Robert J. Dengler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Robert J. Dengler has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Ken B. Cooper
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
5 shared publications Raquel Rodriguez Monje
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
4 shared publications- Corey Jonathan Cochrane
NASA Jet Propulsion Laboratory California Institute of Technology Pasadena CA USA
2 shared publications - Jose V. Siles
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
2 shared publications - Luis Millán
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, USA
2 shared publications - Peter H. Siegel
California Institute of Technology, Pasadena, CA, USA
2 shared publications
Latest Publications
- Open Access
- 23 October 2023
- Published by Copernicus GmbH
- Vol. 2023, 1-31
Comment on egusphere-2023-1807
NASA’s Vapor In-cloud Profiling Radar (VIPR) is a tunable G-band radar designed for in-cloud and precipitation humidity remote sensing. VIPR estimates humidity using the differential absorption radar (DAR) technique. This technique exploits the difference between atmospheric attenuation at different frequencies (“on” and “off” an absorption line) and combines it with the ranging capabilities of the radar to estimate the absorbing gas concentration along the radar path. We analyze the VIPR humidity measurements during two NASA field campaigns: (1) the Investigation of Microphysics and Precipitation for Atlantic Coast-Threatening Snowstorms (IMPACTS) campaign, with the objective of studying wintertime snowstorms focusing on East Coast cyclones; and (2) the Synergies Of Active optical and Active microwave Remote Sensing Experiment (SOA2RSE) campaign which studied the synergy between DAR (VIPR) and differential absorption lidar (DIAL, the High altitude Lidar Observatory – HALO) measurements. We discuss a comparison with dropsondes launched during these campaigns as well as an intercomparison against the ERA5 reanalysis fields. Thus, this study serves as an additional evaluation of ERA5 lower tropospheric humidity fields. In addition, we show a smooth transition in water vapor profiles between the in-cloud and clear-sky measurements obtained from VIPR and HALO respectively, which highlights the complementary nature of these two measurement techniques for future airborne and space-based missions.
- 23 October 2023
- Published by Copernicus GmbH
- Vol. 2023, 1-31
Open AccessComment on egusphere-2023-1807
NASA’s Vapor In-cloud Profiling Radar (VIPR) is a tunable G-band radar designed for in-cloud and precipitation humidity remote sensing. VIPR estimates humidity using the differential absorption radar (DAR) technique. This technique exploits the difference between atmospheric attenuation at different frequencies (“on” and “off” an absorption line) and combines it with the ranging capabilities of the radar to estimate the absorbing gas concentration along the radar path. We analyze the VIPR humidity measurements during two NASA field campaigns: (1) the Investigation of Microphysics and Precipitation for Atlantic Coast-Threatening Snowstorms (IMPACTS) campaign, with the objective of studying wintertime snowstorms focusing on East Coast cyclones; and (2) the Synergies Of Active optical and Active microwave Remote Sensing Experiment (SOA2RSE) campaign which studied the synergy between DAR (VIPR) and differential absorption lidar (DIAL, the High altitude Lidar Observatory – HALO) measurements. We discuss a comparison with dropsondes launched during these campaigns as well as an intercomparison against the ERA5 reanalysis fields. Thus, this study serves as an additional evaluation of ERA5 lower tropospheric humidity fields. In addition, we show a smooth transition in water vapor profiles between the in-cloud and clear-sky measurements obtained from VIPR and HALO respectively, which highlights the complementary nature of these two measurement techniques for future airborne and space-based missions.
- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 60 (01962892) , 1-15
First Airborne Measurements With a G-Band Differential Absorption Radar
Observations and analysis from the first airborne deployment of a G-band atmospheric radar, the Jet Propulsion Laboratory’s vapor in-cloud profiling radar (VIPR), are presented with a focus on ocean surface scatterometry and water vapor retrievals using the differential absorption radar (DAR) technique. We assess transceiver cross-calibration stability between the two DAR frequency channels using a combination of ground-based calibration measurements and airborne cloud observations that are validated by independent sensors. By comparing calibrated, unattenuated ocean surface backscatter measurements with existing models, we demonstrate the need for improvements in treating ocean surface scattering at G-band frequencies for future in-flight radar calibration applications. During science-oriented flights off the coast of California, we demonstrate partial column integrated water vapor (IWV) measurement capabilities with 0.3-mm precision in clear sky by performing a descent maneuver over an operational radiosonde (RS) launching site and comparing with the coincident in situ profiles to find a root mean square error (RMSE) of 0.5 mm. Furthermore, we present water vapor profiling and IWV measurements in the presence of clouds and precipitation when flying through a frontal weather system in the vicinity of Bodega Bay. By comparing with coincident RS profiles, we find an RMSE for in-cloud humidity profile retrievals of 1.1${\rm gm}^{-3}$ and precision of 0.6${\rm gm}^{-3}$ while the IWV retrievals reveal a bias from differential hydrometeor extinction of 5 mm. We provide a critical assessment of cloud-scattering-induced biases in the water vapor retrievals, as well as discuss a potential method for eliminating systematic error from the DAR measurements.- 16 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 60 (01962892) , 1-15
First Airborne Measurements With a G-Band Differential Absorption Radar
Observations and analysis from the first airborne deployment of a G-band atmospheric radar, the Jet Propulsion Laboratory’s vapor in-cloud profiling radar (VIPR), are presented with a focus on ocean surface scatterometry and water vapor retrievals using the differential absorption radar (DAR) technique. We assess transceiver cross-calibration stability between the two DAR frequency channels using a combination of ground-based calibration measurements and airborne cloud observations that are validated by independent sensors. By comparing calibrated, unattenuated ocean surface backscatter measurements with existing models, we demonstrate the need for improvements in treating ocean surface scattering at G-band frequencies for future in-flight radar calibration applications. During science-oriented flights off the coast of California, we demonstrate partial column integrated water vapor (IWV) measurement capabilities with 0.3-mm precision in clear sky by performing a descent maneuver over an operational radiosonde (RS) launching site and comparing with the coincident in situ profiles to find a root mean square error (RMSE) of 0.5 mm. Furthermore, we present water vapor profiling and IWV measurements in the presence of clouds and precipitation when flying through a frontal weather system in the vicinity of Bodega Bay. By comparing with coincident RS profiles, we find an RMSE for in-cloud humidity profile retrievals of 1.1${\rm gm}^{-3}$ and precision of 0.6${\rm gm}^{-3}$ while the IWV retrievals reveal a bias from differential hydrometeor extinction of 5 mm. We provide a critical assessment of cloud-scattering-induced biases in the water vapor retrievals, as well as discuss a potential method for eliminating systematic error from the DAR measurements.- 19 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (11) , 5865-5875
A Compact, Low Power Consumption, and Highly Sensitive 95 GHz Doppler Radar
We report on the architecture and performance of a highly sensitive 95 GHz Doppler radar instrument with 0.6 Watt transmit power designed for low power consumption and small size. The radar’s sensitivity is validated using a calibration target, and its remote sensing capabilities are demonstrated through the detection of clouds, rain, insects, and distant vehicles. The radar uses a frequency-modulated continuous-wave (FMCW) waveform, a single antenna with ultra-high-isolation quasioptical transmit/receive duplexing, an InP low-noise amplifier for receiving, and a GaN power amplifier for transmitting. A DC power consumption of 22 W for the RF and digital subsystems is achieved, in part, by a combination of a power-efficient waveform generation/detection and signal processing board and a CMOS-based system-on-chip W-band oscillator. Excluding power supplies and a computer interface, the radar system mass is under 6 kg, making it attractive for future deployment from platforms with constrained accommodation resources.
- 19 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (11) , 5865-5875
A Compact, Low Power Consumption, and Highly Sensitive 95 GHz Doppler Radar
We report on the architecture and performance of a highly sensitive 95 GHz Doppler radar instrument with 0.6 Watt transmit power designed for low power consumption and small size. The radar’s sensitivity is validated using a calibration target, and its remote sensing capabilities are demonstrated through the detection of clouds, rain, insects, and distant vehicles. The radar uses a frequency-modulated continuous-wave (FMCW) waveform, a single antenna with ultra-high-isolation quasioptical transmit/receive duplexing, an InP low-noise amplifier for receiving, and a GaN power amplifier for transmitting. A DC power consumption of 22 W for the RF and digital subsystems is achieved, in part, by a combination of a power-efficient waveform generation/detection and signal processing board and a CMOS-based system-on-chip W-band oscillator. Excluding power supplies and a computer interface, the radar system mass is under 6 kg, making it attractive for future deployment from platforms with constrained accommodation resources.
- 29 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 58 (8) , 5552-5563
An FPGA-Based Signal Processor for FMCW Doppler Radar and Spectroscopy
We report on the design and development of a field programmable gate array (FPGA)-based radar and spectrometer signal processor. It leverages an efficient implementation of a fixed-point frequency-modulated continuous-wave (FMCW) Doppler radar algorithm and has been demonstrated in a short-range W-band radar system developed for mapping plume and jet phenomena in the solar system. The signal processor also performs Fourier transform-based spectroscopy with a resolution, bandwidth, and averaging time appropriate for millimeter- and submillimeter-wave passive remote sensing in space. With a dc power consumption totaling only 3 W, the processor helps make the Doppler radar and spectrometer instrument well-suited for spaceborne, airborne, or portable platforms. Here, we describe the fixed-point implementation of the radar and spectrometer algorithm, emphasizing its computational efficiency for low resource utilization, and provide examples of Doppler radar sensing of rain and spectrometer sensitivity to hot and cold blackbody loads.
- 29 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 58 (8) , 5552-5563
An FPGA-Based Signal Processor for FMCW Doppler Radar and Spectroscopy
We report on the design and development of a field programmable gate array (FPGA)-based radar and spectrometer signal processor. It leverages an efficient implementation of a fixed-point frequency-modulated continuous-wave (FMCW) Doppler radar algorithm and has been demonstrated in a short-range W-band radar system developed for mapping plume and jet phenomena in the solar system. The signal processor also performs Fourier transform-based spectroscopy with a resolution, bandwidth, and averaging time appropriate for millimeter- and submillimeter-wave passive remote sensing in space. With a dc power consumption totaling only 3 W, the processor helps make the Doppler radar and spectrometer instrument well-suited for spaceborne, airborne, or portable platforms. Here, we describe the fixed-point implementation of the radar and spectrometer algorithm, emphasizing its computational efficiency for low resource utilization, and provide examples of Doppler radar sensing of rain and spectrometer sensitivity to hot and cold blackbody loads.
- 1 January 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10975659,p. 1-3
A 600 GHz imaging radar for concealed objects detection
We present the hardware and the experimental results from a 600 GHz imaging radar with sub-centimeter resolution in all three spatial dimensions. The FMCW radar transceiver is built on a back-end of commercial microwave components - with a front-end of custom designed frequency multipliers and mixers. The optics consists of a 40 cm diameter ellipsoidal primary reflector with a 4 m focal length. The acquired images will be compared with those achieved with a more traditional sub-millimeter wave active imaging technique.
- 1 January 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10975659,p. 1-3
A 600 GHz imaging radar for concealed objects detection
We present the hardware and the experimental results from a 600 GHz imaging radar with sub-centimeter resolution in all three spatial dimensions. The FMCW radar transceiver is built on a back-end of commercial microwave components - with a front-end of custom designed frequency multipliers and mixers. The optics consists of a 40 cm diameter ellipsoidal primary reflector with a 4 m focal length. The acquired images will be compared with those achieved with a more traditional sub-millimeter wave active imaging technique.
- 4 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 555-556
Applications & early results from THz heterodyne imaging at 119μm
The authors present a description and early measurement results from a unique CW terahertz heterodyne imaging system based around two custom fabricated 2.5 THz planar Schottky diode mixers and two commercially available optically pumped far IR lasers. One laser is used for the signal beam and supplies as much as 70 mW at 2.5 THz. The other laser acts as a local oscillator source for the two mixers. The system uses the second THz mixer, a low frequency reference oscillator and a lock-in amplifier to monitor and normalise the two lasers. The system has been employed on both biological tissues as well as materials of interest to NASA space science applications. The instrumentation is briefly described and some representative images is also presented.
- 4 October 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 555-556
Applications & early results from THz heterodyne imaging at 119μm
The authors present a description and early measurement results from a unique CW terahertz heterodyne imaging system based around two custom fabricated 2.5 THz planar Schottky diode mixers and two commercially available optically pumped far IR lasers. One laser is used for the signal beam and supplies as much as 70 mW at 2.5 THz. The other laser acts as a local oscillator source for the two mixers. The system uses the second THz mixer, a low frequency reference oscillator and a lock-in amplifier to monitor and normalise the two lasers. The system has been employed on both biological tissues as well as materials of interest to NASA space science applications. The instrumentation is briefly described and some representative images is also presented.