Kody Wolfe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Kody Wolfe has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Jason Trembly
Ohio Univ., Athens, OH (United States)
10 shared publications - David E. Cliffel
Vanderbilt University
7 shared publications - Gannon Kane Jennings
Department of Chemical and Biomolecular Engineering, Vanderbilt University, Nashville, TN, USA
7 shared publications - John A. Staser
Institute for Sustainable Energy and the Environment, Ohio University, Athens, Ohio 45701, United States of America
6 shared publications - Abigail Paul
Ohio University
5 shared publications - Taylor Reed Garrick
Global Virtual Electrification and Powertrain, General Motors, Warren, Michigan 48092
5 shared publications
Latest Publications
- 10 July 2026
- Published by Office of Scientific and Technical Information (OSTI)
Combined Nitrogen and Phosphorous Recovery via Electrochemical Technology Integration into Municipal Wastewater Treatment Plants
This project developed electroN-P, an electrochemical technology for recovering nitrogen and phosphorus as a fertilizer product from anaerobic digester centrate, targeting an advancement from TRL 4 to 6. The reactor was scaled 220× from a 250 mL batch cell to a continuous 4-channel system treating 55 L of wastewater, recovering >80% of phosphorus. Energy consumption under constant-voltage operation was lower than the embedded energy of conventional fertilizers, while constant-current operation produced a cost-competitive product with a smaller reactor footprint. TEA and LCA outcomes were highly sensitive to the magnesium source; alternative magnesium salt configurations projected reduced costs and embedded energy compared to sacrificial rods, but at the expense of significantly longer operation times. The recovered fertilizer performed comparably to diammonium phosphate and triple superphosphate in soil and plant trials. Integrating the technology into a whole-plant model reduced aeration energy by nearly 50%, lowering the levelized cost of water treatment from $0.668/m3 to $0.648/m3. Results support targeting commercialization at smaller (≤1 MGD) facilities with high-strength digester streams. Further investigation into the transport and corrosion kinetics governing sacrificial anode wear is recommended to support continuous, longer-term operation.
- 10 July 2026
- Published by Office of Scientific and Technical Information (OSTI)
Combined Nitrogen and Phosphorous Recovery via Electrochemical Technology Integration into Municipal Wastewater Treatment Plants
This project developed electroN-P, an electrochemical technology for recovering nitrogen and phosphorus as a fertilizer product from anaerobic digester centrate, targeting an advancement from TRL 4 to 6. The reactor was scaled 220× from a 250 mL batch cell to a continuous 4-channel system treating 55 L of wastewater, recovering >80% of phosphorus. Energy consumption under constant-voltage operation was lower than the embedded energy of conventional fertilizers, while constant-current operation produced a cost-competitive product with a smaller reactor footprint. TEA and LCA outcomes were highly sensitive to the magnesium source; alternative magnesium salt configurations projected reduced costs and embedded energy compared to sacrificial rods, but at the expense of significantly longer operation times. The recovered fertilizer performed comparably to diammonium phosphate and triple superphosphate in soil and plant trials. Integrating the technology into a whole-plant model reduced aeration energy by nearly 50%, lowering the levelized cost of water treatment from $0.668/m3 to $0.648/m3. Results support targeting commercialization at smaller (≤1 MGD) facilities with high-strength digester streams. Further investigation into the transport and corrosion kinetics governing sacrificial anode wear is recommended to support continuous, longer-term operation.
- Open Access
- 1 July 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (7) , 073501
Anion Influence on Graphene Yield from Anodic Exfoliation of Coal-Derived Graphite: A Novel Precursor for Graphene Production
This study represents a significant advancement in graphene production through the electrochemical exfoliation of coal-derived graphite, focusing on anodic processes. Carbon foams, known for their lightweight structure and excellent electrical, mechanical, and thermal properties, were the starting material. The resulting graphene was analyzed for its morphology (scanning electron microscopy, field-emission scanning electron microcopy, transmission electron microscopy, atomic force microscopy), structural characteristics (Raman, X-ray diffraction), and chemical properties (Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy). The findings indicate that coal-derived graphite is a promising alternative for graphene production. The study also explores how different aqueous electrolytes affect the exfoliation process, focusing on the roles of anions as the active intercalants in anodic exfoliation. Specifically, Na2SO4 and KCl electrolytes were investigated. Exfoliation with KCl, involving chloride anions, produces graphene with fewer defects and a more ordered structure. In contrast, exfoliation with Na2SO4, driven by sulfate anions, results in graphene with more defects and oxygen-containing functional groups. These findings emphasize the critical role of the chemical environment in shaping the quality of exfoliated graphene, reinforcing coal-derived graphite as a promising graphene source.
- 1 July 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (7) , 073501
Open AccessAnion Influence on Graphene Yield from Anodic Exfoliation of Coal-Derived Graphite: A Novel Precursor for Graphene Production
This study represents a significant advancement in graphene production through the electrochemical exfoliation of coal-derived graphite, focusing on anodic processes. Carbon foams, known for their lightweight structure and excellent electrical, mechanical, and thermal properties, were the starting material. The resulting graphene was analyzed for its morphology (scanning electron microscopy, field-emission scanning electron microcopy, transmission electron microscopy, atomic force microscopy), structural characteristics (Raman, X-ray diffraction), and chemical properties (Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy). The findings indicate that coal-derived graphite is a promising alternative for graphene production. The study also explores how different aqueous electrolytes affect the exfoliation process, focusing on the roles of anions as the active intercalants in anodic exfoliation. Specifically, Na2SO4 and KCl electrolytes were investigated. Exfoliation with KCl, involving chloride anions, produces graphene with fewer defects and a more ordered structure. In contrast, exfoliation with Na2SO4, driven by sulfate anions, results in graphene with more defects and oxygen-containing functional groups. These findings emphasize the critical role of the chemical environment in shaping the quality of exfoliated graphene, reinforcing coal-derived graphite as a promising graphene source.
- Open Access
- 28 April 2025
- Published by Wiley in Energy Science & Engineering
- Vol. 13 (7) , 3678-3687
Semi‐Continuous Ex Situ Carbon Dioxide Mineralization in Produced Water for Calcite Production
The mineralization of carbon dioxide (CO2) to stable carbonate products is a desirable process for carbon capture utilization and storage (CCUS). However, improving the process economics through creative use of available reactants is necessary to develop a scalable mineralization process. This study details the development of a semi‐continuous CO2 mineralization process that uses flue gas as a point CO2 source, produced water (PW) as an alkaline source of Ca2+, and NaOH effluent (potentially sourced from integration with the chlor‐alkali process. Operating at a controlled pH allowed for both complete reaction of available Ca2+ (100% carbonation potential or 9.9 g CO2.L–1 PW brine) and for reproducible control of the produced calcium carbonate (CaCO3) product. A full factorial design of experiments was implemented to study the effects of reaction temperature, pH, and gaseous CO2 concentration on the mineralization and CO2 capture rates as well as product crystalline structure and morphology. A maximum CO2 capture rate of 0.315 ± 0.007 kg.L–1.d–1 was achieved at 25°C and 25% CO2. CO2 gas to liquid phase mass transport is believed to be the rate limiting step. With improved reactor design and optimization, the proposed semi‐continuous mineralization process shows promise for scaling to a pilot scale CO2 capture technology.
- 28 April 2025
- Published by Wiley in Energy Science & Engineering
- Vol. 13 (7) , 3678-3687
Open AccessSemi‐Continuous Ex Situ Carbon Dioxide Mineralization in Produced Water for Calcite Production
The mineralization of carbon dioxide (CO2) to stable carbonate products is a desirable process for carbon capture utilization and storage (CCUS). However, improving the process economics through creative use of available reactants is necessary to develop a scalable mineralization process. This study details the development of a semi‐continuous CO2 mineralization process that uses flue gas as a point CO2 source, produced water (PW) as an alkaline source of Ca2+, and NaOH effluent (potentially sourced from integration with the chlor‐alkali process. Operating at a controlled pH allowed for both complete reaction of available Ca2+ (100% carbonation potential or 9.9 g CO2.L–1 PW brine) and for reproducible control of the produced calcium carbonate (CaCO3) product. A full factorial design of experiments was implemented to study the effects of reaction temperature, pH, and gaseous CO2 concentration on the mineralization and CO2 capture rates as well as product crystalline structure and morphology. A maximum CO2 capture rate of 0.315 ± 0.007 kg.L–1.d–1 was achieved at 25°C and 25% CO2. CO2 gas to liquid phase mass transport is believed to be the rate limiting step. With improved reactor design and optimization, the proposed semi‐continuous mineralization process shows promise for scaling to a pilot scale CO2 capture technology.
- Open Access
Long-Term Stability of Nicotinamide Cofactors in Common Aqueous Buffers: Implications for Cell-Free Biocatalysis
The use of nicotinamide cofactors in cell-free biocatalytic systems is necessitated by the high specificity that these enzymes show for their natural redox mediators. Unfortunately, isolation and use of natural cofactors is costly, which suggests that enhancing their stability is key to enabling their use in industrial processes. This study details NAD+ and NADH stability in three buffer systems (sodium phosphate, HEPES, and Tris) at 19 °C and 25 °C and for up to 43 d. In Tris, both NADH and NAD+ were found to be highly stable. NADH degradation rates of 4 μM/d (19 °C) and 11 μM/d (25 °C) were observed in Tris buffer, corresponding to >90% and 75% remaining after 43 d, respectively. Higher degradation rates (up to 34 μM/d) were observed when sodium phosphate or HEPES buffers were used. The effect of a mild increase in temperature was determined to be significant for long-term stability, and it was shown that degradation under these conditions can be easily monitored via UV–Vis, because the degradation proceeds via the oxidation/de-aromatization of the dihydropyridine ring. Overall, this work emphasizes that the choice of buffer system is consequential for bioreactor systems employing natural nicotinamide cofactors for extended periods of time.
Open AccessLong-Term Stability of Nicotinamide Cofactors in Common Aqueous Buffers: Implications for Cell-Free Biocatalysis
The use of nicotinamide cofactors in cell-free biocatalytic systems is necessitated by the high specificity that these enzymes show for their natural redox mediators. Unfortunately, isolation and use of natural cofactors is costly, which suggests that enhancing their stability is key to enabling their use in industrial processes. This study details NAD+ and NADH stability in three buffer systems (sodium phosphate, HEPES, and Tris) at 19 °C and 25 °C and for up to 43 d. In Tris, both NADH and NAD+ were found to be highly stable. NADH degradation rates of 4 μM/d (19 °C) and 11 μM/d (25 °C) were observed in Tris buffer, corresponding to >90% and 75% remaining after 43 d, respectively. Higher degradation rates (up to 34 μM/d) were observed when sodium phosphate or HEPES buffers were used. The effect of a mild increase in temperature was determined to be significant for long-term stability, and it was shown that degradation under these conditions can be easily monitored via UV–Vis, because the degradation proceeds via the oxidation/de-aromatization of the dihydropyridine ring. Overall, this work emphasizes that the choice of buffer system is consequential for bioreactor systems employing natural nicotinamide cofactors for extended periods of time.
- Open Access
- 1 October 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (10) , 103505
Quantifying the Temperature Dependence of the Multi-Species, Multi-Reaction Model: Part II. Estimation of Entropy Coefficient for Meso-Carbon Micro-Bead Graphite
In Part 1 of this paper, the temperature impact on the Multi-Species, Multi Reaction (MSMR) model was studied. This was accomplished by acquiring data from slow rate lithiation and delithiation of a meso-carbon micro-bead (MCMB) graphite. Through this analysis, the temperature impact on the total fraction of available host sites in a particular MSMR gallery (Xj), the impact on the reference potential ( U j o ), and the impact on the parameter detailing the deviation from Nernstian behavior (ω j) was determined. Here, the intercalation material is discussed, compared to traditional methods of acquiring the entropy coefficient, and comparison is made to previous mathematical estimates. Some of the challenges in using temperature dependent constant rate charge and discharge data as compared to the potentiodynamic entropy coefficient calculation method are also discussed, and a recommendation for future applications is proposed.
- 1 October 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (10) , 103505
Open AccessQuantifying the Temperature Dependence of the Multi-Species, Multi-Reaction Model: Part II. Estimation of Entropy Coefficient for Meso-Carbon Micro-Bead Graphite
In Part 1 of this paper, the temperature impact on the Multi-Species, Multi Reaction (MSMR) model was studied. This was accomplished by acquiring data from slow rate lithiation and delithiation of a meso-carbon micro-bead (MCMB) graphite. Through this analysis, the temperature impact on the total fraction of available host sites in a particular MSMR gallery (Xj), the impact on the reference potential ( U j o ), and the impact on the parameter detailing the deviation from Nernstian behavior (ω j) was determined. Here, the intercalation material is discussed, compared to traditional methods of acquiring the entropy coefficient, and comparison is made to previous mathematical estimates. Some of the challenges in using temperature dependent constant rate charge and discharge data as compared to the potentiodynamic entropy coefficient calculation method are also discussed, and a recommendation for future applications is proposed.
- Open Access
- 1 October 2024
- Published by The Electrochemical Society in ECS Advances
- Vol. 3 (4) , 042501
Quantifying the Temperature Dependence of the Multi-Species, Multi-Reaction Model. Part 1: Parameterization for a Meso-Carbon Micro-Bead Graphite
In this work, the temperature impact on the Multi-Species, Multi-Reaction (MSMR) model is studied. This is accomplished by acquiring data from slow rate lithiation and delithiation of a meso-carbon micro-bead (MCMB) graphite. The MSMR model is used to simulate linear-sweep voltammetry data of a porous electrode composed of graphite, and because the electrode is close to a state of dynamic equilibrium, the peaks in the differential voltage spectroscopy plot can be analyzed. Through this analysis, the temperature impact on the total fraction of available host sites in a particular MSMR gallery (Xj), the impact on the reference potential (U°j), and the impact on the parameter detailing the deviation from Nernstian behavior (ω j) can be found. This is the first time the temperature dependence of the MSMR parameters have been experimentally analyzed. In Part 2, the impact of the temperature dependence of the MSMR parameters on the entropy coefficient of an intercalation material will be studied.
- 1 October 2024
- Published by The Electrochemical Society in ECS Advances
- Vol. 3 (4) , 042501
Open AccessQuantifying the Temperature Dependence of the Multi-Species, Multi-Reaction Model. Part 1: Parameterization for a Meso-Carbon Micro-Bead Graphite
In this work, the temperature impact on the Multi-Species, Multi-Reaction (MSMR) model is studied. This is accomplished by acquiring data from slow rate lithiation and delithiation of a meso-carbon micro-bead (MCMB) graphite. The MSMR model is used to simulate linear-sweep voltammetry data of a porous electrode composed of graphite, and because the electrode is close to a state of dynamic equilibrium, the peaks in the differential voltage spectroscopy plot can be analyzed. Through this analysis, the temperature impact on the total fraction of available host sites in a particular MSMR gallery (Xj), the impact on the reference potential (U°j), and the impact on the parameter detailing the deviation from Nernstian behavior (ω j) can be found. This is the first time the temperature dependence of the MSMR parameters have been experimentally analyzed. In Part 2, the impact of the temperature dependence of the MSMR parameters on the entropy coefficient of an intercalation material will be studied.
- Open Access
- 8 August 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Electrified Nutrient Recovery at Municipal Wastewater Facilities: Sampling, Screening and Multivariate Analyses
Municipal wastewater facilities can contain recycle streams with high nutrient content, that both increase the overall energy consumption in the facility and cause environmental pollution when not properly handled. Reducing the nutrient load of these streams through recovery is a promising solution that enhances the Food-Energy-Water nexus by producing sustainable fertilizer. In this study, the potential for nutrient recovery at municipal wastewater facilities was investigated through a 1-year sampling of nutrient, ionic, organic and heavy metal composition of three wastewater streams influent to or effluent from two types of digesters. Subsequently, electrochemical nutrient recovery was evaluated for these streams through multivariate screening of three groups of variables – operational, stream and design – and the effect of these variables on optimal nutrient recovery in the form of phosphorus. Results showed that Orthophosphate (Ortho-P) and ammonia concentrations do not show significant correlation in any tested streams. On the other hand, major ions exhibited interdependence with Ortho-P concentration, while the stream pH was found to correlate with Ortho-P and Cl- in the anaerobic digester effluent. Screening analyses identified 5 – anode type, cathodic potential, initial P concentration, initial NH4+ concentration and temperature – of the 11 variables evaluated were the variables that most significantly affected P recovery efficiency and specific energy consumed during this recovery. Finally, the optimum conditions for high phosphorus recovery and low energy consumption from the anaerobic digester effluent during a 2-hour experiment were a cathodic potential of -0.805 V vs Ag/AgClsat, an electrode area to electrolyte volume ratio of 0.145 1/cm, and a temperature of 41.3°C, with a solid product that was predominantly struvite. Overall, the demonstrated 95% P recovery efficiency and 0.03 kWh/kg P are characteristic of an emerging process that could be competitive at scale with state-of-the-art synthetic nutrient routes, if applied to the right stream.
- 8 August 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessElectrified Nutrient Recovery at Municipal Wastewater Facilities: Sampling, Screening and Multivariate Analyses
Municipal wastewater facilities can contain recycle streams with high nutrient content, that both increase the overall energy consumption in the facility and cause environmental pollution when not properly handled. Reducing the nutrient load of these streams through recovery is a promising solution that enhances the Food-Energy-Water nexus by producing sustainable fertilizer. In this study, the potential for nutrient recovery at municipal wastewater facilities was investigated through a 1-year sampling of nutrient, ionic, organic and heavy metal composition of three wastewater streams influent to or effluent from two types of digesters. Subsequently, electrochemical nutrient recovery was evaluated for these streams through multivariate screening of three groups of variables – operational, stream and design – and the effect of these variables on optimal nutrient recovery in the form of phosphorus. Results showed that Orthophosphate (Ortho-P) and ammonia concentrations do not show significant correlation in any tested streams. On the other hand, major ions exhibited interdependence with Ortho-P concentration, while the stream pH was found to correlate with Ortho-P and Cl- in the anaerobic digester effluent. Screening analyses identified 5 – anode type, cathodic potential, initial P concentration, initial NH4+ concentration and temperature – of the 11 variables evaluated were the variables that most significantly affected P recovery efficiency and specific energy consumed during this recovery. Finally, the optimum conditions for high phosphorus recovery and low energy consumption from the anaerobic digester effluent during a 2-hour experiment were a cathodic potential of -0.805 V vs Ag/AgClsat, an electrode area to electrolyte volume ratio of 0.145 1/cm, and a temperature of 41.3°C, with a solid product that was predominantly struvite. Overall, the demonstrated 95% P recovery efficiency and 0.03 kWh/kg P are characteristic of an emerging process that could be competitive at scale with state-of-the-art synthetic nutrient routes, if applied to the right stream.
- Open Access
- 7 March 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (3) , 039001
Corrigendum: Application of the Multi-Species, Multi-Reaction Model to Coal-Derived Graphite for Lithium-Ion Batteries [ J. Electrochem. Soc., 171, 023501 (2024)]
- 7 March 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (3) , 039001
Open AccessCorrigendum: Application of the Multi-Species, Multi-Reaction Model to Coal-Derived Graphite for Lithium-Ion Batteries [ J. Electrochem. Soc., 171, 023501 (2024)]
- Open Access
- 1 February 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (2) , 023501
Application of the Multi-Species, Multi-Reaction Model to Coal-Derived Graphite for Lithium-Ion Batteries
Graphite is a critical material used as the negative electrode in lithium-ion batteries. Both natural and synthetic graphites are utilized, with the latter obtained from a range of carbon raw materials. In this paper, efforts to synthesize graphite from coal as a domestic feedstock for synthetic graphite are reported. Domestic coal-derived graphite could address national security and energy issues by standing up domestic supply chains for battery critical materials. The performance in lithium-ion coin cells of this coal derived graphite is compared to a commercial battery-grade graphite. For the first time, a multi-species, multi-reaction (MSMR) modeling technique is applied to synthetic graphite derived from coal. Key thermodynamic, transport, and kinetic parameters are obtained for the coal derived graphite and compared to the same parameters for commercial battery-grade graphite. Modeling of synthetic graphites will allow for virtual evaluation of these materials toward production of domestically sourced graphite.
- 1 February 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (2) , 023501
Open AccessApplication of the Multi-Species, Multi-Reaction Model to Coal-Derived Graphite for Lithium-Ion Batteries
Graphite is a critical material used as the negative electrode in lithium-ion batteries. Both natural and synthetic graphites are utilized, with the latter obtained from a range of carbon raw materials. In this paper, efforts to synthesize graphite from coal as a domestic feedstock for synthetic graphite are reported. Domestic coal-derived graphite could address national security and energy issues by standing up domestic supply chains for battery critical materials. The performance in lithium-ion coin cells of this coal derived graphite is compared to a commercial battery-grade graphite. For the first time, a multi-species, multi-reaction (MSMR) modeling technique is applied to synthetic graphite derived from coal. Key thermodynamic, transport, and kinetic parameters are obtained for the coal derived graphite and compared to the same parameters for commercial battery-grade graphite. Modeling of synthetic graphites will allow for virtual evaluation of these materials toward production of domestically sourced graphite.