Wenyang Wang
Research Subjects
Wenyang Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hongwei Zhao
Jilin University
2 shared publications Ye Hu
Key Laboratory of CNC Equipment Reliability Ministry of Education 5988 RenMin Street Changchun 130025 China
2 shared publicationsDan Zhao
School of Mechanical and Aerospace Engineering Jilin University 130025 Changchun China
1 shared publication- Lixia Xu
Key Laboratory of CNC Equipment Reliability, Ministry of Education, and the School of Mechanical and Aerospace Engineering, Jilin University, Changchun, China
1 shared publication Tong Wu
School of Mechanical and Aerospace Engineering Jilin University 130025 Changchun China
1 shared publication- Zhaoxin Wang
School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication
Latest Publications
- 1 August 2020
- Published by Wiley in Steel Research International
- Vol. 91 (10)
Dissimilar Friction Stir Welding of Austenitic and Duplex Stainless Steel: Effect of Material Position and Tool Offset
Dissimilar friction stir welding (FSW) of 2205 duplex stainless steel (2205 DSS) and 304 austenitic stainless steel (304 ASS) is carried out with various parameters. The effect of material position and tool offset on material flow and mixing, the microstructure, and the mechanical properties of joints are investigated, and the relationship between tool torque and material flow is determined. With tool offset to retreating side (RS), defect‐free joints with proper material mixing are fabricated. When 304 ASS is placed on the advancing side (AS), the material mixing is better than is the case with the opposite material position, but results in a larger stirring zone (SZ) width. A large amount of mixed zone (MXZ) with a different phase ratio (γ–α) from both base metals (BMs) is formed in the defect‐free joints due to the alloying element diffusion between the two steels and severe plastic deformation. Due to the dynamic recrystallization, the SZ of all joints has higher hardness than 304 BM. The defect‐free dissimilar joints have higher tensile strength than 304 BM and good ductility.
- 1 August 2020
- Published by Wiley in Steel Research International
- Vol. 91 (10)
Dissimilar Friction Stir Welding of Austenitic and Duplex Stainless Steel: Effect of Material Position and Tool Offset
Dissimilar friction stir welding (FSW) of 2205 duplex stainless steel (2205 DSS) and 304 austenitic stainless steel (304 ASS) is carried out with various parameters. The effect of material position and tool offset on material flow and mixing, the microstructure, and the mechanical properties of joints are investigated, and the relationship between tool torque and material flow is determined. With tool offset to retreating side (RS), defect‐free joints with proper material mixing are fabricated. When 304 ASS is placed on the advancing side (AS), the material mixing is better than is the case with the opposite material position, but results in a larger stirring zone (SZ) width. A large amount of mixed zone (MXZ) with a different phase ratio (γ–α) from both base metals (BMs) is formed in the defect‐free joints due to the alloying element diffusion between the two steels and severe plastic deformation. Due to the dynamic recrystallization, the SZ of all joints has higher hardness than 304 BM. The defect‐free dissimilar joints have higher tensile strength than 304 BM and good ductility.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2020 (1)
Effect of Rotation Speed on Microstructure and Mechanical Properties of Friction‐Stir‐Welded 2205 Duplex Stainless Steel
In the present study, 1.86‐mm‐thick steel plates (UNS S32205) were friction‐stir‐welded at various rotation speeds of 300 to 600 rpm and a constant welding speed of 100 mm·min−1. The effect of rotation speed on the microstructure and mechanical properties of the welds was researched. The welding temperature was recorded during friction stir welding (FSW), and the microstructure and mechanical properties of the welds were assessed. The incomplete penetration defect was formed at 300 rpm due to the insufficient heat input, and macroscopic groove‐like defect was formed at 600 rpm because of the serious sticking of tool. Defect‐free welds were obtained at 350 to 500 rpm. The lower rotation speed corresponds to lower heat input during FSW, which resulted in finer recrystallized grains within the stirred zone and thermomechanically affected zone. The joint width was increased with the increasing rotation speed. Therefore, both the strength and hardness of the weld joints increased with the decreasing of rotation speed.
- 1 January 2020
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2020 (1)
Open AccessEffect of Rotation Speed on Microstructure and Mechanical Properties of Friction‐Stir‐Welded 2205 Duplex Stainless Steel
In the present study, 1.86‐mm‐thick steel plates (UNS S32205) were friction‐stir‐welded at various rotation speeds of 300 to 600 rpm and a constant welding speed of 100 mm·min−1. The effect of rotation speed on the microstructure and mechanical properties of the welds was researched. The welding temperature was recorded during friction stir welding (FSW), and the microstructure and mechanical properties of the welds were assessed. The incomplete penetration defect was formed at 300 rpm due to the insufficient heat input, and macroscopic groove‐like defect was formed at 600 rpm because of the serious sticking of tool. Defect‐free welds were obtained at 350 to 500 rpm. The lower rotation speed corresponds to lower heat input during FSW, which resulted in finer recrystallized grains within the stirred zone and thermomechanically affected zone. The joint width was increased with the increasing rotation speed. Therefore, both the strength and hardness of the weld joints increased with the decreasing of rotation speed.