Karsten Woll
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Karsten Woll has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Alex H. Kinsey
Department of Materials Science and Engineering, Johns Hopkins University, Baltimore, USA
2 shared publications - Gemma Tinti
INFN, Laboratori Nazionali di Frascati
2 shared publications - John David Gibbins
Department of Materials Science and Engineering, Johns Hopkins University, Baltimore, MD 21218, USA
2 shared publications M. Stüber
2 shared publications- Timothy P. Weihs
Johns Hopkins University
2 shared publications - Andreas Rosenkranz
Department of Chemical Engineering, Biotechnology and Materials, FCFM, University of Chile, Santiago, Chile
1 shared publication
Latest Publications
- Open Access
Impact of Microstructure of Nanoscale Magnetron Sputtered Ru/Al Multilayers on Thermally Induced Phase Formation
In this study, we report on phase formation and microstructure evolution in multiscale magnetron sputtered Ru/Al multilayers upon thermal annealing in vacuum at slow heating rates of 10 K/min. By specifically adjusting the microstructure and design of the as-deposited multilayers, the formation of certain desired phases can be tuned. We demonstrate that the synthesis of single phase RuAl thin films is possible in a very controlled manner in a solid state only via thermal activation without initiating the self-propagating exothermic reactions of Ru/Al multilayers. To investigate phase formation sequences and the resulting microstructures, Ru/Al multilayers were designed via magnetron sputtering with systematic variation of bilayer modulation periods and subsequent vacuum annealing. Thin films samples were characterized by in situ high-temperature XRD, TEM imaging and diffraction. It is shown that different phase sequences appear in strong correlation with the modulation length. Depending on the multilayer design, the phase formation toward single-phase RuAl thin films happens as either a multi-step or single-step event. In particular, below a critical threshold of the modulation period, the multi-step phase formation can be suppressed, and only the desired RuAl target phase is obtained with a pronounced growth in a preferred orientation. This finding may be versatile for the targeted synthesis of intermetallic phases, contributing to further understanding of phase formation in such nanoscale multilayer systems.
Open AccessImpact of Microstructure of Nanoscale Magnetron Sputtered Ru/Al Multilayers on Thermally Induced Phase Formation
In this study, we report on phase formation and microstructure evolution in multiscale magnetron sputtered Ru/Al multilayers upon thermal annealing in vacuum at slow heating rates of 10 K/min. By specifically adjusting the microstructure and design of the as-deposited multilayers, the formation of certain desired phases can be tuned. We demonstrate that the synthesis of single phase RuAl thin films is possible in a very controlled manner in a solid state only via thermal activation without initiating the self-propagating exothermic reactions of Ru/Al multilayers. To investigate phase formation sequences and the resulting microstructures, Ru/Al multilayers were designed via magnetron sputtering with systematic variation of bilayer modulation periods and subsequent vacuum annealing. Thin films samples were characterized by in situ high-temperature XRD, TEM imaging and diffraction. It is shown that different phase sequences appear in strong correlation with the modulation length. Depending on the multilayer design, the phase formation toward single-phase RuAl thin films happens as either a multi-step or single-step event. In particular, below a critical threshold of the modulation period, the multi-step phase formation can be suppressed, and only the desired RuAl target phase is obtained with a pronounced growth in a preferred orientation. This finding may be versatile for the targeted synthesis of intermetallic phases, contributing to further understanding of phase formation in such nanoscale multilayer systems.
- 1 August 2020
- Published by Elsevier in Acta Materialia
- Vol. 195, 579-587
Analysis of the reaction runaway in Al/Ni multilayers with combined nanocalorimetry and time-resolved X-ray diffraction
- 1 August 2020
- Published by Elsevier in Acta Materialia
- Vol. 195, 579-587
Analysis of the reaction runaway in Al/Ni multilayers with combined nanocalorimetry and time-resolved X-ray diffraction
- Open Access
- 6 July 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (1) , 011902
The role of two-stage phase formation for the solid-state runaway reaction in Al/Ni reactive multilayers
While extensively studied for heating rates below 1.7 K/s and above 1000 K/s, the solid-state phase transformations in Al/Ni reactive multilayers have not been examined at intermediate heating rates between 100 K/s and 1000 K/s. Combined nanocalorimetry and time-resolved synchrotron x-ray diffraction studies are utilized to address this range of heating rates for multilayers with an overall composition of 10 at. % Ni and a bilayer thickness of 220 nm. It was found that a two-stage phase formation of Al3Ni proceeds up to a heating rate of 1000 K/s. The two growth stages occur in the solid-state and are kinetically separated. The activation energy of the first growth stage is determined to be 137 kJ/mol, which agrees well with the literature data at low heating rates. At 1000 K/s, a transition to a runaway reaction is observed. Unusual for metallic multilayers, the reaction proceeds completely in the solid-state which is also known as “solid flame.” Using nanocalorimetry, a critical input power density for ignition of 5.8 × 104 W/cm3 was determined. The rapid succession of the two Al3Ni formation stages was identified as the underlying mechanism for the self-sustaining reaction.
- 6 July 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 117 (1) , 011902
Open AccessThe role of two-stage phase formation for the solid-state runaway reaction in Al/Ni reactive multilayers
While extensively studied for heating rates below 1.7 K/s and above 1000 K/s, the solid-state phase transformations in Al/Ni reactive multilayers have not been examined at intermediate heating rates between 100 K/s and 1000 K/s. Combined nanocalorimetry and time-resolved synchrotron x-ray diffraction studies are utilized to address this range of heating rates for multilayers with an overall composition of 10 at. % Ni and a bilayer thickness of 220 nm. It was found that a two-stage phase formation of Al3Ni proceeds up to a heating rate of 1000 K/s. The two growth stages occur in the solid-state and are kinetically separated. The activation energy of the first growth stage is determined to be 137 kJ/mol, which agrees well with the literature data at low heating rates. At 1000 K/s, a transition to a runaway reaction is observed. Unusual for metallic multilayers, the reaction proceeds completely in the solid-state which is also known as “solid flame.” Using nanocalorimetry, a critical input power density for ignition of 5.8 × 104 W/cm3 was determined. The rapid succession of the two Al3Ni formation stages was identified as the underlying mechanism for the self-sustaining reaction.
- Open Access
- 29 October 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (11) , 96
Rapid Thermal Characterization of Graphene Oxide—Nanocalorimetry as a Pathway for Novel Insights in Tribology
The use of solid lubricants such as graphene, graphene oxide, and other nanoparticles have gained notable attention in the tribological community to reduce friction and wear thus aiming at improved energy efficiency and sustainability. Tribological experiments unify rather extreme conditions such as high contact pressures, small contact areas, relative sliding motion, and rapid heating. This combination leads to mechanically- and/or thermally induced chemical, structural and microstructural modifications of the lubricating nanoparticles during rubbing thus altering their material’s properties. Due to the high sensitivity, we propose nanocalorimetry as the method of choice to shed more light on the thermally-induced processes and changes. As a model material for solid lubricants, we explore the transitions of graphene oxide under heating with 1000 °C/s up to 600 °C using quasi-adiabatic nanocalorimetry. We identify a strong exothermic runaway reaction at 317 °C. This runaway is preceded by exothermic reactions between 75–125 °C, which are correlated with the release of intercalated species and the formation of CO and CO2.
- 29 October 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (11) , 96
Open AccessRapid Thermal Characterization of Graphene Oxide—Nanocalorimetry as a Pathway for Novel Insights in Tribology
The use of solid lubricants such as graphene, graphene oxide, and other nanoparticles have gained notable attention in the tribological community to reduce friction and wear thus aiming at improved energy efficiency and sustainability. Tribological experiments unify rather extreme conditions such as high contact pressures, small contact areas, relative sliding motion, and rapid heating. This combination leads to mechanically- and/or thermally induced chemical, structural and microstructural modifications of the lubricating nanoparticles during rubbing thus altering their material’s properties. Due to the high sensitivity, we propose nanocalorimetry as the method of choice to shed more light on the thermally-induced processes and changes. As a model material for solid lubricants, we explore the transitions of graphene oxide under heating with 1000 °C/s up to 600 °C using quasi-adiabatic nanocalorimetry. We identify a strong exothermic runaway reaction at 317 °C. This runaway is preceded by exothermic reactions between 75–125 °C, which are correlated with the release of intercalated species and the formation of CO and CO2.
- 1 May 2016
- Published by Elsevier in Combustion and Flame
- Vol. 167, 259-267
The utilization of metal/metal oxide core-shell powders to enhance the reactivity of diluted thermite mixtures
- 1 May 2016
- Published by Elsevier in Combustion and Flame
- Vol. 167, 259-267
The utilization of metal/metal oxide core-shell powders to enhance the reactivity of diluted thermite mixtures
- 17 March 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (12) , 5738-5749
Effect of dilution on reaction properties and bonds formed using mechanically processed dilute thermite foils
- 17 March 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (12) , 5738-5749
Effect of dilution on reaction properties and bonds formed using mechanically processed dilute thermite foils
- Open Access
- 29 January 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 19535
Ru/Al Multilayers Integrate Maximum Energy Density and Ductility for Reactive Materials
Established and already commercialized energetic materials, such as those based on Ni/Al for joining, lack the adequate combination of high energy density and ductile reaction products. To join components, this combination is required for mechanically reliable bonds. In addition to the improvement of existing technologies, expansion into new fields of application can also be anticipated which triggers the search for improved materials. Here, we present a comprehensive characterization of the key parameters that enables us to classify the Ru/Al system as new reactive material among other energetic systems. We finally found that Ru/Al exhibits the unusual integration of high energy density and ductility. For example, we measured reaction front velocities up to 10.9 (±0.33) ms−1 and peak reaction temperatures of about 2000 °C indicating the elevated energy density. To our knowledge, such high temperatures have never been reported in experiments for metallic multilayers. In situ experiments show the synthesis of a single-phase B2-RuAl microstructure ensuring improved ductility. Molecular dynamics simulations corroborate the transformation behavior to RuAl. This study fundamentally characterizes a Ru/Al system and demonstrates its enhanced properties fulfilling the identification requirements of a novel nanoscaled energetic material.
- 29 January 2016
- Published by Springer Nature in Scientific Reports
- Vol. 6 (1) , 19535
Open AccessRu/Al Multilayers Integrate Maximum Energy Density and Ductility for Reactive Materials
Established and already commercialized energetic materials, such as those based on Ni/Al for joining, lack the adequate combination of high energy density and ductile reaction products. To join components, this combination is required for mechanically reliable bonds. In addition to the improvement of existing technologies, expansion into new fields of application can also be anticipated which triggers the search for improved materials. Here, we present a comprehensive characterization of the key parameters that enables us to classify the Ru/Al system as new reactive material among other energetic systems. We finally found that Ru/Al exhibits the unusual integration of high energy density and ductility. For example, we measured reaction front velocities up to 10.9 (±0.33) ms−1 and peak reaction temperatures of about 2000 °C indicating the elevated energy density. To our knowledge, such high temperatures have never been reported in experiments for metallic multilayers. In situ experiments show the synthesis of a single-phase B2-RuAl microstructure ensuring improved ductility. Molecular dynamics simulations corroborate the transformation behavior to RuAl. This study fundamentally characterizes a Ru/Al system and demonstrates its enhanced properties fulfilling the identification requirements of a novel nanoscaled energetic material.