Francesco Delloro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Francesco Delloro has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Alain Thorel
MINES ParisTech, PSL Research University, MAT – Centre des matériaux, CNRS UMR 7633, BP 87, 91003 Evry, France
1 shared publication- Anne-Françoise Gourgues-Lorenzon
Mines Paris, PSL Research University, Centre des Matériaux, UMR CNRS 7633
1 shared publication François Lavaud
TOYAL EUROPE, Route de Lescun F-64490 Accous, France
1 shared publication- François Willot
Centre de Morphologie Mathématique
1 shared publication - Gilles Rolland
IMSIA/UMR EDF/CNRS/CEA/ENSTA, EDF R &D, Palaiseau, France
1 shared publication Hugo Durand
MINES ParisTech, PSL Research University, MAT – Centre des matériaux, CNRS UMR 7633, BP 87, 91003 Evry, France
1 shared publication
Latest Publications
- 22 August 2022
- Published by Springer Nature
- p. 349-355
Quantitative Characterization of Ductility for Fractographic Analysis
- 22 August 2022
- Published by Springer Nature
- p. 349-355
Quantitative Characterization of Ductility for Fractographic Analysis
- Open Access
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 01036
Characterization of mechanical behaviour of aluminum powders under fast dynamic conditions
Cold spray is a process belonging to the thermal spray family, characterized by relatively low temperatures and high particle velocities. Upon impact, particles undergo large plastic deformation at solid state in dynamic regime up to 109 s-1. The knowledge of powder behaviour in such conditions is essential to catch key phenomena in cold spray and a necessary step for a correct process modelling. However, little is known on mechanical behaviour of feed-stock powders when submitted to cold spray conditions. In this study, an approach focused on single particles combining laser shock induced impact, namely LASHPOL (LAser SHock POwder Launcher), and quasi-static compression was therefore developed. This method was applied in this study on spherical Aluminium powders but can work with any other powder material. The mechanical behaviour of powders was characterized and used to fit the parameters of Johnson-Cook constitutive model, by means of finite element inverse method. The combination of static and dynamic tests resulted in an original characterization of powder, which revealed having a different mechanical behaviour than the corresponding bulk material.
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 01036
Open AccessCharacterization of mechanical behaviour of aluminum powders under fast dynamic conditions
Cold spray is a process belonging to the thermal spray family, characterized by relatively low temperatures and high particle velocities. Upon impact, particles undergo large plastic deformation at solid state in dynamic regime up to 109 s-1. The knowledge of powder behaviour in such conditions is essential to catch key phenomena in cold spray and a necessary step for a correct process modelling. However, little is known on mechanical behaviour of feed-stock powders when submitted to cold spray conditions. In this study, an approach focused on single particles combining laser shock induced impact, namely LASHPOL (LAser SHock POwder Launcher), and quasi-static compression was therefore developed. This method was applied in this study on spherical Aluminium powders but can work with any other powder material. The mechanical behaviour of powders was characterized and used to fit the parameters of Johnson-Cook constitutive model, by means of finite element inverse method. The combination of static and dynamic tests resulted in an original characterization of powder, which revealed having a different mechanical behaviour than the corresponding bulk material.
- 13 May 2020
- Published by Springer Nature
- p. 129-175
Advanced Modeling and Simulation Tools to Address Build-Up Issues in Additive Manufacturing by Cold Spray
- 13 May 2020
- Published by Springer Nature
- p. 129-175
Advanced Modeling and Simulation Tools to Address Build-Up Issues in Additive Manufacturing by Cold Spray