FRFeliks Ya. Rudik

Feliks Ya. Rudik

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Feliks Ya. Rudik has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    HEAT TREATMENT TECHNOLOGICAL FEATURES OF MEAT AND BONE RAW MATERIALS IN PACKAGED BROTH PRODUCTION

    by Olga Fomenko, Ayazhan Sagingalieva, Natalya Morgunova, Felix Rudik

    The aim of the study is to investigate and substantiate thermophysical processes in the production of liquid packaged fast-food broths with a long shelf life. The heat capacity of water decreased when heated from 0 to 37 °C, with further heating it increased, but insignificantly in its absolute value. This circumstance allowed us to conclude that it is possible to use preheated water to 70 °C outside the digester. This significantly reduces the negative impact of prolonged exposure to high temperatures on mass transfer processes. It was experimentally established that an increase in the water heating temperature in the range from 80 to 100 °C increases the thermal conductivity index by only 6 %, and then it remains virtually unchanged. The intensity of heat transfer from hotter to colder layers of water as a result of thermal interaction of water molecules acquires a linear pattern. This does not increase the intensity of mass transfer processes and, accordingly, does not increase the efficiency of heat transfer in meat and bone raw materials. Along with the water heating temperature, one of the key factors influencing the heating rate of meat and bone raw materials during cooking is the heating duration. It depends on the volume of pieces of meat and bone, as well as on the individual surface areas of bodies. As a result, knowing and taking into account the influence of thermophysical characteristics on the process of heating meat and bone raw materials with a heat carrier, it is possible to effectively control the process of cooking broth. In technological terms, this pattern allows improving the quality of products, increasing the productivity of the flow-technological line and optimizing energy costs for hydrothermal processes, ensuring the production of finished products with high consumer characteristics.


  • Open Access

    MICROBIAL SAFETY ISSUES IN INSTANT PACKAGED MEAT AND BONE BROTHS: PREDICTING THE RISKS OF OCCURRENCE

    by Ольга Сергеевна Фоменко, Аяжан Галиевна Сагингалиева, Феликс Яковлевич Рудик, Лидия Владимировна Карпунина

    The production of long-term storage meat products is associated with limitations related primarily to its susceptibility to initial microbiological contamination with pathogenic and opportunistic microorganisms, subsequent development at all stages of storage and processing. Endogenous development of microorganisms in meat with all internal and external processes of animal development in the pre-slaughter and post-slaughter state intensify their development, including at all stages of subsequent processing, including production stages. One of the possible solutions to this problem is the development of a technological process for the production of long-term storage products using barrier technologies at all stages of processing and production, which will ensure increased sanitary and hygienic requirements and inactivation of microorganisms. The materials present an analysis of possible sources of contamination of meat raw materials during slaughter, production and processing. The predominant microflora of meat and bone raw materials is determined, sanitary and hygienic and technological directions for reducing the development of microorganisms and the necessary conditions for their intoxication are proposed. The importance of maintaining conditions for reducing the criterion operational development and saturation of meat and bone raw materials with pathogenic and opportunistic microorganisms during their production and processing has been established. It is assessed based on the saturation of the meat itself with microorganisms during the stages of its production and processing, as well as the contamination of the environment. Sanitary and hygienic and inactivation measures and means for reducing the contamination of meat and bone raw materials during processing and production of packaged meat and bone broths of long shelf life with the exclusion of active interaction of the processed meat and bone raw materials with the environment by using bactericidal ultraviolet irradiation during preparatory operations and during subsequent operations, using continuous flow-shop technology in a closed environment closed from external influences are proposed.

  • Open Access

    Optimal parameters of processing wheat grain in an ultrasonic installation

    by N L Morgunova, F Y Rudik, O S Fomenko, Z I Ivanova, D V Makarov, E A Sundukov

    The article deals with the issues related to the process of grain processing to accelerate the process of wetting during simple grinding into wallpaper flour and decontamination of grain during storage with ultrasonic intensification of the process. A mathematical simulation of the grain processing process was carried out using the Statistica.10 program. The optimal operating parameters of the preparation of wheat grain for simple grinding were selected: water temperature – 300C, processing time – 40 seconds, the frequency of ultrasonic vibrations – 18-18.2 kHz, the intensity of the ultrasonic field – no more than 1 W/cm2.


  • Open Access

    Experimental Determination of the Influence of the Peeling Machine Constructive and Operating Parameters on the Criteria of the Peeling Process Efficiency

    by Alexander V. Anisimov, Feliks Ya. Rudik

    The determination of the optimal technological efficiency of the peeling process, in terms of the number of detached casings and unit costs of the process, is an important task. The purpose of the study is to give reasons for a comprehensive evaluation criterion of the technological efficiency of peeling wheat grain and choose the optimal values of the parameters of grain peeling, taking into account the energy intensity of the process.

  • Open Access

    Improving the Efficiency of Grinding Sugar Beet in Centrifugal Beet Cutters

    by Feliks Ya. Rudik, Sergey А. Bogatyrev, Anatoliy P. Kovylin, Madina S. Tulieva

    Introduction. Grinding sugar beet should be carried out with minimal losses in centrifugal beet cutters with specially designed knives that provide frequent and constant chaotic longitudinal-lateral cutting of circular conductive beet knots. The objective of the work is to increase the reliability of the knives of centrifugal beet cutters by structural and technological strengthening in the process of their production and restoration. Materials and Methods. The state of the cutting edges of the knives was determined by using the micrometric measurement of the wear and deformation of the edges. Physical and mechanical indicators were analyzed based on the values of wear resistance, microhardness, and bending endurance. Results. The analyzes of the defective state of the knives of centrifugal beet cutters and theoretical studies of the grinding process have allowed formulating the factors affecting the permeability of the beet chips and the efficiency of their grinding with knives of a special diamond-shaped design. Experimental studies have made it possible to establish dynamically substantiated design parameters of an improved knurled knife. Discussion and Conclusion. The proposed measures ensured an increase in the durability of knives by 27-30%, the relative wear resistance of cutting edges by 20%, the limit of endurance of cutting edges for bending by 25% and a shift increase in the length of chips by 18-20% with an increase in its permeability by 16-18%.

  • Open Access

    Results of Theoretical Definition of Structural and Kinematic Parameters of Peeling Machine Working Elements

    by Alexander V. Anisimov, Feliks Ya. Rudik

    Introduction. Peeling the moistened grains before grinding allows removing most of the outer shells with impurities on them from the grain surface. At the present time, the most commonly used machines for peeling are devices operating on the principle of “compression and friction”, in which the grains move along the friction surfaces of the working bodies. The aim of this study is to define and select structural and kinematic parameters of the machine working bodies, which would most effectively perform the process of peeling, and to make energy assessment of grain peeling. Materials and Methods. To identify the dependence of the machine design and operating parameters on the inclination angle and punching angle of the sieve cylinder, a diagram of the movement of the grain along the inclined cylinder was drawn up using elements of the theory of the motion of material point on rough surfaces. The motion of grains on the cylinder surface is analyzed by the methods of analytical dynamics. Results. The values of the geometric parameters of the particle position at point A are expressed as a function of the cylinder inclination angle α and the angle characterizing the shape of the inclined line of stamping of the cylinder β. Energy assessment of grain peeling process was made. With the radius of the sieve cylinder R0 = 0.135 m, the width of the working annular gap к = 0.01 m, the length of the cylinder L = 0.4 m, the horizontal arrangement of the cylinder, the angular velocity of the shaft ω = 90 rad/s, the angle of inclination of the stamping β = 22º, the calculated power was P = 4.5 kW. Discussion and Conclusion. As a result of analyzing the motion trajectory of the grain located on the cylinder surface, there have been proposed the formulas relating the shape of the inclined punching line of the cylinder, characterized by the angle β, to the inclination angle α, the radius R0 of the cylinder, the shaft angular velocity and the grain frictional properties. The obtained analytical dependencies can be used for the approximate definition of the peeling machine design and kinematic parameters.


  • Open Access

    Технология и средство механизации для обработки зерна

    by Феликс Яковлевич Рудик, Наталья Львовна Моргунова, Екатерина Сергеевна Красникова, Елена Александровна Фауст, Никита Александрович Семилет

    Зерно подвержено заражению плесневыми грибами, что является значительной проблемой в кормопроизводстве и пищевой промышленности. Высокая концентрация микотоксинов в зерне может привести к отравлениям и даже летальному исходу. Поэтому актуальны исследования по совершенствованию технологий и технических средств обеззараживания зерна. В статье представлены результаты исследований бактерицидного свойства ультразвука низких частот в среде анолита. Авторами разработана технология и установка для обработки зерна. Показана целесообразность проведения обеззараживания зерна ультразвуком низких частот 24-26 кГц с интенсивностью ультразвука не более 1 Вт/см2 в среде анолита, полученного на установке СТЭЛ. Разработанная технология позволяет уменьшить содержание в зерне бактерий и плесневых грибов, а также предотвращает накопление в нём микотоксинов и уменьшает загрязненность минеральными примесями.


  • Open Access

    Decontamination of grain by ultrasound

    by F Ya Rudik, N L Morgunova, E S Krasnikova

    The article considers the method of grain processing in the medium of an anolyte, produced at the STEL type plant, with subsequent washing and drying to a humidity of not more than 14%. Decontamination of grain was carried out by ultrasound of low frequencies 24-26 kHz with ultrasound intensity no more than 1 W/cm2. The method provides a reduction in the content of mold fungi in the grain, prevents the development of mycotoxins in it, reduces contamination with mineral impurities and insect pest.


  • Open Access

    The Experimental Determination of Optimum Parameters of the Equipment for Processing Grain in Preparation for Grinding

    by Alexander V. Anisimov, Felix Ya. Rudik

    Introduction. Modern technology of grain processing pays special attention to the qualitative and efficient preparation of grain for milling. At small enterprises with a reduced technological process, this is almost the only way to improve product yield and quality. Without proper multi-stage preparation of grain for milling at small enterprises, it is impossible to achieve the required quality and quantity of products produced by industrial mills. Grain peeling is one of the most effective ways to clean the surface from dirt and remove outer shells. The removal of outer shells allows increasing the yield of high-grade flour at reduced milling diagrams. The efficiency of the peeling process is significantly infuencet by the design and operating parameters of the peeling machine. The purpose of this work is the experimental determination of optimal conditions for grain processing in the peeling and drying machine (the optimal combination of factors). Materials and Methods. To determine optimal conditions for grain processing in the peeling and drying machine, the method of extreme planning of the experiment was applied. The method of random balance was used to select the most significant factors based on their influence on the optimization parameter. The method of steep ascent on the response surface (the Box – Wilson method) was used to find the optimum area (the planning matrix was realized and statistical analysis of results and steep ascent on the response surface was carried out). Verification of the results was carried out on the software Statistica 10.0. Results. On the basis of experiments, a mathematical model of the technological process of wheat processing in the peeling and drying machine there were obtained, which linked the structural and mode parameters of the machine with the humidity of the treated grain. The results of the experiment confirmed the operability of the developed machine when working with high-humidity grain; they are fundamental for the machine’s further modernization. Discussion and Conclusion The analysis of the controlled factor dispersion diagram allowed us to select the most significant of them based on influence on the selected optimization parameter, the white flour color obtained from the treated grain. As a result of the evaluation of experimental data of the conducted studies, the design and mode parameters of the developed machine were determined, corresponding to the areas of the optimal optimization parameter: shaft rotation speed is 1400 rpm, angle of inclination of stamping on the sieve drum is 15 degrees, the initial moisture content of the processed grain is 15.50%, and the machine productivity does not exceed 700 kg/h.


  • Open Access

    Improving the Wear Resistance and Bending Strength of Knives Used in Centrifugal Beet Cutters

    by F. Ya. Rudik, S. A. Bredikhin

    The efficiency of sugar production depends largely on the state of beet chips obtained from a centrifugal sugar beet cutter. It is shown that a one-shift operation of defective knives may result in a loss of up to 28-30 percent of sucrose. (Research purpose) To establish quality indicators of beet chips obtained from a centrifugal beet cutter, to improve a design and production technology of knives with increased physical and mechanical characteristics. (Materials and methods) The authors identified the reasons leading to the deterioration of the knife parameters and ensuring the quality of sugar beet cutting. To increase the indicators of wear resistance and bending strength of the cutting edges, the knife design was modified and a new technology of knife manufacturing was offered. The authors theoretically and experimentally proved the feasibility of replacing the manufacturing technology of the cutting edges of knives - from cutting to plastic deformation in die tooling. (Results and discussion) The authors have determined the mechanism and consequences of the wear and breakage of cutting points and the deformation and breakage of cutting edges of sugar beet knives. The technology of edge die stamping with special equipment was offered. The design of tooling for die stamping and machining of knife’s cutting edges was developed and experimentally tested in production conditions. (Conclusions) The authors offered the methods of strengthening cutting edges of knives with die casting, as well as offered solutions to the design problems of knife manufacturing using special high-performance and resource-saving equipment. The main physical and mechanical characteristics of sugar beet knives manufactured according to conventional and improved technologies have been experimentally determined and tested under operating conditions. The authors show the advantages of the cutting edges of sugar beet knives manufactured according to the improved technology; the study has proved an increase in microhardness by 14 percent and an increase in bending strength by 30 percent.