KSKiho Seong

Kiho Seong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kiho Seong has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Real-Time End-to-End Event-Based Tactile Sensing System

    by Yuncheng Lu, Kiho Seong, Si En Ng, Shibi Varku, Arindam Basu, Nripan Mathews, Tony Tae-Hyoung Kim

    Event-based tactile sensing offers a promising alternative to frame-based approaches by reducing data redundancy, yet existing systems often lack end-to-end hardware support and remain power-inefficient. This work presents an energy-efficient event-based tactile sensing system that codesigns algorithms and hardware for real-time perception. At the front end, a leakage-compensated event-driven readout circuit integrates multiple tactile sensors into a single node, minimizing wiring and static power. At the algorithm level, a 2-D convolutional neural network (CNN) reconstructs event frames for handwritten digit recognition with strong robustness to varying interaction durations, while a graph neural network (GNN) processes irregular tactile layouts for object classification. A customized event-based tactile processor (ETP) supports end-to-end tactile processing, incorporating a dual-mode event frame builder (EFB) and a neural network processing unit (NPU) with an optimized data-reuse scheme. Evaluated using 28-nm CMOS, the ASIC performs handwritten digit recognition and object classification in 0.44 and 0.37 ms, respectively. The system consumes the total power of 5.2 mW with only 0.11-mW dynamic power, demonstrating an efficient solution for always-on tactile perception.

  • Open Access

    8T-SRAM Based Process-In-Memory (PIM) System With Current Mirror for Accurate MAC Operation

    by Keun-Yong Chung, Honggu Kim, Yerim An, Kiho Seong, Dong-Hyun Shin, Kwang-Hyun Baek, Yong Shim

    Process-in-memory (PIM) is an emerging computing paradigm to overcome the energy bottleneck inherent in conventional computing platform. While PIM utilizes several types of memory elements, SRAM based PIM has been researched extensively for its high scalability and feasibility by using CMOS process technology. In this work, we proposed 8T SRAM based process-in-memory system with current mirror for accurate MAC operation. To resolve the nonlinearity issue inherent in current-based SRAM MAC macro, we utilized cascaded current mirror. Furthermore, to enable more precise MAC operation, we allocated RWL timing pulses which drive 8T SRAM bitcells in the middle of timing duration. Our PIM architecture realize 4 bit input, 4 bit weight and 4 bit output precisions. Prototype chip has been fabricated using TSMC 65nm GP process technology. Measurement result has proved the MAC operation linearity of designed 8T SRAM based PIM system, and its throughput and energy efficiency with 0.29 GOPs and 1.05 TOPs/W. Software level analysis proved that our design can achieve upto 98.02 percent accuracy for MNIST dataset classification and 94.93 percent accuracy for CIFAR-10 dataset classification.


  • A 2.5 GS/s 7-Bit 5-Way Time-Interleaved SAR ADC With On-Chip Background Offset and Timing-Skew Calibration

    by Kiho Seong, Jae-Soub Han, Yong Shim, Kwang-Hyun Baek

    This brief presents the on-chip background offset and timing-skew calibration of the 1-then-2b/cycle time-interleaved successive-approximation-register analog-to-digital converter (TI SAR ADC). For timing-skew between sub-ADC’s sampling clocks, a comparator offset-based window detector (WD) is used to adjust the clock edge misalignment. In addition, comparator offset calibration is considered both in terms of 1) global offset (between the offset-free reference comparator and the local reference comparator in each sub-ADC) and 2) local offset (between the local reference comparator and the rest of the comparators in the same sub-ADC). The proposed calibration sufficiently suppresses noise floor and spurs, and all calibrations are performed in the background without interfering with normal ADC operation. The prototype 5-way TI SAR ADC is fabricated in a 28 nm CMOS process and occupies a 0.03 mm2 area including on-chip calibration. With the proposed calibration, the prototype achieves SNDR of 40 dB at Nyquist input and consumes 7.57 mW, leading to the Walden figure of merit ( ${\text {FoM}_{W}}$ ) of 37.2 fJ/conversion-step.


  • A 3.2-GHz 178-fsrms Jitter Subsampling PLL/DLL-Based Injection-Locked Clock Multiplier

    by Dong-Hyun Yoon, Dong-Kyu Jung, Kiho Seong, Jae-Soub Han, Keun-Yong Chung, Ju-Eon Kim, Tony Tae-Hyoung Kim, Kwang-Hyun Baek

    This article proposes a 3.2-GHz subsampling phase-locked loop (SSPLL)-based injection-locked clock multiplier (ILCM) using a subsampling delay-locked loop (SSDLL). The proposed ILCM achieves a superior noise reduction effect at low offset frequency because of the high feedback gain of SSPLL. Also, SSDLL is proposed for background phase calibration between SSPLL and injection. Since SSPLL and SSDLL use identical SSCP, the power consumption of the frequency and phase calibration is only 1.32 mW. This work is fabricated in a 65-nm CMOS process, and the 10-kHz phase noise is improved by 8.6 dB. The rms jitter from 10 kHz to 30 MHz is 178 fs. The chip-to-chip variations (20 chips) are 17 and 169 fs with/without SSDLL, respectively. The measured results show that FoM 1 , FoM 2 , and total power consumption are −245.1, −260.1 dB, and 9.85 mW, respectively.


  • A 0.5 V 10 b 3 MS/s 2-Then-1b/Cycle SAR ADC With Digital-Based Time-Domain Reference and Dual-Mode Comparator

    by Dong-Kyu Jung, Kiho Seong, Jae-Soub Han, Yong Shim, Kwang-Hyun Baek

    This brief presents a low-power asynchronous 10-bit 2-then-1b/cycle successive approximation register (SAR) analog-to-digital converter (ADC). With partial adoption of 2b/cycle mode only for higher-order bit conversions, additional area and power consumption could be minimized while maintaining fast conversion rate. Moreover, unlike the previous 2b/cycle conversion architecture, where two capacitive digital-to-analog converters (C-DACs) and multiple analog comparators are unavoidable, the proposed 2-then-1b/cycle conversion is implemented with only one C-DAC and one analog comparator by utilizing a digital-based time-domain reference. The speed of 1b/cycle conversion for lower-order bits is improved with a dual-mode comparator. With the aforementioned techniques, the prototype 10-bit SAR ADC is fabricated in 65 nm CMOS process. The ADC core occupies an active area of 0.0142 mm 2 and consumes power of 3.8 $\boldsymbol{\mu }\text{W}$ at 0.5 V supply voltage and 3 MS/s conversion rate. The SNDR measured at a Nyquist-rate input frequency is 56.41 dB, resulting in a figure of merit (FoM) is 2.33 fJ/c.-s.


  • Open Access

    A 0.5 V 8–12 Bit 300 KSPS SAR ADC With Adaptive Conversion Time Detection-and-Control for High Immunity to PVT Variations

    by Ju Eon Kim, Taegeun Yoo, Dong-Kyu Jung, Dong-Hyun Yoon, Kiho Seong, Tony Tae-Hyoung Kim, Kwang-Hyun Baek

    In this paper, a low power asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) involving the process, voltage, and temperature (PVT) compensation is presented. A proposed adaptive conversion time detection-and-control technique enhances the power efficiency, covering wide PVT variations. The proposed detection-and-control technique senses PVT variation in an aspect of conversion time, and adaptively controls the operation speed and power consumption. For PVT compensation, the proposed architecture includes the local supply/ground voltage. The local supply/ground voltage makes high |VGS| for transistors in the comparator and capacitive digital-to-analog converter switches, resulting in enhanced operation speed. However, when PVT condition changes to be favorable for the conversion speed, the |VGS| decreases for low power consumption. 30 chips were measured to verify the proposed ADC. Having the proposed architecture tested with 10 kHz input frequency, SNDR remained higher than 60 dB at unfavorable conditions such as -9 % supply voltage variation, or -20 ⁰C temperature variation. On the other hand, at favorable conditions such as +9 % supply voltage variation, or 80 ⁰C temperature variation, the power consumption of SAR ADC decreased without performance degradation.


  • Open Access

    Design and Analysis of Low Power and High SFDR Direct Digital Frequency Synthesizer

    by Ji-Min Choi, Dong-Hyun Yoon, Dong-Kyu Jung, Kiho Seong, Jae-Soub Han, Woojoo Lee, Kwang-Hyun Baek

    Due to the advantages of fast frequency shifting, continuous phase shifting, fine frequency resolution, large bandwidth, and excellent spectral purity, the direct digital frequency synthesis (DDFS) technique is attracting more attention than ever before. Although the DDFS suffer from high power consumption, recent researches on the development of the low power DDFS (LP-DDFS) increases the feasibility of applying the DDFS to portable devices. To further accelerate the use of LP-DDFS, a new LP-DDFS design to significantly improve power efficiency is proposed and analyzed in this paper. In the new design, the dominant spur by truncation errors causing performance degradation has been also thoroughly considered. Since the existing dithering techniques for the truncation error problems can cause the additional performance degradation due to the side effects such as frequency offset and SNDR deterioration, an enhanced dithering technique is also proposed in this paper. The proposed technique includes a frequency compensation circuit and thus minimizes the truncation errors in the LP-DDFS with the minimal additional power consumption and SNDR degradation. Both theoretical and experimental analysis are conducted to verify the proposed design, where a prototype chip is fabricated and measured.