Zhenliang Zhou

When the tunnel boring machine (TBM) construction method is used to build tunnels, if the type of TBM is not appropriate, problems, such as low construction efficiency and increased construction cost, will easily occur. Therefore, it is necessary to build a TBM selection decision-making model to guide TBM selection. In this paper, seven evaluation indexes are selected according to engineering experience and expert suggestions, and the quantitative standards of each index are unified. The modified analytic hierarchy process (MAHP) method is used to determine the weight of each evaluation index. The technique for order preference by similarity to an ideal solution (TOPSIS) method is adopted as the decision-making method of TBM selection. Finally, a TBM selection decision-making model is proposed based on the above methods. In order to verify the reliability of the TBM selection decision-making model proposed in this paper, we selected three projects for case verification and compared them with the previous TBM selection methods. The results show that the decision-making results of the method proposed in this paper are good. Additionally, the method proposed in this paper is more comprehensive and accurate than the previous methods. The model proposed in this paper can provide better suggestions for TBM selection in the project planning stage.

When a TBM carries out tunnelling in complex strata, there is often low tunnelling efficiency and an increase in tunnelling costs due to the improper selection of tunnelling parameters, the wrong estimation of geological conditions, or adverse geology, so it is necessary to evaluate the tunnelling adaptability of TBM construction. In this paper, based on hydraulic engineering in Xinjiang, 11 evaluation indexes of TBM tunnelling adaptability are determined by comprehensively considering the influence of tunnelling parameters, geological conditions, and adverse geological factors on TBM tunnelling adaptability. After that, the membership function of each evaluation index is determined by referring to the existing research results and fuzzy mathematics method, and the weight of each evaluation index is determined and adjusted by the analytic hierarchy process (AHP)–entropy weight (EW) method. Finally, the adaptability evaluation method and evaluation model of TBM tunnelling are put forward. The TBM tunnelling adaptability evaluation model proposed in this paper is verified by relying on the actual situation of three interval tunnels in the project, and good effects are obtained. This study can provide a reference for the evaluation of TBM tunnelling adaptability in similar strata.

Bifurcated tunnels have two major engineering problems of large span and small interval simultaneously, and they pose higher demands on design and construction technology. The Liantang tunnel has a maximum span of 30.1 m, a minimum interval of only 1.05 m and a single excavation face; the existing construction method cannot meet the demand. Based on these features, this paper proposes a reverse expanding excavation method and a stepwise controlled blasting excavation method. By numerical calculation and field testing, the stability and mechanical characteristics of the surrounding rock and primary support using the two methods were researched. The results show that the reverse expanding excavation method, by excavating the pilot tunnel first and then reversely excavating the remaining part, achieves stepwise excavation of the super-large-span tunnel, provides mechanised working conditions and avoids multiple conversions of the excavation method. The stepwise controlled blasting excavation method, by grouting and reinforcing the shared rock first, and then controlled blasting of the later tunnel in steps, ensures the stability of the shared rock, reduces the construction influence of the later tunnel on the existing tunnel and omits the construction of a mid-partition. This study can provide a reference for future similar projects.

With the orderly promotion of the infrastructure construction in China, the number of coastal tunnels is increasing, but the coastal environment is accompanied by a large amount of groundwater and the designs of the waterproof and drainage system of coastal tunnels have always been a hot topic in the industry. If the waterproof and drainage system designs of the coastal tunnels are improper, the tunnel structure will easily be damaged and the stability and service life of the whole project will be affected. Based on the Gongbei tunnel project of the Hong Kong‐Zhuhai‐Macao Bridge, this paper discusses the designs of the waterproof and drainage system, and the waterproof detail structures of the Gongbei tunnel. Indoor similarity tests were carried out to study the law of the free water discharge of the tunnel under variable water heads, the relationship between the water pressure outside the lining and the water discharge, the relationship between the water pressure outside the pipe roof and the water discharge, and the distribution of water pressure around the tunnel. The reliability of the indoor similarity test was verified by the field test. The results show that the whole waterproof system should be adopted in the Gongbei tunnel, that is, grouting ring + pipe roof freezing ring + initial lining + waterproof board + tertiary lining. In a certain range, the greater the water head, the greater the free water discharge of the tunnel. When the water head is large, the free drainage tends to a fixed value. When the tunnel is completely plugged, the water pressure outside the tunnel is distributed from the hydrostatic pressure. When the tunnel adopts drainage measures, the water pressure outside the lining will be reduced to a certain extent even the water discharge is very small. The above research can provide a reference for the design of the waterproof and drainage system similar to the coastal tunnel in the future.

The water around thenear-sea tunnels is supplied infinitely, and mechanical characteristics of the lining and movement joint are inevitably affected by waterproof methods. The research on the mechanical characteristics of the waterproof system is immature. As a case study of the Gongbei tunnel, a scale model was established in this study, and the stratum, pipe curtain, grouting circle, lining, waterproof board, and movement joint were simulated based on the similarity theories. By changing the externally applied water pressure and drainage discharge, the variation and distribution of the water pressure and strain on the lining with the fully wrapped waterproof (FWW) method, the lining with the partially wrapped waterproof (PWW) method, and the movement joint were investigated. Furthermore, several suggestions on the selection of the waterproof method were presented. The results indicate that the PWW method can reduce the water pressure and strain on the lining under the drained state. Under the state of free drainage, the strain on the lining with the PWW method may get a discount of about 30%. More attention could be paid to the waterproof of the movement joints in the construction process, especially the invert. The research results may offer some valuable insights into the waterproof design of similar near-sea tunnels.

As a common method applied in the construction of tunnels with Grade IV and Grade V surrounding rock, the center diaphragm (CD) method has the advantage of resisting the inward horizontal convergence of the tunnel. However, due to the small lateral earth pressure of the shallow tunnel, the curved center diaphragm would have an unstable stress state and cannot provide sufficient support to the surrounding rock. Based on the CD method, this study presents a vertical center diaphragm (VCD) method with an axisymmetric structure. The application condition of the VCD method relies on the comparison of the surface settlement and tunnel deformation with the two methods in different surrounding rock grades and buried depths by using a three-dimensional finite-difference code. Based on the Shenzhen Eastern Transit Expressway Connection Line Tunnel, which has six lanes of double lines, the deformation regularities and mechanical characteristics of the VCD method, including the surface settlement, tunnel deformation, internal force of the center diaphragm, surrounding rock pressure, and steel arch stress, are investigated by numerical calculations and a field comparative test. The results obtained in this study provide several suggestions for constructing shallow tunnels. Furthermore, the construction efficiency and economy of the VCD method are evaluated.

We present a novel silicon photomultiplier based on a shallow junction obtained within a standard 0.35 ${\mu }\text{m}$ complementary metal oxide semiconductor process. The sensitive structure is equipped with a dedicated optical window as well as an optimized antireflective coating. The device exhibits performances comparable to custom-based commercial technologies: an unprecedented photon detection efficiency of 43% at 420 nm, a breakdown voltage temperature dependence of (27.9 ± 0.9) mV/K, a dark count rate of 480 kHz/mm ² , a gain of ${3\times 10^{6}}$ , and a single photon time resolution of (78 ± 2) ps (FWHM). The process proposed in this letter can be applied to new generation single photon sensors with on-chip integrated intelligent electronics.