on the study of the composition and microstructure of AlCrN coatings prepared using a cathodic arc deposition system with a SCIL® controller that controls the average ion energy per deposited atom (Ed). Two sets of coatings were prepared in two different modes, with a metal target and with a poisoned target. The chemical compositions of the coatings were very similar regardless of their deposition conditions, but the structure and mechanical properties of the coatings depended strongly on Ed. The present work focused on the scratch adhesion and impact wear of these two sets of AlCrN coatings. The lifetimes of both sets of samples under repeated dynamic impacts were tested using a dynamic impact tester with a WC-Co ball. It was shown that the impact behaviour of the coatings prepared in the metallic regime does not depend on the deposition conditions. However, the impact behaviour of the coatings deposited in poisoned mode was improved by increasing Ed.
Open AccessDynamic Impact Resistance and Scratch Adhesion of AlCrN Coatings Sputtered Using Cathodic Arc Glow Discharge
AlCrN coatings, which are characterized by high hardness and good wear resistance, are often used for drilling, milling, and punching tools. Therefore, the study of the behaviour of these coatings under cyclic impact loading is essential for their optimization. Our previous work has focused on the study of the composition and microstructure of AlCrN coatings prepared using a cathodic arc deposition system with a SCIL® controller that controls the average ion energy per deposited atom (Ed). Two sets of coatings were prepared in two different modes, with a metal target and with a poisoned target. The chemical compositions of the coatings were very similar regardless of their deposition conditions, but the structure and mechanical properties of the coatings depended strongly on Ed. The present work focused on the scratch adhesion and impact wear of these two sets of AlCrN coatings. The lifetimes of both sets of samples under repeated dynamic impacts were tested using a dynamic impact tester with a WC-Co ball. It was shown that the impact behaviour of the coatings prepared in the metallic regime does not depend on the deposition conditions. However, the impact behaviour of the coatings deposited in poisoned mode was improved by increasing Ed.
- Open Access
High-Temperature Oxidation Resistance and Tribological Properties of Al2O3/ta-C Coating
The focus is on the oxidation resistance and tribological performance of ta-C and Al2O3/ta-C coatings. The wear tests were carried out on the ball on disc tribometer at room (25 °C) and high (400, 450 and 500 °C) temperatures in ambient air with Si3N4 balls as counterbodies. Scanning electron microscopy and Raman spectroscopy were used to analyze the surface morphology and chemical bonding, respectively. The Al2O3/ta-C coating exhibited better oxidation resistance and tribological performance at elevated temperatures than the ta-C coating. The Raman analysis revealed that a thin alumina layer suppresses structural changes in the ta-C coating at elevated temperatures, thus preserving the sp3 content.
Open AccessHigh-Temperature Oxidation Resistance and Tribological Properties of Al2O3/ta-C Coating
The focus is on the oxidation resistance and tribological performance of ta-C and Al2O3/ta-C coatings. The wear tests were carried out on the ball on disc tribometer at room (25 °C) and high (400, 450 and 500 °C) temperatures in ambient air with Si3N4 balls as counterbodies. Scanning electron microscopy and Raman spectroscopy were used to analyze the surface morphology and chemical bonding, respectively. The Al2O3/ta-C coating exhibited better oxidation resistance and tribological performance at elevated temperatures than the ta-C coating. The Raman analysis revealed that a thin alumina layer suppresses structural changes in the ta-C coating at elevated temperatures, thus preserving the sp3 content.
- Open Access
High-Temperature Tribological Performance of Al2O3/a-C:H:Si Coating in Ambient Air
The study investigates thermal stability and high temperature tribological performance of a-C:H:Si diamond-like carbon (DLC) coating. A thin alumina layer was deposited on top of the a-C:H:Si coating to improve the tribological performance at high temperatures. The a-C:H:Si coating and alumina layer were prepared using plasma-activated chemical vapour deposition and atomic layer deposition, respectively. Raman and X-ray photoelectron spectroscopy were used to investigate the structures and chemical compositions of the specimens. The D and G Raman peaks due to sp2 bonding and the peaks corresponding to the trans-polyacetylene (t-Pa) and sp bonded chains were identified in the Raman spectra of the a-C:H:Si coating. Ball-on-disc sliding tests were carried out at room temperature and 400 °C using Si3N4 balls as counter bodies. The a-C:H:Si coating failed catastrophically in sliding tests at 400 °C; however, a repeatable and reproducible regime of sliding with a low coefficient of friction was observed for the Al2O3/a-C:H:Si coating at the same temperature. The presence of the alumina layer and high stress and temperature caused structural changes in the bulk a-C:H:Si and top layers located near the contact area, leading to the modification of the contact conditions, delivering of extra oxygen into the contact area, reduction of hydrogen effusion, and suppression of the atmospheric oxidation.
Open AccessHigh-Temperature Tribological Performance of Al2O3/a-C:H:Si Coating in Ambient Air
The study investigates thermal stability and high temperature tribological performance of a-C:H:Si diamond-like carbon (DLC) coating. A thin alumina layer was deposited on top of the a-C:H:Si coating to improve the tribological performance at high temperatures. The a-C:H:Si coating and alumina layer were prepared using plasma-activated chemical vapour deposition and atomic layer deposition, respectively. Raman and X-ray photoelectron spectroscopy were used to investigate the structures and chemical compositions of the specimens. The D and G Raman peaks due to sp2 bonding and the peaks corresponding to the trans-polyacetylene (t-Pa) and sp bonded chains were identified in the Raman spectra of the a-C:H:Si coating. Ball-on-disc sliding tests were carried out at room temperature and 400 °C using Si3N4 balls as counter bodies. The a-C:H:Si coating failed catastrophically in sliding tests at 400 °C; however, a repeatable and reproducible regime of sliding with a low coefficient of friction was observed for the Al2O3/a-C:H:Si coating at the same temperature. The presence of the alumina layer and high stress and temperature caused structural changes in the bulk a-C:H:Si and top layers located near the contact area, leading to the modification of the contact conditions, delivering of extra oxygen into the contact area, reduction of hydrogen effusion, and suppression of the atmospheric oxidation.
- Open Access
High-Temperature Tribological Performance of Hard Multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN Coating Deposited on WC-Co Substrate
Mechanical and tribological properties of the hard-multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN coating deposited on WC-Co substrate were investigated. The sliding tests were carried out using ball-on-disc tribometer at room (25 °C) and high temperatures (600 and 800 °C) with Al2O3 balls as counterpart. Nano-scratch tests were performed at room temperature with a sphero-conical diamond indenter. The surface morphology and chemical composition were investigated with scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS) and in-situ high-temperature X-ray diffraction (HT-XRD). The phase transition from fcc-(Al,Cr)2O3 into α-(Al,Cr)2O3 was observed at about 800 °C. The results of the tribological tests depends on the temperature, the lowest apparent and real wear volumes were observed on the coating after the test at 800 °C along with the smallest coefficient of friction (COF). The plastic deformation of the coating was confirmed in sliding and nano-scratch tests. The nano-scratch tests revealed the dependence of COF value on the temperature of the sliding tests.
Open AccessHigh-Temperature Tribological Performance of Hard Multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN Coating Deposited on WC-Co Substrate
Mechanical and tribological properties of the hard-multilayer TiN-AlTiN/nACo-CrN/AlCrN-AlCrO-AlTiCrN coating deposited on WC-Co substrate were investigated. The sliding tests were carried out using ball-on-disc tribometer at room (25 °C) and high temperatures (600 and 800 °C) with Al2O3 balls as counterpart. Nano-scratch tests were performed at room temperature with a sphero-conical diamond indenter. The surface morphology and chemical composition were investigated with scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS) and in-situ high-temperature X-ray diffraction (HT-XRD). The phase transition from fcc-(Al,Cr)2O3 into α-(Al,Cr)2O3 was observed at about 800 °C. The results of the tribological tests depends on the temperature, the lowest apparent and real wear volumes were observed on the coating after the test at 800 °C along with the smallest coefficient of friction (COF). The plastic deformation of the coating was confirmed in sliding and nano-scratch tests. The nano-scratch tests revealed the dependence of COF value on the temperature of the sliding tests.
- Open Access
Comparison of Lifetime of the PVD Coatings in Laboratory Dynamic Impact Test and Industrial Fine Blanking Process
Protective hard PVD coatings are used to improve the endurance of the tools exposed to repeated impact load, e.g., fine blanking punches. During the fine blanking process, a coated punch repeatedly impacts sheet metal. Thus, the coating which protects the punch surface is exposed to the dynamic impact load. On the other hand, the laboratory method of dynamic impact testing is well known and used for the development and optimization of protective coatings. This paper is focused on the comparison of tool life and lifetime of the industrial prepared PVD coatings exposed to repeated dynamic impact load in the industrial fine blanking process and the laboratory dynamic impact testing. Three different types of protective coatings were tested and the results were discussed. It was shown that the lifetime of coated specimens in both the fine blanking and the dynamic impact processes was influenced by similar mechanical properties of the protective coatings. The qualitative comparison shows that the lifetime obtained by the dynamic impact test was the same as the lifetime obtained by the industrial fine blanking process. The laboratory impact test appears to be a suitable alternative for the optimisation and development of protective PVD coatings for punches used in the industrial fine blanking process.
Open AccessComparison of Lifetime of the PVD Coatings in Laboratory Dynamic Impact Test and Industrial Fine Blanking Process
Protective hard PVD coatings are used to improve the endurance of the tools exposed to repeated impact load, e.g., fine blanking punches. During the fine blanking process, a coated punch repeatedly impacts sheet metal. Thus, the coating which protects the punch surface is exposed to the dynamic impact load. On the other hand, the laboratory method of dynamic impact testing is well known and used for the development and optimization of protective coatings. This paper is focused on the comparison of tool life and lifetime of the industrial prepared PVD coatings exposed to repeated dynamic impact load in the industrial fine blanking process and the laboratory dynamic impact testing. Three different types of protective coatings were tested and the results were discussed. It was shown that the lifetime of coated specimens in both the fine blanking and the dynamic impact processes was influenced by similar mechanical properties of the protective coatings. The qualitative comparison shows that the lifetime obtained by the dynamic impact test was the same as the lifetime obtained by the industrial fine blanking process. The laboratory impact test appears to be a suitable alternative for the optimisation and development of protective PVD coatings for punches used in the industrial fine blanking process.