Yanming Cheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yanming Cheng has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Il-Kyoo Lee
Department of Electrical, Electronics & Control Engineering 공주대학교 전기전자제어공학과 Kongju National University)
7 shared publications - Jing Wu
College of Electrical & Information Engineering, Beihua University, Jilin, China
5 shared publications Ilkyoo Lee
Division of Electrical, Electronics & Control Engineering, Kongju National University, Chungcheongnam-do, South Korea
4 shared publications- Mahmoud Al Shurafa
College of Electrical and Information Engineering, Beihua University, Jilin, China
4 shared publications - Cheng Liu
College of Electrical and Information Engineering, Beihua University, Jilin 132000, China
3 shared publications Chao Ding
College of Electrical & Information Engineering, Beihua University, Jilin, China
2 shared publications
Latest Publications
- Open Access
- 11 October 2023
- Published by SAGE Publications in Measurement and Control
- Vol. 57 (4) , 391-403
A enhanced control strategy for capacitance voltage equalization in modular multilevel converter
In searching for the optimal control strategy of sub-module capacitance voltage equalization of Modular Multilevel Converter (MMC), the most important issue is how to address the significant increase in computing time of the controller, switching frequency of the sub-module, device switching loss and MMC fault rate led by the increase in the number of sub-modules of the upper/lower bridge arm of the MMC. Therefore, this paper proposes a control strategy based on the retaining factor method + improved quick sort, namely, an improved quick sort algorithm is used to sort the sub-module capacitance voltages to reduce the amount of computation of the MMC controller; at the same time, a retaining factor is introduced to participate in the improved quick sort to significantly reduce the switching frequency of the sub-module. MMC of large ship grid-connected photovoltaic power system is taken as a research object in this paper, a 31-level MMC model is built in Matlab/Simulink. Simulation results verify that the improved quick sort has a good rapidity compared to the algorithms of bubble sort, quick sort, bidirectional bubble sort, and improved merge sort, that the retention factor method has a good frequency reduction effect, and that the proposed retention factor + improved quick sort can provide a good performance compared to improved quick sort and retention factor + improved merge sort under conditions of the normal operation and introducing disturbance.
- 11 October 2023
- Published by SAGE Publications in Measurement and Control
- Vol. 57 (4) , 391-403
Open AccessA enhanced control strategy for capacitance voltage equalization in modular multilevel converter
In searching for the optimal control strategy of sub-module capacitance voltage equalization of Modular Multilevel Converter (MMC), the most important issue is how to address the significant increase in computing time of the controller, switching frequency of the sub-module, device switching loss and MMC fault rate led by the increase in the number of sub-modules of the upper/lower bridge arm of the MMC. Therefore, this paper proposes a control strategy based on the retaining factor method + improved quick sort, namely, an improved quick sort algorithm is used to sort the sub-module capacitance voltages to reduce the amount of computation of the MMC controller; at the same time, a retaining factor is introduced to participate in the improved quick sort to significantly reduce the switching frequency of the sub-module. MMC of large ship grid-connected photovoltaic power system is taken as a research object in this paper, a 31-level MMC model is built in Matlab/Simulink. Simulation results verify that the improved quick sort has a good rapidity compared to the algorithms of bubble sort, quick sort, bidirectional bubble sort, and improved merge sort, that the retention factor method has a good frequency reduction effect, and that the proposed retention factor + improved quick sort can provide a good performance compared to improved quick sort and retention factor + improved merge sort under conditions of the normal operation and introducing disturbance.
- Open Access
- 2 November 2022
- Published by SAGE Publications in Measurement and Control
- Vol. 56 (3-4) , 694-703
An active disturbance rejection synchronous control strategy based on cross compensation for stepper motor XY platform
In view of the system uncertainty factors and bilateral drive synchronization problems of XY platform driven by stepping motor, on the basis of the mathematical model of single axis servo system, in order to improve traceability and disturbance rejection in X,Y direction, a double loop structure with PID controller as speed loop and active disturbance rejection as position loop is proposed to solve the contradiction between rapidity and overshoot, moreover, an ESO performance analysis method is proposed, and the parameter tuning rules of ADRC is summarized. On this basis, a deviation self-coupling compensation control strategy is proposed to solve the problem of bilateral drive synchronization in axis X direction, and the mechanism and parameter adjusting method of the compensator are studied. The comparative experiment between ADRC+PID+deviation self-coupling compensation and PID+PID+deviation self-coupling compensation, the comparative experiment between ADRC+PID+deviation self-coupling compensation and ADRC+PID are conducted, respectively. Finally, the experiment of synthetic trajectory of X and Y is carried out, the simulation and experimental results demonstrate that the response time of the control strategy proposed in this paper is 0.5 s, which is 0.2 s faster than PID’s, and the disturbance recovery time is 50% of PID control. Therefore, the proposed ADRC+PID+deviation self-coupling compensation control strategy can not only effectively improve the tracking performance of the XY platform system, but also enhance the robustness of the system.
- 2 November 2022
- Published by SAGE Publications in Measurement and Control
- Vol. 56 (3-4) , 694-703
Open AccessAn active disturbance rejection synchronous control strategy based on cross compensation for stepper motor XY platform
In view of the system uncertainty factors and bilateral drive synchronization problems of XY platform driven by stepping motor, on the basis of the mathematical model of single axis servo system, in order to improve traceability and disturbance rejection in X,Y direction, a double loop structure with PID controller as speed loop and active disturbance rejection as position loop is proposed to solve the contradiction between rapidity and overshoot, moreover, an ESO performance analysis method is proposed, and the parameter tuning rules of ADRC is summarized. On this basis, a deviation self-coupling compensation control strategy is proposed to solve the problem of bilateral drive synchronization in axis X direction, and the mechanism and parameter adjusting method of the compensator are studied. The comparative experiment between ADRC+PID+deviation self-coupling compensation and PID+PID+deviation self-coupling compensation, the comparative experiment between ADRC+PID+deviation self-coupling compensation and ADRC+PID are conducted, respectively. Finally, the experiment of synthetic trajectory of X and Y is carried out, the simulation and experimental results demonstrate that the response time of the control strategy proposed in this paper is 0.5 s, which is 0.2 s faster than PID’s, and the disturbance recovery time is 50% of PID control. Therefore, the proposed ADRC+PID+deviation self-coupling compensation control strategy can not only effectively improve the tracking performance of the XY platform system, but also enhance the robustness of the system.
- Open Access
- 1 July 2022
- Published by SAGE Publications in Measurement and Control
- Vol. 55 (7-8) , 757-766
Research on MPDPC with FADRC control strategy for three-phase rectifying converter
Due to unpredictable factors, the model predictive direct power control (MPDPC) exists weak robustness when the parameters change of three-phase rectifying converter. Therefore, this paper introduced Fractional Active Disturbance Rejection Control (FADRC) into the MPDPC system to improve the robustness of rectifying converter, that is, the power loop of PID controller in conventional model predictive control is replaced by FADRC. In order to verify the effectiveness of the proposed control strategy in this paper, a model of three-phase rectifying converter is established in MATLAB, and the simulation is conducted. Compared with the control effects of the MPDPC with PID (MPDPC-PID) control strategy and MPDPC with Linear Active Disturbance Rejection Control (MPDPC-LADRC) under different operational scenarios, the simulation results demonstrate that the MPDPC with FADRC (MPDPC- FADRC) strategy has best disturbance rejection capability, robustness and rapidity, and it can significantly reduce the voltage fluctuation of DC bus. This study can provide a valuable guidance and reference for the design of the efficient and stable three-phase rectifying converter.
- 1 July 2022
- Published by SAGE Publications in Measurement and Control
- Vol. 55 (7-8) , 757-766
Open AccessResearch on MPDPC with FADRC control strategy for three-phase rectifying converter
Due to unpredictable factors, the model predictive direct power control (MPDPC) exists weak robustness when the parameters change of three-phase rectifying converter. Therefore, this paper introduced Fractional Active Disturbance Rejection Control (FADRC) into the MPDPC system to improve the robustness of rectifying converter, that is, the power loop of PID controller in conventional model predictive control is replaced by FADRC. In order to verify the effectiveness of the proposed control strategy in this paper, a model of three-phase rectifying converter is established in MATLAB, and the simulation is conducted. Compared with the control effects of the MPDPC with PID (MPDPC-PID) control strategy and MPDPC with Linear Active Disturbance Rejection Control (MPDPC-LADRC) under different operational scenarios, the simulation results demonstrate that the MPDPC with FADRC (MPDPC- FADRC) strategy has best disturbance rejection capability, robustness and rapidity, and it can significantly reduce the voltage fluctuation of DC bus. This study can provide a valuable guidance and reference for the design of the efficient and stable three-phase rectifying converter.
- Open Access
- 17 May 2022
- Published by Wiley in Mobile Information Systems
- Vol. 2022, 1-7
An NSCT Image Denoising Method Based on Genetic Algorithm to Optimize the Threshold
In order to solve the defect that the threshold value of the NSCT transform method is too large or the real signal coefficients are directly lost during image denoising, an adaptive threshold method of genetic algorithm is used to optimize the NSCT image denoising method. The genetic algorithm is used to generate the initial population, and the genetic operator is determined by selection, crossover, and mutation operations to achieve NSCT threshold optimization. The obtained optimized NSCT threshold is used to process different directions. The coefficients of different scales are processed by using NSCT inverse transform to obtain the denoised image. The results of the case analysis show that the proposed method is used to denoise the image, the peak signal-to-noise ratio of the image after denoising is higher than 30 dB, the image contains rich edge information and detailed information, and the denoising performance is superior.
- 17 May 2022
- Published by Wiley in Mobile Information Systems
- Vol. 2022, 1-7
Open AccessAn NSCT Image Denoising Method Based on Genetic Algorithm to Optimize the Threshold
In order to solve the defect that the threshold value of the NSCT transform method is too large or the real signal coefficients are directly lost during image denoising, an adaptive threshold method of genetic algorithm is used to optimize the NSCT image denoising method. The genetic algorithm is used to generate the initial population, and the genetic operator is determined by selection, crossover, and mutation operations to achieve NSCT threshold optimization. The obtained optimized NSCT threshold is used to process different directions. The coefficients of different scales are processed by using NSCT inverse transform to obtain the denoised image. The results of the case analysis show that the proposed method is used to denoise the image, the peak signal-to-noise ratio of the image after denoising is higher than 30 dB, the image contains rich edge information and detailed information, and the denoising performance is superior.
- 6 January 2022
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 17 (2) , 1143-1156
A new power supply strategy for high power rectifying units in electrolytic copper process
- 6 January 2022
- Published by Springer Nature in Journal of Electrical Engineering & Technology
- Vol. 17 (2) , 1143-1156
A new power supply strategy for high power rectifying units in electrolytic copper process
- Open Access
- 23 December 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-15
An Effective Harmonic Suppression Method Based on Linear Active Disturbance Rejection Control for Copper Electrowinning Rectifier
Because the harmonics in the production process of copper electrowinning have an important impact on the electrical energy consumption, it is necessary to suppress the harmonics effectively. In this paper, a copper electrowinning rectifier with double inverse star circuit is selected as a study object in which a large number of harmonics mainly including the 5th, 7th, 11th, and 13th harmonics are generated and injected back into the power grid. The total harmonic distortion rate of the power grid is up to 29.19% before filtering. Therefore, a method combining the induction filtering method and the active filtering method is proposed to carry out comprehensive filtering. Simulation results demonstrate that the total harmonic distortion rate of the system decreases to 4.20%, which indicates that the proposed method can track the corresponding changes of harmonics when the load changes in real time and filter them out. In order to ensure and improve the effect of active filter, a current harmonic tracking control method based on linear active disturbance rejection control is proposed. Simulation results show that the total harmonic distortion rate decreases to 3.34%, which is also lower than that of hysteresis control. Compared with the conventional single filtering method, the new filtering method combining induction filtering with active filtering based on linear active disturbance rejection control in the copper electrowinning rectifier has obvious advantages.
- 23 December 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-15
Open AccessAn Effective Harmonic Suppression Method Based on Linear Active Disturbance Rejection Control for Copper Electrowinning Rectifier
Because the harmonics in the production process of copper electrowinning have an important impact on the electrical energy consumption, it is necessary to suppress the harmonics effectively. In this paper, a copper electrowinning rectifier with double inverse star circuit is selected as a study object in which a large number of harmonics mainly including the 5th, 7th, 11th, and 13th harmonics are generated and injected back into the power grid. The total harmonic distortion rate of the power grid is up to 29.19% before filtering. Therefore, a method combining the induction filtering method and the active filtering method is proposed to carry out comprehensive filtering. Simulation results demonstrate that the total harmonic distortion rate of the system decreases to 4.20%, which indicates that the proposed method can track the corresponding changes of harmonics when the load changes in real time and filter them out. In order to ensure and improve the effect of active filter, a current harmonic tracking control method based on linear active disturbance rejection control is proposed. Simulation results show that the total harmonic distortion rate decreases to 3.34%, which is also lower than that of hysteresis control. Compared with the conventional single filtering method, the new filtering method combining induction filtering with active filtering based on linear active disturbance rejection control in the copper electrowinning rectifier has obvious advantages.
- Open Access
- 23 September 2021
- Published by Wiley in Mobile Information Systems
- Vol. 2021, 1-8
Research on Beauty Medical Health Monitoring System Based on Wireless Sensor Network
Due to the gradual improvement of living standards in recent years and the continuous improvement of Chinas health care awareness, the aesthetic medicine model has gradually changed from the treatment mode of disease treatment to the prevention mode of early detection and early treatment. Meanwhile, wireless sensor networks (WSNs) are gradually infiltrating into the medical field due to their low power consumption, small size, wireless transmission, and portability which complies with the needs of the development of medical models. Therefore, this paper studies and implements a beauty medical health monitoring system based on WSN and ZigBee short-range wireless transmission protocol; moreover, wireless power transfer (WPT) technology is used for charging sensors. Experimental results demonstrate the feasibility that the maximum power levels converted in sensors by the WPT for different ISM bands can meet the average power consumption expected in the range of 200500μW. And the designed system can provide an important practical reference for promoting the informationization of telemedicine and the development of beauty medical systems in China.
- 23 September 2021
- Published by Wiley in Mobile Information Systems
- Vol. 2021, 1-8
Open AccessResearch on Beauty Medical Health Monitoring System Based on Wireless Sensor Network
Due to the gradual improvement of living standards in recent years and the continuous improvement of Chinas health care awareness, the aesthetic medicine model has gradually changed from the treatment mode of disease treatment to the prevention mode of early detection and early treatment. Meanwhile, wireless sensor networks (WSNs) are gradually infiltrating into the medical field due to their low power consumption, small size, wireless transmission, and portability which complies with the needs of the development of medical models. Therefore, this paper studies and implements a beauty medical health monitoring system based on WSN and ZigBee short-range wireless transmission protocol; moreover, wireless power transfer (WPT) technology is used for charging sensors. Experimental results demonstrate the feasibility that the maximum power levels converted in sensors by the WPT for different ISM bands can meet the average power consumption expected in the range of 200500μW. And the designed system can provide an important practical reference for promoting the informationization of telemedicine and the development of beauty medical systems in China.
- Open Access
- 24 June 2021
- Published by Wiley in Mobile Information Systems
- Vol. 2021, 1-10
Research on the Smart Medical System Based on NB-IoT Technology
In recent years, with the constant development and integration of Internet technology, Internet of Things technology, and intelligent terminal technology, to make people’s work and life more comfortable and convenient, these new technologies have been more and more widely used in daily home life such as social education, agricultural production, industrial production, medical, and other fields. However, at present, there are still a lot of room for development in the application of new technologies in the medical and health industry. Especially in the context of hospital information construction and medical difficulties, the functions of fixed information points such as traditional nurse stations and doctor stations no longer meet the growing medical needs of people. Therefore, how to introduce these new technologies and design to a practical and low-cost intelligent medical information management system that realizes the convenient management and efficient management of medical personnel has become a top priority. In view of the problems faced by the hospital, this paper proposes an intelligent medical plan based on NB-IoT technology and develops a smart hospital information management system. Test results indicate that patients can easily and conveniently register their appointments through the Android mobile client. Through checking medical records and hospital news updates, medical staff can more easily complete their work. Comparison results of performance variance between the common server and adaptive algorithm web server demonstrate that an adaptive load balancing algorithm can achieve a more accurate allocation of the load. Therefore, the web smart medical information management platform can manage hospitals more comprehensively.
- 24 June 2021
- Published by Wiley in Mobile Information Systems
- Vol. 2021, 1-10
Open AccessResearch on the Smart Medical System Based on NB-IoT Technology
In recent years, with the constant development and integration of Internet technology, Internet of Things technology, and intelligent terminal technology, to make people’s work and life more comfortable and convenient, these new technologies have been more and more widely used in daily home life such as social education, agricultural production, industrial production, medical, and other fields. However, at present, there are still a lot of room for development in the application of new technologies in the medical and health industry. Especially in the context of hospital information construction and medical difficulties, the functions of fixed information points such as traditional nurse stations and doctor stations no longer meet the growing medical needs of people. Therefore, how to introduce these new technologies and design to a practical and low-cost intelligent medical information management system that realizes the convenient management and efficient management of medical personnel has become a top priority. In view of the problems faced by the hospital, this paper proposes an intelligent medical plan based on NB-IoT technology and develops a smart hospital information management system. Test results indicate that patients can easily and conveniently register their appointments through the Android mobile client. Through checking medical records and hospital news updates, medical staff can more easily complete their work. Comparison results of performance variance between the common server and adaptive algorithm web server demonstrate that an adaptive load balancing algorithm can achieve a more accurate allocation of the load. Therefore, the web smart medical information management platform can manage hospitals more comprehensively.
- Open Access
- 26 March 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-14
A Novel PID Control Strategy Based on Improved GA-BP Neural Network for Phase-Shifted Full-Bridge Current-Doubler Synchronous Rectifying Converter
In this paper, a phase-shifted full-bridge current-doubler synchronous rectifying converter (PSFB-CDSRC) based on IGBT and its control strategies are studied. In the main circuit, a current doubling synchronous rectifying circuit based on IGBT is presented to further reduce the power loss of power devices. Moreover, in the control strategy, in view of the existing researches, the basic BP neural network PID control performance of the rectifying converter still can be further improved. Therefore, this paper combines the quasi-Newton algorithm and traditional GA to propose an improved GA-BP (IGA-BP) neural network to further improve PID control performance. The simulation results demonstrate that the maximum efficiency of 5 V/500 A rectifying converter based on the proposed circuit scheme can reach 94.1%, and the rectifying converter has a good performance of excellent waveform and wide range of load. IGA-BP neural network PID control responds fast and reaches the stable state quickly in comparison with that controlled by the GA-BP neural network control strategy, and the steady-state time can be reduced by 10.5% through using IGA-BP neural network control strategy. This study can provide a valuable guidance and reference, not only in circuit scheme but also in the optimal PID control strategy for design of the high-efficiency DC/DC rectifying converter with higher power in the future.
- 26 March 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-14
Open AccessA Novel PID Control Strategy Based on Improved GA-BP Neural Network for Phase-Shifted Full-Bridge Current-Doubler Synchronous Rectifying Converter
In this paper, a phase-shifted full-bridge current-doubler synchronous rectifying converter (PSFB-CDSRC) based on IGBT and its control strategies are studied. In the main circuit, a current doubling synchronous rectifying circuit based on IGBT is presented to further reduce the power loss of power devices. Moreover, in the control strategy, in view of the existing researches, the basic BP neural network PID control performance of the rectifying converter still can be further improved. Therefore, this paper combines the quasi-Newton algorithm and traditional GA to propose an improved GA-BP (IGA-BP) neural network to further improve PID control performance. The simulation results demonstrate that the maximum efficiency of 5 V/500 A rectifying converter based on the proposed circuit scheme can reach 94.1%, and the rectifying converter has a good performance of excellent waveform and wide range of load. IGA-BP neural network PID control responds fast and reaches the stable state quickly in comparison with that controlled by the GA-BP neural network control strategy, and the steady-state time can be reduced by 10.5% through using IGA-BP neural network control strategy. This study can provide a valuable guidance and reference, not only in circuit scheme but also in the optimal PID control strategy for design of the high-efficiency DC/DC rectifying converter with higher power in the future.
- Open Access
- 24 March 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-13
A Novel Smith Predictive Linear Active Disturbance Rejection Control Strategy for the First-Order Time-Delay Inertial System
The control strategy research of the time-delay system is a focused issue in the control field. In order to furthermore improve the performance of the first-order time-delay inertial system, firstly, a new Smith predictor structure is proposed, which solves the constraint that the conventional Smith predictor needs to match the actual object model. Secondly, the performance and parameter function of the new Smith predictor are discussed in theory to provide the basis for parameter tuning. Finally, a new Smith predictor combined with linear active disturbance rejection control (LADRC) is proposed to solve the problem that the two input signals of the linear extended state observer (LESO) are not synchronized on the time scale, and the stability of the new Smith + LADRC time-delay control system is proved theoretically for known and unknown controlled complex objects. Simulation analysis is conducted to verify the robustness of the proposed strategy under the condition of the different parameters. The results indicate that the proposed strategy has better performance than the conventional method in response speed, overshoot, adjustment time, and stability.
- 24 March 2021
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2021, 1-13
Open AccessA Novel Smith Predictive Linear Active Disturbance Rejection Control Strategy for the First-Order Time-Delay Inertial System
The control strategy research of the time-delay system is a focused issue in the control field. In order to furthermore improve the performance of the first-order time-delay inertial system, firstly, a new Smith predictor structure is proposed, which solves the constraint that the conventional Smith predictor needs to match the actual object model. Secondly, the performance and parameter function of the new Smith predictor are discussed in theory to provide the basis for parameter tuning. Finally, a new Smith predictor combined with linear active disturbance rejection control (LADRC) is proposed to solve the problem that the two input signals of the linear extended state observer (LESO) are not synchronized on the time scale, and the stability of the new Smith + LADRC time-delay control system is proved theoretically for known and unknown controlled complex objects. Simulation analysis is conducted to verify the robustness of the proposed strategy under the condition of the different parameters. The results indicate that the proposed strategy has better performance than the conventional method in response speed, overshoot, adjustment time, and stability.