MAManoel Luis Aguiar

Manoel Luis Aguiar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Manoel Luis Aguiar has a total of 82 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Duty Cycle Based Model Predictive Control With Hexagonal Virtual Voltage Vectors for Grid-Tied Generation System With the Six-Switch Converter

    by Paulo Roberto Ubaldo Guazzelli, Stefan Thiago Cury Alves dos Santos, José Roberto Boffino de Almeida Monteiro, Manoel Luís de Aguiar

    The application of duty cycle based Finite Control Set Model Predictive Control (FCS-MPC) to the Six-Switch Converter (SSC), a reduced switch count multiport converter, faces the drawback of an asymmetrical and limited set of voltage vectors, which deteriorates the quality of the system currents. To overcome this issue, this paper proposes an FCS-MPC technique with duty cycle optimization for a wind energy system comprised of SSC, induction generator, and grid connection, for variable speed applications. The main contribution of the technique is the use of a hexagonal set of virtual voltage vectors. Analysis of the experimental results verifies how the proposed technique reduced the grid current THD by over 60% when compared to the equivalent duty cycle based FCS-MPC without the hexagonal voltage vectors. Additionally, the machine torque ripple factor and the grid active power ripple factors were also reduced. As a result, the proposed control technique boosts the application of the SSC in renewable household wind energy systems.


  • Model Predictive Control With Duty Cycle Optimization and Virtual Null Vector for Induction Generator With Six Switch Converter

    by Paulo Roberto Ubaldo Guazzelli, Stefan Thiago Cury Alves dos Santos, José Roberto Boffino de Almeida Monteiro, Manoel Luís de Aguiar

    The incorporation of duty cycle optimization in the finite control set model predictive control increased its advantages, improving its steady-state performance and maintaining its fast dynamics. However, duty cycle optimization depends on the application of a null vector alongside the optimal vector, and some converters do not have a null voltage vector inherently. This is the case of the six-switch converter, a reduced switch count converter which replaces the back-to-back converter with only 50% of the number of switches, and whose union with predictive control has been little exploited. This paper develops a model predictive control with duty cycle optimization for a variable speed turbine wind power system with the six switch converter connected to grid and to an squirrel cage induction generator. Calculations are performed by the means of a virtual null voltage vector properly applied to the system. Experimental results show the proposed control technique improved steady-state performance of the system, with lower torque ripples, active power ripples and current total harmonic distortion, certifying the controller as a feasible technique for the application.


  • Decoupled Predictive Current Control With Duty-Cycle Optimization of a Grid-Tied Nine-Switch Converter Applied to an Induction Generator

    by Paulo Roberto Ubaldo Guazzelli, Stefan Thiago Cury Alves dos Santos, Allan Gregori de Castro, William Cesar de Andrade Pereira, Carlos Matheus Rodrigues de Oliveira, Jose Roberto Boffino de Almeida Monteiro, Manoel Luis de Aguiar

    The nine-switch converter (NSC) was developed aiming at the reduction in the number of power converter switches in multiport systems, such as variable-speed drives for power generation. Among the possible control techniques for the NSC, finite-control-set model-predictive control (FCS-MPC) stands out due to its fast dynamics and easy incorporation of system restrictions. However, converters with many switching possibilities and control goals increase the computational burden and the cost function complexity. Moreover, FCS-MPC can present high ripple values in the system outputs. This article proposes a decoupled predictive current control with duty-cycle optimization (PCC-DD) for the NSC, which decouples the control of an induction generator from the grid control. The separation between grid and generator controls decreases the enumeration of voltage vectors to be performed, reducing computational burden. Then, duty-cycle calculations are responsible for reducing torque and active power ripples. Experimental results show that PCC-DD provides lower ripple factors for the desired variables when compared to the approach with a concentrated cost function. The main contribution is a better steady-state performance with a lower computational burden. Therefore, PCC-DD is a suitable low-ripple technique for NSC control and for application to power generation with variable-speed generators.


  • Proportional Wavelet Sliding Mode Controller for Torque Ripple Reduction in BLDC Motor

    by Mateus Moro Lumertz, Carlos Matheus R. de Oliveira, Allan Gregori de Castro, Paulo Roberto U. Guazzelli, Manuel Luis de Aguiar, Jose Roberto B. A. Monteiro

    Permanent magnetic synchronous machines with trapezoidal back-electromotive force and six-step operation, also known as brushless direct current motors, have high torque undulations because needed current waveform can’t be provided. Proper vector control techniques used to reduce chattering, are high dependent on machine parameters and are complex to implement on real applications. Sliding Mode and Pseudo Sliding Mode are controllers with high dynamical performance and simple implementation, but increase torque undulations in machine control applications. On the other hand, wavelet multiresolution controllers have the feature of chattering reduction, but are complex to tune and analyze, due to the number of parallel detail and approximation coefficients used. This works proposes a simplified wavelet controller, replacing approximation coefficients with a proportional controller. This controller was used to design a proper sliding manifold for a sliding mode speed control, on a BLDC motor, without using machine parameters. A genetic algorithm was used to determine an optimum mother wavelet for a fixed decomposition level, leaving just one parameter to tune in future works. In results, an improvement to the proposed controller was suggested, for a controller with high dynamical and steady state performance, without torque undulations and easier to tune than wavelet multiresolution controllers.


  • Finite Control Set Model Based Predictive Control of Grid-Tied Six-Switch Converter Applied to Induction Generator

    by Paulo R. U. Guazzelli, Allan G. de Castro, Stefan T. C. A. dos Santos, Carlos M. R. de Oliveira, Jose R. B. A. Monteiro, Manoel L. de Aguiar

    Finite Control Set Model Based Predictive Control (FCS-MPC) established itself as an effective technique for the control of power electronic converters, with fast dynamics and the absence of voltage modulators. However, there are still converters in the literature which did not exploit the advantages of FCS-MPC, as the Six-Switch Converter (SSC), a multiport converter which can replace the back-to-back converter in power generation with 50% of the switch count. As a result, this paper investigates the use of FCS-MPC in the SSC for grid-tied power generation with the squirrel-cage induction generator. Two Predictive Current Control (PCC) approaches are presented: a Concentrated PCC (PCC-C), in which a centralized cost function is employed for control decision evaluation; and a Decoupled PCC (PCC-D), with independent cost functions for the grid and generator control. Simulation results show PCC-D provided better torque ripple factor and better grid current distortion, when compared to the concentrated approach. Also, PCC-D eliminated the diverging bus capacitor voltage offset of PCC-C, and the superior performance was obtained with a lower computational cost.


  • High-Accuracy Dynamic Load Emulation Method for Electrical Drives

    by Carlos Matheus Rodrigues de Oliveira, Manoel Luis de Aguiar, Allan Gregori de Castro, Paulo Roberto Ubaldo Guazzelli, William Cesar de Andrade Pereira, Jose Roberto Boffino de Almeida Monteiro

    This paper addresses the problem of dynamic load emulation (DLE) with high accuracy of any mechanical load for which the mathematical model is known. The control strategy of a load machine is used to design tasks of control algorithms of variable speed and torque drives for educational purposes and several engineering applications, as transportation and renewable energy. The structure uses a set-point feed-forward compensator with speed-tracking controller which provides robustness under parametric variation and non-modeled dynamics. Nonlinear effects and constraints of the experimental setup shaft can be included in the compensator, which makes the strategy an alternative method for systems operating under different degrees of uncertainty. Moreover, different control approaches can be applied to both compensator and speed controller. The method can be applied with any rotary machines, where two induction motors (IMs) with directly coupling are adopted. The method was compared to two other DLE methods and was validated through nonlinear models whose inertia and friction are not constant. The simulated and experimental results were very similar, even when high uncertainty was assumed.


  • Virtual Platform of Field Oriented Control of Induction Motor to Assist in Education of Undergraduate Students

    by G. H. Bazan, M. F. Castoldi, A. Goedtel, W. C. A. Pereira, M. L. Aguiar

    This paper proposes a virtual teaching platform applied to undergraduate students concerning an induction motor drive technique. Such a technique is called as Field Oriented Control (FOC) and it is presented and analyzed, in a simple form, by using the proposed platform. This virtual platform uses a GUIDE tool from MATLAB jointly with the SIMULINK. Simulation results of FOC strategy and also its simplicity usage are shown in this work.


  • Analysis of the Dynamic Emulation Problem for Validation of Position Control Algorithms in Machine Drives

    by Carlos M. R. de Oliveira, Manoel Luis de Aguiar, Paulo R. U. Guazzelli, Allan Gregori de Castro, Stefan T. C. A. dos Santos, Jose R. B. A. Monteiro

    Load emulation is an important stage in the development of high performance of control algorithms, which allow experimental tests in controlled environments. This work investigates the validation problem in position control algorithms of electric motors with two coupled motors. Two approaches commonly used in the literature are explored seeking high fidelity in the mechanical dynamic behavior. The first one is the open-loop torque control, which uses a torque reference directly provided by the emulation model, and the second one is a closed loop position control. Simulated and experimental results demonstrate that the exact emulation does not exist for both approaches. Therefore, the research of new control topologies is important/interesting for proper load emulation.


  • Dual Predictive Current Control of Grid Connected Nine-Switch Converter Applied to Induction Generator

    by Paulo R. U. Guazzelli, Allan G. de Castro, Stefan T. C. A. dos Santos, Carlos M.R. de Oliveira, William C. A. Pereira, Jose R. B. A. Monteiro, Manoel L. de Aguiar

    Finite Control Set Model Predictive Control appears as a powerful tool for the control of power electronic converters, allowing fast dynamics without the use of voltage modulators. However, converters with many switching possibilities and control goals increase the computational burden and the cost function complexity. This paper proposes a dual Predictive Current Control (PCC-D) for the Nine-Switch Converter (NSC), which decouples the induction generator control from the grid control. Two controllers act alternately and independently. Simulation results show that the PCC-D provided a better grid voltage and current distortion, when compared to the one-vector approach. The main contribution relies on an enumeration of lesser vectors, reducing the computational burden of PCC. Therefore, PCC-D appears as a suitable alternative for NSC control and its application to power generation with variable speed generators.