Guosong Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guosong Zeng has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
Peng Gao
5 shared publicationsZhenghao Wei
4 shared publications- Chee-Keong Tan
College of Integrated Circuit Science and Engineering, Nanjing University of Posts and Telecommunications 1 , Nanjing 210023
3 shared publications Haifeng Gao
3 shared publicationsHuiqiang Liang
3 shared publications- Jiahe Cao
Advanced Materials Thrust, Function Hub, The Hong Kong University of Science and Technology (Guangzhou) 2 , Guangzhou 511453, Guangdong
3 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 10 (3)
Taming the boundary effect: Femtosecond laser slicing of 4H-SiC enabled by side scribing for improved processability
The 4H polytype of silicon carbide (4H-SiC) has excellent properties such as high electron mobility and high saturation electron velocity; it has therefore become an important material for high-power and high-frequency devices. In the slicing step of wafer fabrication, however, conventional wire-saw cutting is constrained by the inherent high hardness and brittleness of 4H-SiC, causing excessive material removal and surface and subsurface damage. To overcome these limitations, this study proposes a femtosecond laser slicing technology combined with side scribing. A simulation model of the boundary effect in internal laser processing was established to analyze the optical energy distribution under spherical aberration. The simulations revealed boundary regions that resist laser modification because of the coupling between asymmetric focusing and spherical aberration, which degrades the slicing quality of conventional laser processing. Systematic parametric experiments were then used to investigate the influence of the laser processing parameters on the formation of the modified layer. Targeted experiments performed using the optimized processing parameters provided a quantitative characterization of the hard-to-modify regions and guided the application of the side-scribing process. The peeling results demonstrate that the proposed side-scribing-assisted femtosecond laser slicing process effectively reduces the peeling stress and the cracking that occurs during slicing, achieving a 68% reduction in peeling stress and a 27% reduction in the arithmetic mean roughness Sa of the peeled surface, together with the formation of laser-induced periodic surface structures that are better suited to subsequent processing, compared with conventional laser slicing. This study improves the processability of 4H-SiC wafer slicing and provides a new approach to substrate preparation for wide-bandgap semiconductor materials.
- 1 September 2026
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 10 (3)
Open AccessTaming the boundary effect: Femtosecond laser slicing of 4H-SiC enabled by side scribing for improved processability
The 4H polytype of silicon carbide (4H-SiC) has excellent properties such as high electron mobility and high saturation electron velocity; it has therefore become an important material for high-power and high-frequency devices. In the slicing step of wafer fabrication, however, conventional wire-saw cutting is constrained by the inherent high hardness and brittleness of 4H-SiC, causing excessive material removal and surface and subsurface damage. To overcome these limitations, this study proposes a femtosecond laser slicing technology combined with side scribing. A simulation model of the boundary effect in internal laser processing was established to analyze the optical energy distribution under spherical aberration. The simulations revealed boundary regions that resist laser modification because of the coupling between asymmetric focusing and spherical aberration, which degrades the slicing quality of conventional laser processing. Systematic parametric experiments were then used to investigate the influence of the laser processing parameters on the formation of the modified layer. Targeted experiments performed using the optimized processing parameters provided a quantitative characterization of the hard-to-modify regions and guided the application of the side-scribing process. The peeling results demonstrate that the proposed side-scribing-assisted femtosecond laser slicing process effectively reduces the peeling stress and the cracking that occurs during slicing, achieving a 68% reduction in peeling stress and a 27% reduction in the arithmetic mean roughness Sa of the peeled surface, together with the formation of laser-induced periodic surface structures that are better suited to subsequent processing, compared with conventional laser slicing. This study improves the processability of 4H-SiC wafer slicing and provides a new approach to substrate preparation for wide-bandgap semiconductor materials.
- 22 August 2026
- Published by Elsevier in Applied Surface Science
- Vol. 752
Unveiling the effects of anions on photoelectrochemical etching of gallium nitride
- 22 August 2026
- Published by Elsevier in Applied Surface Science
- Vol. 752
Unveiling the effects of anions on photoelectrochemical etching of gallium nitride
- Open Access
- 22 July 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Visualization of oxophilic regulation for alkaline hydrogen evolution on Ni-based electrocatalyst via multimodal operando approaches
Alkaline hydrogen evolution reaction holds immense promise for sustainable energy conversion due to its inherent compatibility with earth-abundant electrocatalysts and potential for large-scale, high-purity hydrogen production. However, sluggish kinetics remain a formidable bottleneck for its industrial deployment. Although incorporating oxophilic components is widely used to promote water activation, the catalytic role of oxygen-affinity-related sites is often interpreted statically, without considering dynamic evolution of local coordination under operating conditions. Here, we synthesize a crystalline-amorphous Ni/TiO2 heterojunction via a grain-boundary segregation strategy and combine multi-modal operando techniques to directly visualize reversible, bias-induced reconstruction of the oxophilic component. These observations provide direct evidence that, at the Ni/TiO2 interface, oxygen affinity is a tunable parameter encoded by nanoscale coordination and interfacial chemistry, and elucidate how its modulation governs water dissociation and hydroxyl handling. We demonstrate that the resulting four-coordinated Ti sites serve as highly efficient centers for water dissociation and hydroxyl adsorption, thereby synergistically optimizing the hydrogen adsorption/desorption energetics. This work offers a mechanistic and methodological basis for rational nano-heterointerfaces engineering in advanced electrocatalysts.
- 22 July 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessVisualization of oxophilic regulation for alkaline hydrogen evolution on Ni-based electrocatalyst via multimodal operando approaches
Alkaline hydrogen evolution reaction holds immense promise for sustainable energy conversion due to its inherent compatibility with earth-abundant electrocatalysts and potential for large-scale, high-purity hydrogen production. However, sluggish kinetics remain a formidable bottleneck for its industrial deployment. Although incorporating oxophilic components is widely used to promote water activation, the catalytic role of oxygen-affinity-related sites is often interpreted statically, without considering dynamic evolution of local coordination under operating conditions. Here, we synthesize a crystalline-amorphous Ni/TiO2 heterojunction via a grain-boundary segregation strategy and combine multi-modal operando techniques to directly visualize reversible, bias-induced reconstruction of the oxophilic component. These observations provide direct evidence that, at the Ni/TiO2 interface, oxygen affinity is a tunable parameter encoded by nanoscale coordination and interfacial chemistry, and elucidate how its modulation governs water dissociation and hydroxyl handling. We demonstrate that the resulting four-coordinated Ti sites serve as highly efficient centers for water dissociation and hydroxyl adsorption, thereby synergistically optimizing the hydrogen adsorption/desorption energetics. This work offers a mechanistic and methodological basis for rational nano-heterointerfaces engineering in advanced electrocatalysts.
- Open Access
- 20 April 2026
- Published by Springer Nature in Nanomanufacturing and Metrology
- Vol. 9 (1) , 14
Tribological Behavior of β-Ga2O3 Under Oxidative Aqueous Environment
- 20 April 2026
- Published by Springer Nature in Nanomanufacturing and Metrology
- Vol. 9 (1) , 14
Open AccessTribological Behavior of β-Ga2O3 Under Oxidative Aqueous Environment
- Open Access
- 23 March 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (12)
Tunable electronic properties of κ-(Al, In)2O3/Ga2O3 digital alloys via superlattice design
κ-Ga2O3-based digital-alloy superlattices offer a promising alternative to traditional random alloys for high performance heterostructure devices. Using density functional theory, we model (Al2O3/κ-Ga2O3) and (In2O3/κ-Ga2O3) superlattices with varying monolayer (ML) thicknesses (1 ML/3 ML, 2 ML/2 ML, and 3 ML/1 ML). Our calculations reveal precise tuning of lattice parameters and bandgaps dependent on layer thickness. The incorporation of Al2O3 introduces tensile strain and widens bandgap up to 6.65 eV, while In2O3-rich structures exhibit compressive strain with bandgap reduction down to 3.32 eV. Element-projected band structures confirm quantum confinement effects and interfacial contributions to electronic states. Notably, intersubband transition energies are controllable via ML thickness, enabling absorption in the telecom-compatible wavelength range (∼1.55 μm). Band alignment analysis reveals significant conduction band offsets (up to 3.71 eV for Al2O3/Ga2O3), which is vital for polarization-induced 2DEG (two-dimensional electron gas) formation. This work demonstrates the feasibility of κ-Ga2O3 digital-alloy superlattices for tailored high-electron-mobility transistors and quantum-well infrared photodetectors.
- 23 March 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (12)
Open AccessTunable electronic properties of κ-(Al, In)2O3/Ga2O3 digital alloys via superlattice design
κ-Ga2O3-based digital-alloy superlattices offer a promising alternative to traditional random alloys for high performance heterostructure devices. Using density functional theory, we model (Al2O3/κ-Ga2O3) and (In2O3/κ-Ga2O3) superlattices with varying monolayer (ML) thicknesses (1 ML/3 ML, 2 ML/2 ML, and 3 ML/1 ML). Our calculations reveal precise tuning of lattice parameters and bandgaps dependent on layer thickness. The incorporation of Al2O3 introduces tensile strain and widens bandgap up to 6.65 eV, while In2O3-rich structures exhibit compressive strain with bandgap reduction down to 3.32 eV. Element-projected band structures confirm quantum confinement effects and interfacial contributions to electronic states. Notably, intersubband transition energies are controllable via ML thickness, enabling absorption in the telecom-compatible wavelength range (∼1.55 μm). Band alignment analysis reveals significant conduction band offsets (up to 3.71 eV for Al2O3/Ga2O3), which is vital for polarization-induced 2DEG (two-dimensional electron gas) formation. This work demonstrates the feasibility of κ-Ga2O3 digital-alloy superlattices for tailored high-electron-mobility transistors and quantum-well infrared photodetectors.
- 23 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (12)
Atomic-level revelation of spontaneous polarization orientation and piezoelectricity in ε -Ga2O3
Advancing polarization control in semiconductors is pivotal for next-generation electronics, enabling revolutionary advances in energy and industrial systems. The metastable ε-Ga2O3 holds promise for polarization-engineered devices but remains hindered by unresolved polarization orientation and ambiguous piezoelectric responses. Here, using an integrated experimental and theoretical approach, we demonstrate that ε-Ga2O3 exhibits a spontaneous polarization (Psp) of −24.8 μC/cm2 oriented antiparallel to the crystal growth direction. The piezoelectric coefficient d33 was experimentally measured as 4.125 pm/V, in strong agreement with the theoretical value of 4.93 pm/V. The phase-pure ε-Ga2O3 films were grown via low-pressure mist-CVD with exceptional crystallinity, as evidenced by an x-ray diffractometer rocking curve [full-width-at-half-maximum (FWHM) = 0.08°]. Optimized piezoelectric force microscopy protocols were employed to determine d33, while the orientation of Psp was resolved using pulsed DC bias-dependent amplitude/phase-voltage measurements combined with aberration-corrected scanning transmission electron microscopy. This multimodal methodology enabled direct mapping of bound charge distributions at the film surface and provided atomic-scale visualization of crystal orientation. These findings clarify ε-Ga2O3 polarization ambiguities, establish structure–property relationships, and unlock transformative potential for advancing power electronics, high-frequency communication systems, and energy-efficient memory technologies.
- 23 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (12)
Atomic-level revelation of spontaneous polarization orientation and piezoelectricity in ε -Ga2O3
Advancing polarization control in semiconductors is pivotal for next-generation electronics, enabling revolutionary advances in energy and industrial systems. The metastable ε-Ga2O3 holds promise for polarization-engineered devices but remains hindered by unresolved polarization orientation and ambiguous piezoelectric responses. Here, using an integrated experimental and theoretical approach, we demonstrate that ε-Ga2O3 exhibits a spontaneous polarization (Psp) of −24.8 μC/cm2 oriented antiparallel to the crystal growth direction. The piezoelectric coefficient d33 was experimentally measured as 4.125 pm/V, in strong agreement with the theoretical value of 4.93 pm/V. The phase-pure ε-Ga2O3 films were grown via low-pressure mist-CVD with exceptional crystallinity, as evidenced by an x-ray diffractometer rocking curve [full-width-at-half-maximum (FWHM) = 0.08°]. Optimized piezoelectric force microscopy protocols were employed to determine d33, while the orientation of Psp was resolved using pulsed DC bias-dependent amplitude/phase-voltage measurements combined with aberration-corrected scanning transmission electron microscopy. This multimodal methodology enabled direct mapping of bound charge distributions at the film surface and provided atomic-scale visualization of crystal orientation. These findings clarify ε-Ga2O3 polarization ambiguities, establish structure–property relationships, and unlock transformative potential for advancing power electronics, high-frequency communication systems, and energy-efficient memory technologies.
- 1 February 2026
- Published by Tsinghua University Press in Friction
- Vol. 14 (2)
Investigation of the effect of humidity on the wear of cobalt metal
Cobalt-based alloys are widely used in aerospace and machinery due to their excellent mechanical properties, where extraordinary wear performance is also desirable to ensure stable operation. However, there is still scarce information on the tribological mechanism of the building block, the cobalt metal, especially under different humidity. The insight into the wear mechanism of Co under different humidity is crucial for the study of the tribological performance of Co-based alloys as well as exploring their potential applications under various working conditions. Here, we report the investigation of the humidity effect on the wear behavior of Co. The results showed that the Co exhibited an ultralow wear characteristic under the humid air environment (RH 70%) with the wear rate of 2.15 × 10-7 mm3/Nm and dramatically increased by three orders of magnitude to 1.47 × 10-4 mm3/Nm for dry ambient (~5% RH). Surface analysis revealed that the tribochemistry dominated the whole wearing process, with the worn surface almost fully covered by cobalt oxide, Co3O4, when subjected to the humid environment, whilst a small amount of oxide layers was only observed within the wear grooves under RH 5% testing condition. The stripe test results unraveled the evolution of this protective oxide generation, and the FIB/SEM of the cross-sections at different sliding stages bore out the role of tribochemistry for triggering such self-protection behavior. Our work provides a fundamental understanding of the wear mechanisms of Co metal, and we anticipate that this finding can offer valuable guidance for further improving the wear performance of cobalt-based alloys in the future.
- 1 February 2026
- Published by Tsinghua University Press in Friction
- Vol. 14 (2)
Investigation of the effect of humidity on the wear of cobalt metal
Cobalt-based alloys are widely used in aerospace and machinery due to their excellent mechanical properties, where extraordinary wear performance is also desirable to ensure stable operation. However, there is still scarce information on the tribological mechanism of the building block, the cobalt metal, especially under different humidity. The insight into the wear mechanism of Co under different humidity is crucial for the study of the tribological performance of Co-based alloys as well as exploring their potential applications under various working conditions. Here, we report the investigation of the humidity effect on the wear behavior of Co. The results showed that the Co exhibited an ultralow wear characteristic under the humid air environment (RH 70%) with the wear rate of 2.15 × 10-7 mm3/Nm and dramatically increased by three orders of magnitude to 1.47 × 10-4 mm3/Nm for dry ambient (~5% RH). Surface analysis revealed that the tribochemistry dominated the whole wearing process, with the worn surface almost fully covered by cobalt oxide, Co3O4, when subjected to the humid environment, whilst a small amount of oxide layers was only observed within the wear grooves under RH 5% testing condition. The stripe test results unraveled the evolution of this protective oxide generation, and the FIB/SEM of the cross-sections at different sliding stages bore out the role of tribochemistry for triggering such self-protection behavior. Our work provides a fundamental understanding of the wear mechanisms of Co metal, and we anticipate that this finding can offer valuable guidance for further improving the wear performance of cobalt-based alloys in the future.
- Open Access
Toughening beta-Ga2O3 via mechanically seeded dislocations
\b{eta}-Ga2O3 is a promising candidate for next-generation semiconductors, but is limited by its intrinsic brittleness, which hinders its application in flexible electronics and high-precision devices. This study explores a new approach to improving the damage tolerance of (001)-oriented \b{eta}-Ga2O3 by introducing mechanically seeded dislocations via surface scratching. By applying a Brinell indenter to scratch the surface along the [100] direction, we effectively generate edge-type dislocations belonging to the (011)[01-1] and/or (0-11)[011] slip systems within a mesoscale wear track. Through a combination of nanoindentation tests, surface morphology analysis, and microstructural characterization using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), we reveal that the introduction of dislocations significantly mitigates the formation of cleavage cracks during indentation, in contrast to that observed in as-received \b{eta}-Ga2O3. The mechanically seeded dislocations in the subsurface layers play an important role in preventing brittle fracture by facilitating stable plastic deformation.
Open AccessToughening beta-Ga2O3 via mechanically seeded dislocations
\b{eta}-Ga2O3 is a promising candidate for next-generation semiconductors, but is limited by its intrinsic brittleness, which hinders its application in flexible electronics and high-precision devices. This study explores a new approach to improving the damage tolerance of (001)-oriented \b{eta}-Ga2O3 by introducing mechanically seeded dislocations via surface scratching. By applying a Brinell indenter to scratch the surface along the [100] direction, we effectively generate edge-type dislocations belonging to the (011)[01-1] and/or (0-11)[011] slip systems within a mesoscale wear track. Through a combination of nanoindentation tests, surface morphology analysis, and microstructural characterization using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), we reveal that the introduction of dislocations significantly mitigates the formation of cleavage cracks during indentation, in contrast to that observed in as-received \b{eta}-Ga2O3. The mechanically seeded dislocations in the subsurface layers play an important role in preventing brittle fracture by facilitating stable plastic deformation.
- Open Access
- 20 March 2025
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 8 (3)
Investigation of the machinability of (001) single-crystal β-Ga2O3 via tribological methodology
Gallium oxide (Ga2O3) is a promising material for next-generation power devices due to its ultrawide bandgap and extremely high critical electric field strength; however, the strong anisotropy and cleavage tendency of Ga2O3 pose significant challenges for high-precision surface processing. In this work, a systematic study was conducted through tribological analysis of monocrystalline (001) β-Ga2O3. Initially, reciprocal sliding tests were conducted on β-Ga2O3 along different crystallographic directions, [100] and [010]. The results revealed that the [100] direction was more wear resistant, while the [010] direction was more prone to failure. Indentation experiments on (001) β-Ga2O3 showed extensive slip and cleavage cracking along different crystallographic orientations, indicating that mechanical wear might dominate the wear mode of this material. Subsequently, sliding tests under various environmental conditions revealed that the wear rate was correlated with humidity. Additionally, β-Ga2O3 exhibited time-dependent frictional behavior, with its coefficient of friction stabilizing around 0.1, 0.5, and 0.9 at different stages during the wear test. These findings indicate that the frictional behavior of Ga2O3 is closely linked to the state of its surface. This study provides critical insights into the tribological behavior of Ga2O3 and offers guidance for ultraprecision machining of this material.
- 20 March 2025
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 8 (3)
Open AccessInvestigation of the machinability of (001) single-crystal β-Ga2O3 via tribological methodology
Gallium oxide (Ga2O3) is a promising material for next-generation power devices due to its ultrawide bandgap and extremely high critical electric field strength; however, the strong anisotropy and cleavage tendency of Ga2O3 pose significant challenges for high-precision surface processing. In this work, a systematic study was conducted through tribological analysis of monocrystalline (001) β-Ga2O3. Initially, reciprocal sliding tests were conducted on β-Ga2O3 along different crystallographic directions, [100] and [010]. The results revealed that the [100] direction was more wear resistant, while the [010] direction was more prone to failure. Indentation experiments on (001) β-Ga2O3 showed extensive slip and cleavage cracking along different crystallographic orientations, indicating that mechanical wear might dominate the wear mode of this material. Subsequently, sliding tests under various environmental conditions revealed that the wear rate was correlated with humidity. Additionally, β-Ga2O3 exhibited time-dependent frictional behavior, with its coefficient of friction stabilizing around 0.1, 0.5, and 0.9 at different stages during the wear test. These findings indicate that the frictional behavior of Ga2O3 is closely linked to the state of its surface. This study provides critical insights into the tribological behavior of Ga2O3 and offers guidance for ultraprecision machining of this material.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (11)
Investigation on the structural and electronic property of monoclinic Al2O3/β-Ga2O3 superlattice with varying layer periods
In this study, we employ first-principles calculations to explore the structural and electronic properties of monoclinic Al2O3/Ga2O3 superlattices with varied layer thickness and to perform a comparative analysis with (AlxGa1−x)2O3 alloys. Our investigation examines the lattice constants and electronic energy bandgaps of both the superlattice structures and alloys across different Al concentrations, shedding light on the intricate relationship between composition and electronic properties. The analysis on electronic properties reveals that as the number of Al2O3 monolayers in the Al2O3/Ga2O3 superlattice rises from 2 to 6 monolayers, the bandgap correspondingly expands from 5.29 to 6.43 eV. The band alignment between monoclinic Al2O3 and Ga2O3 exhibits a type-II band alignment. The conduction and valence band offsets between the bulk material and Al2O3/Ga2O3 superlattice varies with change in the number of Al2O3 monolayers. Our study gives a deeper insight into the properties of the Al2O3/Ga2O3 superlattice and suggests a solution to the Al-phase separation issue in (AlxGa1−x)2O3 alloys for advanced semiconductor device applications.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (11)
Investigation on the structural and electronic property of monoclinic Al2O3/β-Ga2O3 superlattice with varying layer periods
In this study, we employ first-principles calculations to explore the structural and electronic properties of monoclinic Al2O3/Ga2O3 superlattices with varied layer thickness and to perform a comparative analysis with (AlxGa1−x)2O3 alloys. Our investigation examines the lattice constants and electronic energy bandgaps of both the superlattice structures and alloys across different Al concentrations, shedding light on the intricate relationship between composition and electronic properties. The analysis on electronic properties reveals that as the number of Al2O3 monolayers in the Al2O3/Ga2O3 superlattice rises from 2 to 6 monolayers, the bandgap correspondingly expands from 5.29 to 6.43 eV. The band alignment between monoclinic Al2O3 and Ga2O3 exhibits a type-II band alignment. The conduction and valence band offsets between the bulk material and Al2O3/Ga2O3 superlattice varies with change in the number of Al2O3 monolayers. Our study gives a deeper insight into the properties of the Al2O3/Ga2O3 superlattice and suggests a solution to the Al-phase separation issue in (AlxGa1−x)2O3 alloys for advanced semiconductor device applications.