Benjamin Zenker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Benjamin Zenker has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Ercan Altinsoy
Chair of Acoustics and Haptics, Faculty of Electrical Engineering, Technische Universität Dresden, 01062 Dresden, Germany
3 shared publications - Robert Schurmann
Chair of Acoustic und Haptic Engineering, Technical University of Dresden, Helmholtzstrasse 18, 01069 Dresden, Germany
2 shared publications - Sebastian Merchel
Tech Univ Dresden, Chair Acoust & Hapt Engn, Dresden, Germany
2 shared publications - Klaudiusz Holeczek
Institute of Lightweight Engineering and Polymer Technology (ILK), Technische Universität Dresden (TUD), Dresden, Germany
1 shared publication - Martin Dannemann
Faculty of Automotive Engineering, Institute of Energy and Transport Engineering, Westsächsische Hochschule Zwickau, 08056 Zwickau, Germany
1 shared publication - Niels Modler
Institute of Lightweight Engineering and Polymer Technology, Dresden University of Technology, 01307 Dresden, Germany
1 shared publication
Latest Publications
- Open Access
- 29 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (15) , 7001
Improved Directivity of Flat Panel Loudspeakers by Minimizing the Off-Axis Radiation below Coincidence
Flat panel loudspeakers are a promising alternative to conventional loudspeakers. In particular, quasi-omnidirectional radiation at higher frequencies is stressed as an advantage of these systems compared to conventional speaker systems. However, this advantage can also be considered a disadvantage. Compared to that from conventional speakers with a flat and smooth on-axis and off-axis response, this wide radiation from flat panel loudspeakers occurs with an inconstant directivity factor, which can cause coloration and unusual spatial artifacts. This paper investigated the root causes of inhomogeneous directivity by using numerical methods. Based on these analyses, specific prototypes with various damping layups were built to overcome this problem. The additional damping layer reduces the off-axis radiation without significantly reducing the pressure level in the listening window. This approach is simple, robust, inexpensive and effective for improving the directivity of flat panel loudspeakers.
- 29 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (15) , 7001
Open AccessImproved Directivity of Flat Panel Loudspeakers by Minimizing the Off-Axis Radiation below Coincidence
Flat panel loudspeakers are a promising alternative to conventional loudspeakers. In particular, quasi-omnidirectional radiation at higher frequencies is stressed as an advantage of these systems compared to conventional speaker systems. However, this advantage can also be considered a disadvantage. Compared to that from conventional speakers with a flat and smooth on-axis and off-axis response, this wide radiation from flat panel loudspeakers occurs with an inconstant directivity factor, which can cause coloration and unusual spatial artifacts. This paper investigated the root causes of inhomogeneous directivity by using numerical methods. Based on these analyses, specific prototypes with various damping layups were built to overcome this problem. The additional damping layer reduces the off-axis radiation without significantly reducing the pressure level in the listening window. This approach is simple, robust, inexpensive and effective for improving the directivity of flat panel loudspeakers.
- Open Access
- 14 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (24) , 8926
Improved Sound Radiation of Flat Panel Loudspeakers Using the Local Air Spring Effect
The low-frequency performance of exciter-driven flat-panel loudspeakers is technically challenging. The lower modal density results in high deviations in the frequency response, and dips of more than 20 dB are possible. This paper presents an alternative approach for optimizing the modal behavior through the additional air spring effect of an irregular shaped enclosure. The additional mode-dependent air compliance suppresses the panel’s anti-phase components, which minimizes dips in the frequency response and improves the response without adding mass to the system. The approach is analyzed with the measured and simulated results of a prototype. Furthermore, additional enclosure changes were made to visualize the influence of the air spring improved system.
- 14 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (24) , 8926
Open AccessImproved Sound Radiation of Flat Panel Loudspeakers Using the Local Air Spring Effect
The low-frequency performance of exciter-driven flat-panel loudspeakers is technically challenging. The lower modal density results in high deviations in the frequency response, and dips of more than 20 dB are possible. This paper presents an alternative approach for optimizing the modal behavior through the additional air spring effect of an irregular shaped enclosure. The additional mode-dependent air compliance suppresses the panel’s anti-phase components, which minimizes dips in the frequency response and improves the response without adding mass to the system. The approach is analyzed with the measured and simulated results of a prototype. Furthermore, additional enclosure changes were made to visualize the influence of the air spring improved system.
- Open Access
- 16 May 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (10) , 3438
Structure-Integrated Loudspeaker Using Fiber-Reinforced Plastics and Piezoelectric Transducers—Design, Manufacturing and Validation
In the present study, it could be shown that by integration of a piezoceramic transducer in a fiber-reinforced door side panel, a flat loudspeaker can be realized. Taking into account the given restrictions, the integration position has been identified, where the geometry decouples the vibrating membrane from the supporting surface. With the help of an acoustic finite-element simulation, the main design variables of the integration position were found and the relevant effects for sound radiation were made visible. The manufacturing of the test specimen with piezoceramic transducers was performed using vacuum-assisted resin infusion and the long fiber injection procedure. The effect on the real sound radiation behavior of the door side panel with a material-immanent loudspeaker was experimentally determined using laser scanning vibrometry and sound pressure measurements. The presented work shows, for the first time, the high potential of acoustic functionalization of lightweight structures during the manufacturing process for the realization of lightweight and space-saving loudspeakers in a production-ready process.
- 16 May 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (10) , 3438
Open AccessStructure-Integrated Loudspeaker Using Fiber-Reinforced Plastics and Piezoelectric Transducers—Design, Manufacturing and Validation
In the present study, it could be shown that by integration of a piezoceramic transducer in a fiber-reinforced door side panel, a flat loudspeaker can be realized. Taking into account the given restrictions, the integration position has been identified, where the geometry decouples the vibrating membrane from the supporting surface. With the help of an acoustic finite-element simulation, the main design variables of the integration position were found and the relevant effects for sound radiation were made visible. The manufacturing of the test specimen with piezoceramic transducers was performed using vacuum-assisted resin infusion and the long fiber injection procedure. The effect on the real sound radiation behavior of the door side panel with a material-immanent loudspeaker was experimentally determined using laser scanning vibrometry and sound pressure measurements. The presented work shows, for the first time, the high potential of acoustic functionalization of lightweight structures during the manufacturing process for the realization of lightweight and space-saving loudspeakers in a production-ready process.