Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Cecilia Ahlström has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High-Pressure Pasteurization of Oat Okara

    by Amanda Helstad, Ali Marefati, Cecilia Ahlström, Marilyn Rayner, Jeanette Purhagen, Karolina Östbring

    The issue of the short microbiological shelf life of residues from the plant-based beverage industry creates a large food waste problem. Today, the oat beverage residue, in this study referred to as oat okara, is generally converted to energy or used as animal feed. High-pressure pasteurization (200 MPa, 400 MPa, and 600 MPa) was applied to oat okara to investigate the effect on shelf life and microbiological activity. A 4-week microbiological storage study was performed and thermal properties, viscosity, and water and oil holding capacities were analyzed. The total aerobic count, including yeast and mold, was significantly reduced (p < 0.05) by 600 MPa after four weeks of storage at 4 °C. The content of lactic acid bacteria after four weeks of storage was low for untreated oat okara (3.2 log CFU/g) but, for 600 MPa, the content remained at the detection limit (2.3 log CFU/g). Conversely, the treatments of 200 MPa and 400 MPa increased the microbial content of the total aerobic count significantly (p < 0.05) after two weeks in comparison to untreated oat okara. The thermal properties of untreated and high-pressure-treated oat okara demonstrated an increase in protein denaturation of the 12S globulin, avenalin, when higher pressure was applied (400–600 MPa). This was also confirmed in the viscosity measurements where a viscosity peak for avenalin was only present for untreated and 200 MPa treated oat okara. The water holding capacity did not change as a function of high-pressure treatment (3.5–3.8 mL/g) except for the treatment at 200 MPa, which was reduced (2.7 mL/g). The oil holding capacity was constant (1.2–1.3 mL/g) after all treatments. High-pressure pasteurization of 600 MPa reduced the microbial content in oat okara resulting in a shelf life of 2–4 weeks. However, more research is required to identify the microorganisms in oat okara to achieve a microbiologically safe product that can be used for food applications.


  • Open Access

    High-Pressure Pasteurization of Soy Okara

    by Amanda Helstad, Ali Marefati, Cecilia Ahlström, Marilyn Rayner, Jeanette Purhagen, Karolina Östbring

    Okara is a by-product from the production of soy beverages, which has a high content of protein and fiber. Even though it has a high nutritional value, it is generally discarded or used as animal feed or compost. The problem is its short shelf life due to its high water content and high water activity. The aim of this study was to investigate the effect of high-pressure pasteurization at 200 MPa, 400 MPa, and 600 MPa on the shelf life of soy okara. Microbiological growth, as well as thermal properties, viscosity, water holding capacity, and oil holding capacity, was evaluated after the pressure treatments. Treatment at 600 MPa significantly reduced (p < 0.05) the growth of total aerobic count, yeast and mold, and lactic acid bacteria for up to four weeks of storage at 4 °C. The pasting properties were increased while the water and oil holding capacities of the soy okara did not significantly change (p > 0.05) after high-pressure pasteurization at 400 MPa and 600 MPa. High-pressure pasteurization is therefore a potential application technique for soy okara to produce a microbiologically safe product with maintained functional properties. However, more research is needed to optimize the process and to further investigate the microbiological species present in untreated soy okara to exclude any potential food safety risks.


  • Open Access

    Effects of Concentration and Type of Lipids on the Droplet Size, Encapsulation, Colour and Viscosity in the Oil-in-Water Emulsions Stabilised by Rapeseed Protein

    by Mirosław M. Kasprzak, Maciej Jarzębski, Wojciech Smułek, Wiktor Berski, Marzena Zając, Karolina Östbring, Cecilia Ahlström, Stanisław Ptasznik, Jacek Domagała

    The objective of this study was to extract the rapeseed protein from by-products and further examine the effect of lab-made rapeseed protein on the droplet size, microstructure, colour, encapsulation and apparent viscosity of emulsions. Rapeseed protein-stabilised emulsions with an increasing gradient of milk fat or rapeseed oil (10, 20, 30, 40 and 50%, v/v) were fabricated using a high shear rate homogenisation. All emulsions showed 100% oil encapsulation for 30 days of storage, irrespective of lipid type and the concentration used. Rapeseed oil emulsions were stable against coalescence, whereas the milk fat emulsion showed a partial micro-coalescence. The apparent viscosity of emulsions raised with increased lipid concentrations. Each of the emulsions showed a shear thinning behaviour, a typical behaviour of non-Newtonian fluids. The average droplet size was raised in milk fat and rapeseed oil emulsions when the concentration of lipids increased. A simple approach to manufacturing stable emulsions offers a feasible hint to convert protein-rich by-products into a valuable carrier of saturated or unsaturated lipids for the design of foods with a targeted lipid profile.


  • Open Access

    The Effect of Precipitation pH on Protein Recovery Yield and Emulsifying Properties in the Extraction of Protein from Cold-Pressed Rapeseed Press Cake

    by Cecilia Ahlström, Johan Thuvander, Marilyn Rayner, María Matos, Gemma Gutiérrez, Karolina Östbring

    Rapeseed is the second most cultivated oilseed after soybean and is mainly used to produce vegetable oil. The by-product rapeseed press cake is rich in high-quality proteins, thus having the possibility of becoming a new plant protein food source. This study aimed to investigate how the precipitation pH affects the protein yield, protein content, and emulsifying properties when industrially cold-pressed rapeseed press cake is used as the starting material. Proteins were extracted under alkaline conditions (pH 10.5) with an extraction coefficient of 52 ± 2% followed by precipitation at various pH (3.0–6.5). The most preferred condition in terms of process efficiency was pH 4.0, which is reflected in the zeta potential results, where the proteins’ net charge was 0 at pH 4.2. pH 4.0 also exhibited the highest protein recovery yield (33 ± 0%) and the highest protein concentration (64 ± 1%, dry basis). Proteins precipitated at pH 6.0–6.5 stabilized emulsions with the smallest initial droplet size, although emulsions stabilized by rapeseed protein precipitated at pH 5.0–6.0 showed the highest emulsion stability at 37 °C for 21 days, with a limited layer of free oil. Overall, emulsion stabilized by protein precipitated at pH 5.0 was the most stable formulation, with no layer of free oil after 21 days of incubation.


  • Open Access

    Pilot-Scale Protein Recovery from Cold-Pressed Rapeseed Press Cake: Influence of Solids Recirculation

    by Cecilia Ahlström, Johan Thuvander, Marilyn Rayner, Inger-Cecilia Mayer Labba, Ann-Sofie Sandberg, Karolina Östbring

    The agricultural sector is responsible for about 30% of greenhouse gas emissions, and thus there is a need to develop new plant-based proteins with lower climate impact. Rapeseed press cake, a by-product from rapeseed oil production, contains 30% high-quality protein. The purpose of this study was to recover protein from cold-pressed rapeseed press cakes on a pilot scale using a decanter and investigate the effect of recirculation of the spent solids fraction on protein yield. Proteins were extracted under alkaline conditions (pH 10.5) followed by precipitation at pH 3.5. Recirculating the spent solids fraction once increased the accumulated protein yield from 70% to 83%. The efficiency of the recovery process was highest in the first and second cycles. The additional yield after the third and fourth cycles was only 2%. The amino acid composition showed high levels of essential amino acids and was not reduced throughout the recovery process. The glucosinolate and phytate content was reduced in the precipitate after one cycle, although additional process steps are needed to further reduce the phytate content and limit the negative effect on mineral uptake.


  • Open Access

    Protein extraction from cold‐pressed hempseed press cake: From laboratory to pilot scale

    by Amanda Helstad, Erica Forsén, Cecilia Ahlström, Inger‐Cecilia Mayer Labba, Ann‐Sofie Sandberg, Marilyn Rayner, Jeanette K. Purhagen

    During the production of industrial hempseed oil, a press cake is formed as a byproduct, which is often used as animal feed although it contains a high amount of protein that could be used for human consumption. Extracting this valuable protein would reduce food waste and increase the availability of plant‐based protein. A protein extraction process based on the pH‐shift method was adapted to improve the protein extraction yield from industrial hempseed press cake (HPC). Parameters such as alkali extraction pH, time, and temperature, as well as isoelectric precipitation pH, were investigated in laboratory scale and were thereafter carried out in a pilot trial to explore the suitability for future scale up. The phytic acid content of the extracted protein isolate was also analyzed to investigate any potential inhibitory effect on mineral absorption. A final protein yield of 60.6%, with a precipitated protein content of 90.3% (dw), was obtained using a constant alkali extraction pH of 10.5 for 1 h at room temperature, followed by precipitation at pH 5.5. The pilot trial showed promising results for the future production of industrial hemp protein precipitate on a larger scale, showing a protein yield of 57.0% and protein content of 90.8% (dw). The amount of phytic acid in the protein isolate produced in the optimal laboratory experiment and in the pilot trial was 0.595 and 0.557 g phytic acid/100 g dw, respectively, which is 83%–88% less than in the HPC. This is in the range of other plant‐based protein sources (tofu, kidney beans, peas, etc.). Practical Application: Industrial hempseed press cake is a byproduct in the production of industrial hempseed oil, which is mostly used as animal feed, but has the potential to become an additional source of plant‐based protein for human consumption with a suitable protein extraction method. The extracted hemp protein could be used to develop new plant‐based dairy or meat analog products.


  • Open Access

    Development and Characterization of Extrudates Based on Rapeseed and Pea Protein Blends Using High-Moisture Extrusion Cooking

    by Izalin Zahari, Ferawati Ferawati, Jeanette K. Purhagen, Marilyn Rayner, Cecilia Ahlström, Amanda Helstad, Karolina Östbring

    Rapeseed protein is not currently utilized for food applications, although it has excellent physicochemical, functional, and nutritional properties similar to soy protein. Thus, the goal of this study was to create new plant-based extrudates for application as high-moisture meat analogs from a 50:50 blend of rapeseed protein concentrate (RPC) and yellow pea isolate (YPI) using high-moisture-extrusion (HME) cooking with a twin-screw extruder to gain a better understanding of the properties of the protein powders and resulting extrudates. The effects of extrusion processing parameters such as moisture content (60%, 63%, 65%, 70%), screw speed (500, 700, and 900 rpm), and a barrel temperature profile of 40–80–130–150 °C on the extrudates’ characteristics were studied. When compared to the effect of varying screw speeds, targeted moisture content had a larger impact on textural characteristics. The extrudates had a greater hardness at the same moisture content when the screw speed was reduced. The specific mechanical energy (SME) increased as the screw speed increased, while increased moisture content resulted in a small reduction in SME. The lightness (L*) of most samples was found to increase as the target moisture content increased from 60% to 70%. The RPC:YPI blend was equivalent to proteins produced from other sources and comparable to the FAO/WHO standard requirements.


  • Open Access

    The Effect of pH and Storage Temperature on the Stability of Emulsions Stabilized by Rapeseed Proteins

    by Karolina Östbring, María Matos, Ali Marefati, Cecilia Ahlström, Gemma Gutiérrez

    Rapeseed press cake (RPC), the by-product of rapeseed oil production, contains proteins with emulsifying properties, which can be used in food applications. Proteins from industrially produced RPC were extracted at pH 10.5 and precipitated at pH 3 (RPP3) and 6.5 (RPP6.5). Emulsions were formulated at three different pHs (pH 3, 4.5, and 6) with soy lecithin as control, and were stored for six months at either 4 °C or 30 °C. Zeta potential and droplet size distribution were analyzed prior to incubation, and emulsion stability was assessed over time by a Turbiscan instrument. Soy lecithin had significantly larger zeta potential (−49 mV to 66 mV) than rapeseed protein (−19 mV to 20 mV). Rapeseed protein stabilized emulsions with smaller droplets at pH close to neutral, whereas soy lecithin was more efficient at lower pHs. Emulsions stabilized by rapeseed protein had higher stability during storage compared to emulsions prepared by soy lecithin. Precipitation pH during the protein extraction process had a strong impact on the emulsion stability. RPP3 stabilized emulsions with higher stability in pHs close to neutral, whereas the opposite was found for RPP6.5, which stabilized more stable emulsions in acidic conditions. Rapeseed proteins recovered from cold-pressed RPC could be a suitable natural emulsifier and precipitation pH can be used to monitor the stability in emulsions with different pHs.


  • Top Cited Papers
    Open Access

    High-Moisture Meat Analogues Produced from Yellow Pea and Faba Bean Protein Isolates/Concentrate: Effect of Raw Material Composition and Extrusion Parameters on Texture Properties

    by Ferawati Ferawati, Izalin Zahari, Malin Barman, Mohammed Hefni, Cecilia Ahlström, Cornelia Witthöft, Karolina Östbring

    Yellow pea and faba bean are potential candidates to replace soybean-based ingredients due to their suitability for cultivation in the northern hemisphere, non-genetically modified organisms cultivation practice and low risk of allergenicity. This study examined the functionality of local yellow pea and faba bean protein isolates/concentrate as meat analogue products. The most critical factors affecting the texture properties of meat analogue were also determined. Extrusion was used to produce high-moisture meat analogues (HMMAs) from yellow pea and faba bean protein isolates/concentrates and HMMAs with fibrous layered structures was successfully produced from both imported commercial and local sources. The texture properties of the HMMA produced were mainly affected by the ash, fiber and protein content and water-holding capacity of the source protein. Three extrusion process parameters (target moisture content, extrusion temperature, screw speed), also significantly affected HMMA texture. In conclusion, functional HMMA can be produced using protein isolates derived from locally grown pulses.


  • Top Cited Papers
    Open Access

    Development of High-Moisture Meat Analogues with Hemp and Soy Protein Using Extrusion Cooking

    by Izalin Zahari, Ferawati Ferawati, Amanda Helstad, Cecilia Ahlström, Karolina Östbring, Marilyn Rayner, Jeanette K. Purhagen

    The interest in plant-based products is growing in Western countries, mostly due to health and environmental issues that arise from the consumption and production of animal-based food products. Many vegan products today are made from soy, but drawbacks include the challenges of cultivating soy in colder climates such as northern Europe. Therefore, the present study investigates whether industrial hemp (Cannabis sativa) could substitute soy in the production of high moisture meat analogues (HMMA). A twin screw co-rotating extruder was used to investigate to what extent hemp protein concentrate (HPC) could replace soy protein isolate (SPI) in HMMAs. The substitution levels of HPC were 20 wt%, 40 wt% and 60 wt%. Pasting properties and melting temperature of the protein powders were characterized by Rapid Visco Analyzer (RVA) and Differential Scanning Calorimeter (DSC), respectively and the produced HMMA was analysed by determining the texture and colour attributes. The results showed that it is possible to extrude a mixture with up to 60% HPC. HPC absorbed less water and needed a higher denaturing temperature compared to SPI. Increasing the moisture content by 5% would have resulted in a reduction of hardness and chewiness. The lightness (L* value) was found to be significantly higher in SPI product and decreased in the mixture with higher HPC (p < 0.05).