Núbia Natália de Brito
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Núbia Natália de Brito has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Carlos Rafael Dufrayer
2 shared publications- Genildo S. C. Junior2 shared publications
- Larissa Queiroz Silva
Chemistry Institute, Federal University of Goiás
2 shared publications - Pedro Lindstron Wittica Cerqueira
Goiás Sanitation Company S.A. - SANEAGO
2 shared publications Pryscilla Martins de Andrade
2 shared publications- Sarah A. D. Borges A. D. Borges
Chemistry Institute, Federal University of Goiás
2 shared publications
Latest Publications
- 1 December 2025
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 48 (4) , 1-15
The Environmental Performance of Three Sewage Treatment Plants in Goiânia, Brazil: An Application of Tertiary Treatment with Sodium Persulfate
- 1 December 2025
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 48 (4) , 1-15
The Environmental Performance of Three Sewage Treatment Plants in Goiânia, Brazil: An Application of Tertiary Treatment with Sodium Persulfate
- Open Access
- 27 August 2024
- Published by Revistas Processos Quimicos in Revista Processos Químicos
- Vol. 19 (36) , 29-33
Desempenho Ambiental da ETE Parque Atheneu, Goiânia-GO: Verificação da Aplicabilidade de Processo Oxidativo Avançado como Polimento do Efluente Final
O estudo propõe a utilização de um processo oxidativo avançado (POA) com persulfato de sódio no esgoto sanitário proveniente da Estação de Tratamento de Esgoto (ETE) Parque Atheneu, Goiânia-GO. A partir de uma análise exploratória de dados, disponibilizados pela SANEAGO, foi possível observar um valor de demanda química de oxigênio (DQO) aceitável para descarte em mananciais com média de 325,22 mg L-1. Para demanda bioquímica de oxigênio (DBO), o valor médio do efluente tratado foi de 84,92 mg L-1, atingindo o exigido pela legislação. A aplicação de um POA como polimento final, poderia melhorar as características do esgoto sanitário lançado em mananciais.
- 27 August 2024
- Published by Revistas Processos Quimicos in Revista Processos Químicos
- Vol. 19 (36) , 29-33
Open AccessDesempenho Ambiental da ETE Parque Atheneu, Goiânia-GO: Verificação da Aplicabilidade de Processo Oxidativo Avançado como Polimento do Efluente Final
O estudo propõe a utilização de um processo oxidativo avançado (POA) com persulfato de sódio no esgoto sanitário proveniente da Estação de Tratamento de Esgoto (ETE) Parque Atheneu, Goiânia-GO. A partir de uma análise exploratória de dados, disponibilizados pela SANEAGO, foi possível observar um valor de demanda química de oxigênio (DQO) aceitável para descarte em mananciais com média de 325,22 mg L-1. Para demanda bioquímica de oxigênio (DBO), o valor médio do efluente tratado foi de 84,92 mg L-1, atingindo o exigido pela legislação. A aplicação de um POA como polimento final, poderia melhorar as características do esgoto sanitário lançado em mananciais.
- Open Access
- 27 August 2024
- Published by Revistas Processos Quimicos in Revista Processos Químicos
- Vol. 19 (36) , 91-96
Avaliação do Desempenho Ambiental da Estação de Tratamento de Esgoto Sanitário Samambaia - Localizada em Goiânia-GO
Este trabalho teve como objetivo à avaliação do desempenho ambiental da Estação de Tratamento de Esgoto sanitário, ETE Samambaia, em Goiânia-GO. A metodologia foi baseada em uma análise exploratória, conforme a disponibilização dos dados pela Companhia de Saneamento de Goiás S/A, referente aos anos de 2019 e 2020. A transformação dos dados em informações foi realizada a fim de possibilitar interpretações consistentes do desempenho ambiental da ETE. Para isso, utilizou-se um tratamento estatístico descritivo. Conclui-se que a ETE operou abaixo da sua capacidade de projeto, com desempenho satisfatório em relação aos limites médios de DBO no efluente final.
- 27 August 2024
- Published by Revistas Processos Quimicos in Revista Processos Químicos
- Vol. 19 (36) , 91-96
Open AccessAvaliação do Desempenho Ambiental da Estação de Tratamento de Esgoto Sanitário Samambaia - Localizada em Goiânia-GO
Este trabalho teve como objetivo à avaliação do desempenho ambiental da Estação de Tratamento de Esgoto sanitário, ETE Samambaia, em Goiânia-GO. A metodologia foi baseada em uma análise exploratória, conforme a disponibilização dos dados pela Companhia de Saneamento de Goiás S/A, referente aos anos de 2019 e 2020. A transformação dos dados em informações foi realizada a fim de possibilitar interpretações consistentes do desempenho ambiental da ETE. Para isso, utilizou-se um tratamento estatístico descritivo. Conclui-se que a ETE operou abaixo da sua capacidade de projeto, com desempenho satisfatório em relação aos limites médios de DBO no efluente final.
- 1 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Química Nova
- Vol. 47 (4)
MONITORAMENTO DE TRIHALOMETANOS (THMs) E DA QUALIDADE DA ÁGUA PARA ABASTECIMENTO PÚBLICO DA CIDADE DE CAVALCANTE, GOIÁS
- 1 January 2024
- Published by Sociedade Brasileira de Quimica (SBQ) in Química Nova
- Vol. 47 (4)
MONITORAMENTO DE TRIHALOMETANOS (THMs) E DA QUALIDADE DA ÁGUA PARA ABASTECIMENTO PÚBLICO DA CIDADE DE CAVALCANTE, GOIÁS
- 1 January 2023
- Published by Sociedade Brasileira de Quimica (SBQ) in Química Nova
- Vol. 46 (3) , 241-249
CARACTERIZAÇÃO DE RESÍDUOS SÓLIDOS INDUSTRIAIS POR ANÁLISE TÉRMICA: PERSPECTIVAS DE USO COMO MATERIAL FILTRANTE PARA ÁGUAS RESIDUÁRIAS
CHARACTERIZATION OF SOLID RESIDUES THROUGH THERMAL ANALYSIS: UTILIZATION PERSPECTIVE AS FILTER MATERIAL FOR WASTEWATER TREATMENT. Metallurgical waste and vermiculite are solid residues that have potential of utilization as filtering material. Nevertheless, they are commonly discarded. These materials have chemical sites like Si-O, Si-O-Si in vermiculite or have good ionic exchange properties like iron oxide compounds that can be used in adsorption processes. When these materials are combined with a synthetic blanket (OH, C=C, CO and C-H groups), it composes a filter layer with potential to be used in wastewater treatment. In this article, these materials were chemically treated and characterized by Thermogravimetry (TG), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR) and coupled TG-FTIR. The results suggest that organic compound contamination was not found after chemical treatment, which could have remained over the unity operations in the Metallurgical processes. The thermal and acid treatments influenced a major formation of iron oxide formation, but its oxidation degree (FeO, Fe2O3, or Fe2O3.FeO) were dependent on the sample granulometry. The Vermiculite shows an irreversible chemical modification after thermal treatment. The characterization of these residues shows its potential use as material in filter construction. Hence, it is fundamental to minimize the environmental impacts as well as to diminish the production costs in wastewater treatment.
- 1 January 2023
- Published by Sociedade Brasileira de Quimica (SBQ) in Química Nova
- Vol. 46 (3) , 241-249
CARACTERIZAÇÃO DE RESÍDUOS SÓLIDOS INDUSTRIAIS POR ANÁLISE TÉRMICA: PERSPECTIVAS DE USO COMO MATERIAL FILTRANTE PARA ÁGUAS RESIDUÁRIAS
CHARACTERIZATION OF SOLID RESIDUES THROUGH THERMAL ANALYSIS: UTILIZATION PERSPECTIVE AS FILTER MATERIAL FOR WASTEWATER TREATMENT. Metallurgical waste and vermiculite are solid residues that have potential of utilization as filtering material. Nevertheless, they are commonly discarded. These materials have chemical sites like Si-O, Si-O-Si in vermiculite or have good ionic exchange properties like iron oxide compounds that can be used in adsorption processes. When these materials are combined with a synthetic blanket (OH, C=C, CO and C-H groups), it composes a filter layer with potential to be used in wastewater treatment. In this article, these materials were chemically treated and characterized by Thermogravimetry (TG), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR) and coupled TG-FTIR. The results suggest that organic compound contamination was not found after chemical treatment, which could have remained over the unity operations in the Metallurgical processes. The thermal and acid treatments influenced a major formation of iron oxide formation, but its oxidation degree (FeO, Fe2O3, or Fe2O3.FeO) were dependent on the sample granulometry. The Vermiculite shows an irreversible chemical modification after thermal treatment. The characterization of these residues shows its potential use as material in filter construction. Hence, it is fundamental to minimize the environmental impacts as well as to diminish the production costs in wastewater treatment.
- Open Access
- 1 August 2022
- Published by Universidade Federal de Santa Maria in Revista Eletrônica em Gestão, Educação e Tecnologia Ambiental
- Vol. 24, e13
Cosmetic wastewater primary treatment by fenton process and final polishing adsorption
This work aimed to integrate two wastewater treatment technologies, Fenton process as the primary treatment and adsorption aiming achieve maximum removal efficiency and adequation to the environmental and water legislations. Wastewater from a cosmetics industry plant in the metropolitan area of Goiânia (Brazil) was the object of this research. It was analysed environmental parameters as absorbance, total iron, chemical oxygen demand, pH, total phenols, conductivity, H2O2, dissolved oxygen, turbidity, and total solids. They were analyzed in between processes at all stages. The effects of Fe2+ (18.42-257.89 mg L-1) and H2O2 (500-2300 mg L-1) concentrations and pH values (3.00-5.50) were studied for the Fenton process treatment. In adsorption, the activated carbon was characterized by infrared spectroscopy, elemental analysis, adsorption and desorption of N2 and thermogravimetry (TG/DTA). The effect of the contact time (4min-24h) and of the temperature variation in the system 20-60 °C were studied. By integrating the two technologies, a satisfactory removal rate was achieved for the analyzed parameters in the total time of treatment of 82 minutes
- 1 August 2022
- Published by Universidade Federal de Santa Maria in Revista Eletrônica em Gestão, Educação e Tecnologia Ambiental
- Vol. 24, e13
Open AccessCosmetic wastewater primary treatment by fenton process and final polishing adsorption
This work aimed to integrate two wastewater treatment technologies, Fenton process as the primary treatment and adsorption aiming achieve maximum removal efficiency and adequation to the environmental and water legislations. Wastewater from a cosmetics industry plant in the metropolitan area of Goiânia (Brazil) was the object of this research. It was analysed environmental parameters as absorbance, total iron, chemical oxygen demand, pH, total phenols, conductivity, H2O2, dissolved oxygen, turbidity, and total solids. They were analyzed in between processes at all stages. The effects of Fe2+ (18.42-257.89 mg L-1) and H2O2 (500-2300 mg L-1) concentrations and pH values (3.00-5.50) were studied for the Fenton process treatment. In adsorption, the activated carbon was characterized by infrared spectroscopy, elemental analysis, adsorption and desorption of N2 and thermogravimetry (TG/DTA). The effect of the contact time (4min-24h) and of the temperature variation in the system 20-60 °C were studied. By integrating the two technologies, a satisfactory removal rate was achieved for the analyzed parameters in the total time of treatment of 82 minutes
- Open Access
- 31 July 2021
- Published by Centro Universitario de Maringa in Revista em Agronegócio e Meio Ambiente
- Vol. 14 (4) , 1-15
Resíduos agroindustriais aplicados como material filtrante ao pós-tratamento de água residuária da produção de cosméticos
Este trabalho teve como objetivo o tratamento de águas residuárias, proveniente da indústria de cosméticos, para isso um filtro foi construído com camadas de resíduos agroindustriais (cascas de arroz, vermiculita e sabugo de milho carbonizado) em escala laboratorial. Com a filtração lenta, foi possível alcançar um valor final de (Demanda Química de Oxigênio) DQO na ordem de 255,98 mg O2 L-1 e turbidez final de 18,9 UNT valores estes que se enquadram nos valores dos parâmetros estaduais e federais exigidos para descarte em mananciais. Remoções de Carbono Orgânico Total (COT) de 54,84% e de fenóis totais de 68,78% foram importantes. Atenção também foi dada ao monitoramento da concentração de metais: cádmio, chumbo, níquel, cobalto, magnésio e manganês pós-filtração lenta. Os resultados alcançados foram promissores para o uso de resíduos agroindustriais como materiais filtrantes eficientes, de baixo custo e principalmente que proporcionam a sustentabilidade ambiental.
- 31 July 2021
- Published by Centro Universitario de Maringa in Revista em Agronegócio e Meio Ambiente
- Vol. 14 (4) , 1-15
Open AccessResíduos agroindustriais aplicados como material filtrante ao pós-tratamento de água residuária da produção de cosméticos
Este trabalho teve como objetivo o tratamento de águas residuárias, proveniente da indústria de cosméticos, para isso um filtro foi construído com camadas de resíduos agroindustriais (cascas de arroz, vermiculita e sabugo de milho carbonizado) em escala laboratorial. Com a filtração lenta, foi possível alcançar um valor final de (Demanda Química de Oxigênio) DQO na ordem de 255,98 mg O2 L-1 e turbidez final de 18,9 UNT valores estes que se enquadram nos valores dos parâmetros estaduais e federais exigidos para descarte em mananciais. Remoções de Carbono Orgânico Total (COT) de 54,84% e de fenóis totais de 68,78% foram importantes. Atenção também foi dada ao monitoramento da concentração de metais: cádmio, chumbo, níquel, cobalto, magnésio e manganês pós-filtração lenta. Os resultados alcançados foram promissores para o uso de resíduos agroindustriais como materiais filtrantes eficientes, de baixo custo e principalmente que proporcionam a sustentabilidade ambiental.
- 1 October 2020
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 8 (5)
The use of metallurgical waste for heterogeneous photo Fenton-Like treatment of cosmetic effluent
- 1 October 2020
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 8 (5)
The use of metallurgical waste for heterogeneous photo Fenton-Like treatment of cosmetic effluent
- Open Access
- 20 September 2018
- Published by Instituto de Pesquisas Ambientais em Bacias Hidrograficas (IPABHi) in Ambiente e Agua - An Interdisciplinary Journal of Applied Science
- Vol. 13 (5) , 1-21
Integration of treatment technologies with Fenton reagent for laboratory effluent remediation
This study investigated of the potential value of the integration of the coagulation/flocculation, Advanced Oxidation Processes (AOP) (Fenton reagent) and slow sand filtration technologies, with the aim of treating laboratory wastewater. The treatment system was designed in laboratory scale through coagulation/flocculation. It involved the use of Jar Test equipment with a sequence of two rotational phases: fast mixes to 300 rpm for 20 seconds and slow mixes to 30 rpm for 6 minutes and 10 seconds, with the addition of anionic polymer and sedimentation for 60 minutes at ambient temperature. In the treatment via Fenton reagent, two rotational phases were used: rapid mixing at 300 rpm for 20 seconds with the addition of iron (Fe2+) and slow mixing at 30 rpm for 6 minutes and 10 seconds with the addition of hydrogen peroxide, followed by 60 minutes of sedimentation at ambient temperature. A cylindrical tank of polyvinyl chloride, sands and non-woven synthetic fabrics were used in the slow filtration. The filtration rate adopted was 3 m3 m-2 d-1 with a hydraulic retention time of 264 minutes. The best concentrations of chemical reagents used in the treatments were: 0.80 mg L-1 of polymeric anionic, 200.00 mg L-1 of H2O2 and 13.00 mg L-1 of total soluble iron. The integration of the treatment technologies made it possible to achieve a removal rate of 75.27% of COD and 94.12% of total phenols. Furthermore, the conjugation of the processes allowed the removal of 87.58% of TOC.
- 20 September 2018
- Published by Instituto de Pesquisas Ambientais em Bacias Hidrograficas (IPABHi) in Ambiente e Agua - An Interdisciplinary Journal of Applied Science
- Vol. 13 (5) , 1-21
Open AccessIntegration of treatment technologies with Fenton reagent for laboratory effluent remediation
This study investigated of the potential value of the integration of the coagulation/flocculation, Advanced Oxidation Processes (AOP) (Fenton reagent) and slow sand filtration technologies, with the aim of treating laboratory wastewater. The treatment system was designed in laboratory scale through coagulation/flocculation. It involved the use of Jar Test equipment with a sequence of two rotational phases: fast mixes to 300 rpm for 20 seconds and slow mixes to 30 rpm for 6 minutes and 10 seconds, with the addition of anionic polymer and sedimentation for 60 minutes at ambient temperature. In the treatment via Fenton reagent, two rotational phases were used: rapid mixing at 300 rpm for 20 seconds with the addition of iron (Fe2+) and slow mixing at 30 rpm for 6 minutes and 10 seconds with the addition of hydrogen peroxide, followed by 60 minutes of sedimentation at ambient temperature. A cylindrical tank of polyvinyl chloride, sands and non-woven synthetic fabrics were used in the slow filtration. The filtration rate adopted was 3 m3 m-2 d-1 with a hydraulic retention time of 264 minutes. The best concentrations of chemical reagents used in the treatments were: 0.80 mg L-1 of polymeric anionic, 200.00 mg L-1 of H2O2 and 13.00 mg L-1 of total soluble iron. The integration of the treatment technologies made it possible to achieve a removal rate of 75.27% of COD and 94.12% of total phenols. Furthermore, the conjugation of the processes allowed the removal of 87.58% of TOC.
- 6 September 2018
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 41 (3) , 221-230
Treatment of Real Cosmetic Effluent Resulting from the Manufacture of Hair Conditioners by Reduction Degradation, Adsorption and the Fenton Reaction
The objective of this study was to investigate the pollutant matrix for the manufacture of hair conditioners, by combining the treatment systems through reductive degradation/adsorption with assisted Fenton reaction. The procedure involved using 0.20g of metallic iron in the form of steel wool (medium coarse), with effluent in pH 3.0 for reductive degradation/adsorption and for Fenton reaction was used Hydrogen peroxide was used in 220 mg L−1, for a total period of 18 min. There was a rate of 84.55% for the chemical oxygen demand and 17.93% for turbidity. The techniques employed were useful since the composition is diverse, with a high organic and non-biodegradable load.
- 6 September 2018
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 41 (3) , 221-230
Treatment of Real Cosmetic Effluent Resulting from the Manufacture of Hair Conditioners by Reduction Degradation, Adsorption and the Fenton Reaction
The objective of this study was to investigate the pollutant matrix for the manufacture of hair conditioners, by combining the treatment systems through reductive degradation/adsorption with assisted Fenton reaction. The procedure involved using 0.20g of metallic iron in the form of steel wool (medium coarse), with effluent in pH 3.0 for reductive degradation/adsorption and for Fenton reaction was used Hydrogen peroxide was used in 220 mg L−1, for a total period of 18 min. There was a rate of 84.55% for the chemical oxygen demand and 17.93% for turbidity. The techniques employed were useful since the composition is diverse, with a high organic and non-biodegradable load.