Alexander Petrovich Svintsov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander Petrovich Svintsov has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Makhmud Kharun
Department of Reinforced Concrete and Stone Structures, Moscow State University of Civil Engineering, 26 Yaroslavskoye Highway, 129337 Moscow, Russia
5 shared publications Vera V. Galishnikova
4 shared publications- Abbas Abdulhussein Abd Noor
Civil Engineering Department, Al-Muthanna University, Samawah 66001, Al-Muthanna, Iraq
2 shared publications Nadezhda А. Stashevskaya
Peoples' Friendship University of Russia (RUDN University), 6 Miklukho-Maklaya Street, Moscow, 117198, Russian Federation
2 shared publicationsNikolay Alexandrovich Konoplev
2 shared publications- Roman Fediuk
Far Eastern Federal University, Vladivostok, Russia
2 shared publications
Latest Publications
- 18 February 2023
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 24 (6) , 1711-1730
Assessment of the reliability of the system for the erection of buildings from blocks of retained formwork of cement-particle boards
- 18 February 2023
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 24 (6) , 1711-1730
Assessment of the reliability of the system for the erection of buildings from blocks of retained formwork of cement-particle boards
- Open Access
Removing Pollutants from Sewage Waters with Ground Apricot Kernel Shell Material
For the first time, a comprehensive review of the literature data on the use of apricot (Prunus armeniaca) biomass components as a sorption material for the treatment of wastewater and environmental water from various pollutants is carried out in the present study. In addition to a comprehensive analysis of contemporary studies, the current work carried out its own microstructural and energy dispersive studies. It shows that apricot kernel shell is a promising raw material for obtaining sorption materials that can be used to extract various pollutants from aqueous media. The parameters of sorption interaction are presented, at which the highest rate of removal of pollutants was achieved. It is shown that the sorption capacity of apricot biomass components can be increased by modifying it with various chemical reagents, as well as other physical and physicochemical methods. We reveal that most publications consider the use of the latter as a raw material for the production of activated carbons. It is established that the surface area and total pore space of activated carbons from apricot kernel shells depend on the modes of carbonization and activation. It is shown that activated carbons are effective adsorbents for removing various pollutants (metal ions, dyes, oil and oil products) from aqueous media. It was found that the adsorption isotherms of pollutants in most cases are best described by the Langmuir and Freundlich models, and the process kinetics is most often described by the pseudo-second-order model. The possibility of improving the sorption characteristics of apricot biomass during chemical or physicochemical treatment is also shown.
Open AccessRemoving Pollutants from Sewage Waters with Ground Apricot Kernel Shell Material
For the first time, a comprehensive review of the literature data on the use of apricot (Prunus armeniaca) biomass components as a sorption material for the treatment of wastewater and environmental water from various pollutants is carried out in the present study. In addition to a comprehensive analysis of contemporary studies, the current work carried out its own microstructural and energy dispersive studies. It shows that apricot kernel shell is a promising raw material for obtaining sorption materials that can be used to extract various pollutants from aqueous media. The parameters of sorption interaction are presented, at which the highest rate of removal of pollutants was achieved. It is shown that the sorption capacity of apricot biomass components can be increased by modifying it with various chemical reagents, as well as other physical and physicochemical methods. We reveal that most publications consider the use of the latter as a raw material for the production of activated carbons. It is established that the surface area and total pore space of activated carbons from apricot kernel shells depend on the modes of carbonization and activation. It is shown that activated carbons are effective adsorbents for removing various pollutants (metal ions, dyes, oil and oil products) from aqueous media. It was found that the adsorption isotherms of pollutants in most cases are best described by the Langmuir and Freundlich models, and the process kinetics is most often described by the pseudo-second-order model. The possibility of improving the sorption characteristics of apricot biomass during chemical or physicochemical treatment is also shown.
- 6 February 2022
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 23 (2) , 187-201
Evaluation of the reliability of the erection of brick walls structures of low-rise residential buildings
- 6 February 2022
- Published by Springer Nature in Asian Journal of Civil Engineering
- Vol. 23 (2) , 187-201
Evaluation of the reliability of the erection of brick walls structures of low-rise residential buildings
- Open Access
- 30 December 2021
- Published by Peoples' Friendship University of Russia in Structural Mechanics of Engineering Constructions and Buildings
- Vol. 17 (5) , 528-537
Thermal processing of fresh concrete with infrared radiation
Currently, the construction of buildings made of monolithic concrete and reinforced concrete is becoming increasingly relevant. The use of innovative technologies, minimum construction time, durability, reliability, the ability to perform work in various climatic conditions, architectural individuality contribute to the development of monolithic construction. Concrete and reinforced concrete are the main materials of modern construction. The quality of structures depends not only on the composition of concrete, the amount of portland cement, the chemical additives used, the water-cement ratio, the quality of fillers, etc., but also significantly on the heat and humidity regime of concrete holding. To ensure the necessary temperature conditions for hardening and strength gain of concrete, various methods of heating structures are used. One of the methods of concrete care is thermal processing during the hardening period and the acquisition of critical or design strength. The aim of the study is to improve the technology of erection of monolithic concrete and reinforced concrete structures using thermal processing of concrete by means of infrared radiation. The technology of thermal processing of the laid and compacted concrete mixture using infrared heating and a two-chamber transparent shelter for infrared rays has been developed. The obtained results permit us to provide conditions for the normal course of the chemical reaction of hydration, hardening and strength gain. This allows successfully solve the problems of concreting in the erection of buildings and structures made of monolithic concrete and reinforced concrete.
- 30 December 2021
- Published by Peoples' Friendship University of Russia in Structural Mechanics of Engineering Constructions and Buildings
- Vol. 17 (5) , 528-537
Open AccessThermal processing of fresh concrete with infrared radiation
Currently, the construction of buildings made of monolithic concrete and reinforced concrete is becoming increasingly relevant. The use of innovative technologies, minimum construction time, durability, reliability, the ability to perform work in various climatic conditions, architectural individuality contribute to the development of monolithic construction. Concrete and reinforced concrete are the main materials of modern construction. The quality of structures depends not only on the composition of concrete, the amount of portland cement, the chemical additives used, the water-cement ratio, the quality of fillers, etc., but also significantly on the heat and humidity regime of concrete holding. To ensure the necessary temperature conditions for hardening and strength gain of concrete, various methods of heating structures are used. One of the methods of concrete care is thermal processing during the hardening period and the acquisition of critical or design strength. The aim of the study is to improve the technology of erection of monolithic concrete and reinforced concrete structures using thermal processing of concrete by means of infrared radiation. The technology of thermal processing of the laid and compacted concrete mixture using infrared heating and a two-chamber transparent shelter for infrared rays has been developed. The obtained results permit us to provide conditions for the normal course of the chemical reaction of hydration, hardening and strength gain. This allows successfully solve the problems of concreting in the erection of buildings and structures made of monolithic concrete and reinforced concrete.
- Open Access
- 28 May 2021
- Published by EDP Sciences
- Vol. 263, 04010
Reliability of water fittings in operating conditions
Water fittings are an integral part of the internal water supply system. The reliability of their work under operating conditions largely influence on the continuity of water supply to the population. The reliability indicators of sanitary fittings allow the services responsible for the technical condition of the indoor water supply of houses to pay priority attention to the factors that determine the uninterrupted water supply of the population and reduce the loss of drinking water. In this study, the results of indicators of operational reliability of faucets for sinks in kitchens and washbasins in toilet rooms of apartments of multi-store residential buildings in a residential neighborhood are presented. The study was performed based on the analysis of records in the logs of data on valve failures for 2016-2018. The main malfunctions are established, the random coincidence of which leads to failures. The reliability of sanitary fittings is affected not only by their structure and the characteristics of the materials, as well as by the exploitation conditions. The probability of failure-free operation of sanitary fittings in exploitation conditions for a time not exceeding the duration of the reduction of water supply to consumers in residential buildings is the basic parameter of its reliability.
- 28 May 2021
- Published by EDP Sciences
- Vol. 263, 04010
Open AccessReliability of water fittings in operating conditions
Water fittings are an integral part of the internal water supply system. The reliability of their work under operating conditions largely influence on the continuity of water supply to the population. The reliability indicators of sanitary fittings allow the services responsible for the technical condition of the indoor water supply of houses to pay priority attention to the factors that determine the uninterrupted water supply of the population and reduce the loss of drinking water. In this study, the results of indicators of operational reliability of faucets for sinks in kitchens and washbasins in toilet rooms of apartments of multi-store residential buildings in a residential neighborhood are presented. The study was performed based on the analysis of records in the logs of data on valve failures for 2016-2018. The main malfunctions are established, the random coincidence of which leads to failures. The reliability of sanitary fittings is affected not only by their structure and the characteristics of the materials, as well as by the exploitation conditions. The probability of failure-free operation of sanitary fittings in exploitation conditions for a time not exceeding the duration of the reduction of water supply to consumers in residential buildings is the basic parameter of its reliability.
- Open Access
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1687 (1) , 012035
Planning an experimental study of water valves
Designing the plan of the experiment represents the optimal control of empirical research while processing an incomplete knowledge of the mechanism of phenomena. Experiments are usually performed in small series according to a pre-compiled algorithm, optimal in a pre-defined range. After each series of experiments, the measurement results are processed and an informed decision is made. Statistical processing of experiment data allows us to get the correct research results with errors that do not exceed the tolerance limits. The research goal is to develop a program and plan for the experimental study of the laws and quantitative values of the hydraulic characteristics of water folding valves. As a result of the research, attention is emphasized on the preliminary processing of the experiment data provided for the design of the experiment to study the hydraulic characteristics of the valves. As a part of the research of the experiment design, a program for the experimental change in water flow through the passage opening of the water valves was developed and verified. The results of the research allow us to carry out experimental studies of the hydraulic characteristics of the valves and obtain data with a given statistical security.
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1687 (1) , 012035
Open AccessPlanning an experimental study of water valves
Designing the plan of the experiment represents the optimal control of empirical research while processing an incomplete knowledge of the mechanism of phenomena. Experiments are usually performed in small series according to a pre-compiled algorithm, optimal in a pre-defined range. After each series of experiments, the measurement results are processed and an informed decision is made. Statistical processing of experiment data allows us to get the correct research results with errors that do not exceed the tolerance limits. The research goal is to develop a program and plan for the experimental study of the laws and quantitative values of the hydraulic characteristics of water folding valves. As a result of the research, attention is emphasized on the preliminary processing of the experiment data provided for the design of the experiment to study the hydraulic characteristics of the valves. As a part of the research of the experiment design, a program for the experimental change in water flow through the passage opening of the water valves was developed and verified. The results of the research allow us to carry out experimental studies of the hydraulic characteristics of the valves and obtain data with a given statistical security.
- Open Access
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1687 (1) , 012016
Planning of an experimental research of the organization of townhouses’ construction
One of the most important ways in improving the research’s efficiency is an experiment’s planning. The aim of the study is to identify and study various factors that can affect the productivity of brick layers during bricklaying of townhouses in Iraq. Visual observation, timing and photographs of the working day were carried out during eight working weeks. In the process of daily monitoring, causal relationships of the formation of downtime and overtime work of bricklayers were identified. The most significant factors are untimely delivery of materials and alteration of performed work. The data obtained are the basis for the development of a mathematical model of labor productivity indicators. An analysis of the data on the functioning of the construction technological system for erecting brick walls of buildings shows that its states can be modeled by regular Markov processes. The data obtained are the basis for the development of a mathematical model of labor productivity indicators.
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1687 (1) , 012016
Open AccessPlanning of an experimental research of the organization of townhouses’ construction
One of the most important ways in improving the research’s efficiency is an experiment’s planning. The aim of the study is to identify and study various factors that can affect the productivity of brick layers during bricklaying of townhouses in Iraq. Visual observation, timing and photographs of the working day were carried out during eight working weeks. In the process of daily monitoring, causal relationships of the formation of downtime and overtime work of bricklayers were identified. The most significant factors are untimely delivery of materials and alteration of performed work. The data obtained are the basis for the development of a mathematical model of labor productivity indicators. An analysis of the data on the functioning of the construction technological system for erecting brick walls of buildings shows that its states can be modeled by regular Markov processes. The data obtained are the basis for the development of a mathematical model of labor productivity indicators.
- 1 September 2020
- Published by Elsevier in Journal of Building Engineering
- Vol. 31
Monitoring of heating systems as a factor of energy safety of buildings
- 1 September 2020
- Published by Elsevier in Journal of Building Engineering
- Vol. 31
Monitoring of heating systems as a factor of energy safety of buildings
- Open Access
- 1 August 2020
- Published by Elsevier in Data in Brief
- Vol. 31, 105756
Dataset on the effect of nano-modified additives of concrete mixes technological properties for winter concreting
- 1 August 2020
- Published by Elsevier in Data in Brief
- Vol. 31, 105756
Open AccessDataset on the effect of nano-modified additives of concrete mixes technological properties for winter concreting
- Open Access
- 1 August 2020
- Published by Elsevier in Data in Brief
- Vol. 31, 105730
Dataset for assessing the reliability of central heating station based units of buildings
- 1 August 2020
- Published by Elsevier in Data in Brief
- Vol. 31, 105730
Open AccessDataset for assessing the reliability of central heating station based units of buildings