Qiang Jin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qiang Jin has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Chuansong Wu
3 shared publicationsWenchun Jiang
3 shared publicationsChuanbao Jia
MOE Key Lab for Liquid-Solid Structure Evolution and Materials Processing, Institute of Materials Joining, Shandong University , Jinan 250061, China
2 shared publications- Chuanbao Jia
MOE Key Lab for Liquid-Solid Structure Evolution and Materials Processing, Institute of Materials Joining, Shandong University, Jinan, China
2 shared publications - Chun-Mei Yi
Shandong Meiling Chemical Equipment Co., Ltd., Zibo 255430, China
2 shared publications Jun Ma
China Petroleum & Chemical Corporation Technology Department , Beijing 100029, China
2 shared publications
Latest Publications
- Open Access
- 6 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 471-484
Arc characteristics and metal transfer behavior on weld quality in rotating arc ultra-narrow gap GTAW of thick plates
- 6 June 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 43, 471-484
Open AccessArc characteristics and metal transfer behavior on weld quality in rotating arc ultra-narrow gap GTAW of thick plates
- 6 March 2026
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 148 (4) , 1-32
Residual Stress Control in Nozzle to Cylinder Butt Welds of Large-Scale Pressure Vessels Using Primary Plus Secondary Local PWHT Method
This study systematically investigated spot heating local PWHT for pressure vessel nozzle to cylinder butt welds through integrated experimental and numerical analysis. A dual-stage local heat treatment methodology, i.e., the primary plus secondary local PWHT (PS-PWHT), was developed specifically for the nozzle to cylinder butt welds, with a systematic investigation of secondary heating parameters affecting residual stress reduction. The results demonstrate that the PS-PWHT method achieves 50-70% residual stress reduction at critical inner surface locations. Two optimized secondary heating configurations, i.e. elliptical saddle-shaped secondary heating (E-SH) and rectangular saddle-shaped secondary heating (R-SH), were established based on reverse bending moment analysis of axial/hoop heating bands. Geometric parameters were quantified with recommended secondary heating distances (WDC=2 and WDS=4 ) and (2-3)t width range (where WDC and WDS are the primary and secondary heating distances for the hoop and axial heating bands, respectively. t represents wall thickness). A heating temperature range of 300-450°C was identified for secondary heating, balancing effective stress relief without material degradation and damage. The developed process control strategy demonstrates significant improvements in mitigating welding-induced residual stresses through the PS-PWHT method.- 6 March 2026
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 148 (4) , 1-32
Residual Stress Control in Nozzle to Cylinder Butt Welds of Large-Scale Pressure Vessels Using Primary Plus Secondary Local PWHT Method
This study systematically investigated spot heating local PWHT for pressure vessel nozzle to cylinder butt welds through integrated experimental and numerical analysis. A dual-stage local heat treatment methodology, i.e., the primary plus secondary local PWHT (PS-PWHT), was developed specifically for the nozzle to cylinder butt welds, with a systematic investigation of secondary heating parameters affecting residual stress reduction. The results demonstrate that the PS-PWHT method achieves 50-70% residual stress reduction at critical inner surface locations. Two optimized secondary heating configurations, i.e. elliptical saddle-shaped secondary heating (E-SH) and rectangular saddle-shaped secondary heating (R-SH), were established based on reverse bending moment analysis of axial/hoop heating bands. Geometric parameters were quantified with recommended secondary heating distances (WDC=2 and WDS=4 ) and (2-3)t width range (where WDC and WDS are the primary and secondary heating distances for the hoop and axial heating bands, respectively. t represents wall thickness). A heating temperature range of 300-450°C was identified for secondary heating, balancing effective stress relief without material degradation and damage. The developed process control strategy demonstrates significant improvements in mitigating welding-induced residual stresses through the PS-PWHT method.- 14 February 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 211
Experimental and numerical analysis of residual stress relief mechanisms of local postweld heat treatment in pressure vessels
- 14 February 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 211
Experimental and numerical analysis of residual stress relief mechanisms of local postweld heat treatment in pressure vessels
- 13 September 2022
- Published by Elsevier in Engineering Failure Analysis
- Vol. 142
Investigation on leakage cause of 13Cr pipe flange used for a Christmas tree in a high-pressure and high-temperature gas well
- 13 September 2022
- Published by Elsevier in Engineering Failure Analysis
- Vol. 142
Investigation on leakage cause of 13Cr pipe flange used for a Christmas tree in a high-pressure and high-temperature gas well
- Open Access
A Study on Microstructure, Residual Stresses and Stress Corrosion Cracking of Repair Welding on 304 Stainless Steel: Part II-Effects of Reinforcement Height
The repair reinforcement height is an important parameter of repair welding, which may have a great influence on structural integrity. In this paper, the effects of repair welding reinforcement height on the microstructure, microhardness, residual stresses and stress corrosion cracking (SCC) behavior of a 304 stainless steel-repaired joint were investigated by experimentation and simulation. With an increase of the repair weld reinforcement height, the δ ferrite content in weld and fusion zone is obviously reduced, and the ferrite shape is gradually changed from the skeleton to the worm shape. With the increase of repair welding reinforcement height, the microhardness and residual stresses decrease gradually. The tensile strength and elongation for higher repair weld reinforcement height are larger than those with lower repair weld reinforcement height. The higher the repair weld reinforcement height, the harder it is for SCC to occur. The repair welding in 304 stainless steel is recommended to be repaired no more than two times.
Open AccessA Study on Microstructure, Residual Stresses and Stress Corrosion Cracking of Repair Welding on 304 Stainless Steel: Part II-Effects of Reinforcement Height
The repair reinforcement height is an important parameter of repair welding, which may have a great influence on structural integrity. In this paper, the effects of repair welding reinforcement height on the microstructure, microhardness, residual stresses and stress corrosion cracking (SCC) behavior of a 304 stainless steel-repaired joint were investigated by experimentation and simulation. With an increase of the repair weld reinforcement height, the δ ferrite content in weld and fusion zone is obviously reduced, and the ferrite shape is gradually changed from the skeleton to the worm shape. With the increase of repair welding reinforcement height, the microhardness and residual stresses decrease gradually. The tensile strength and elongation for higher repair weld reinforcement height are larger than those with lower repair weld reinforcement height. The higher the repair weld reinforcement height, the harder it is for SCC to occur. The repair welding in 304 stainless steel is recommended to be repaired no more than two times.
- Open Access
A Study on Microstructure, Residual Stresses and Stress Corrosion Cracking of Repair Welding on 304 Stainless Steel: Part I-Effects of Heat Input
In this paper, the effect of repair welding heat input on microstructure, residual stresses, and stress corrosion cracking (SCC) sensitivity were investigated by simulation and experiment. The results show that heat input influences the microstructure, residual stresses, and SCC behavior. With the increase of heat input, both the δ-ferrite in weld and the average grain width decrease slightly, while the austenite grain size in the heat affected zone (HAZ) is slightly increased. The predicted repair welding residual stresses by simulation have good agreement with that by X-ray diffraction (XRD). The transverse residual stresses in the weld and HAZ are gradually decreased as the increases of heat input. The higher heat input can enhance the tensile strength and elongation of repaired joint. When the heat input was increased by 33%, the SCC sensitivity index was decreased by more than 60%. The macroscopic cracks are easily generated in HAZ for the smaller heat input, leading to the smaller tensile strength and elongation. The larger heat input is recommended in the repair welding in 304 stainless steel.
Open AccessA Study on Microstructure, Residual Stresses and Stress Corrosion Cracking of Repair Welding on 304 Stainless Steel: Part I-Effects of Heat Input
In this paper, the effect of repair welding heat input on microstructure, residual stresses, and stress corrosion cracking (SCC) sensitivity were investigated by simulation and experiment. The results show that heat input influences the microstructure, residual stresses, and SCC behavior. With the increase of heat input, both the δ-ferrite in weld and the average grain width decrease slightly, while the austenite grain size in the heat affected zone (HAZ) is slightly increased. The predicted repair welding residual stresses by simulation have good agreement with that by X-ray diffraction (XRD). The transverse residual stresses in the weld and HAZ are gradually decreased as the increases of heat input. The higher heat input can enhance the tensile strength and elongation of repaired joint. When the heat input was increased by 33%, the SCC sensitivity index was decreased by more than 60%. The macroscopic cracks are easily generated in HAZ for the smaller heat input, leading to the smaller tensile strength and elongation. The larger heat input is recommended in the repair welding in 304 stainless steel.
- 25 September 2014
- Published by Wiley in Journal of Petroleum Geology
- Vol. 37 (4) , 391-404
GENERATION AND ACCUMULATION OF HYDROCARBONS IN A DEEP “BURIED HILL” STRUCTURE IN THE BAXIAN DEPRESSION, BOHAI BAY BASIN, EASTERN CHINA
Significant volumes of hydrocarbons have been produced from karstified Infracambrian dolomites in a “buried hill” structure at depths of 5860m to 6027m and reservoir temperatures of 190–201°C in well Niudong‐1 in the Baxian depression, Bohai Bay Basin. This is the deepest oil and gas discovery made in eastern China so far and structures at similar depths are targets for exploration elsewhere in the Bohai Bay Basin. However the origin and accumulation of the hydrocarbons at Niudong‐1 is not clear: they may have been generated from highly mature lacustrine source rocks in the Sha‐4 Member of the Eocene Shahejie Formation; or they may have been derived from thermal cracking of previously‐accumulated oil.This paper investigates the organic geochemistry of the Sha‐4 Member source rocks and the crude oils produced from well Niudong‐1. Analyses of molecular parameters show that the hydrocarbons originated from the pyrolysis of organic matter in Sha‐4 Member source rocks, rather than from cracking of previously accumulated oil. Infracambrian dolomites at the Niudong‐1 location may have been charged with low‐maturity oil around 34 Ma ago, when the Sha‐4 Member source rocks were buried to depths of about 3500m and first entered the oil window. During further rapid burial to more than 5500m starting at about 15Ma, these source rocks became highly mature and generated significant volumes of light oil and gas. Overpressures in the source rock interval forced these hydrocarbons to migrate into unconformably‐underlying Infracambrian dolomite reservoir rocks at the Niudong‐1 structure.Significant risks are associated with future exploration of deep “buried hill” structures in the Bohai Bay Basin. Not all the structures were charged with oil, and accumulations were not necessarily preserved during Neogene burial as the reservoirs may have been breached by faulting.
- 25 September 2014
- Published by Wiley in Journal of Petroleum Geology
- Vol. 37 (4) , 391-404
GENERATION AND ACCUMULATION OF HYDROCARBONS IN A DEEP “BURIED HILL” STRUCTURE IN THE BAXIAN DEPRESSION, BOHAI BAY BASIN, EASTERN CHINA
Significant volumes of hydrocarbons have been produced from karstified Infracambrian dolomites in a “buried hill” structure at depths of 5860m to 6027m and reservoir temperatures of 190–201°C in well Niudong‐1 in the Baxian depression, Bohai Bay Basin. This is the deepest oil and gas discovery made in eastern China so far and structures at similar depths are targets for exploration elsewhere in the Bohai Bay Basin. However the origin and accumulation of the hydrocarbons at Niudong‐1 is not clear: they may have been generated from highly mature lacustrine source rocks in the Sha‐4 Member of the Eocene Shahejie Formation; or they may have been derived from thermal cracking of previously‐accumulated oil.This paper investigates the organic geochemistry of the Sha‐4 Member source rocks and the crude oils produced from well Niudong‐1. Analyses of molecular parameters show that the hydrocarbons originated from the pyrolysis of organic matter in Sha‐4 Member source rocks, rather than from cracking of previously accumulated oil. Infracambrian dolomites at the Niudong‐1 location may have been charged with low‐maturity oil around 34 Ma ago, when the Sha‐4 Member source rocks were buried to depths of about 3500m and first entered the oil window. During further rapid burial to more than 5500m starting at about 15Ma, these source rocks became highly mature and generated significant volumes of light oil and gas. Overpressures in the source rock interval forced these hydrocarbons to migrate into unconformably‐underlying Infracambrian dolomite reservoir rocks at the Niudong‐1 structure.Significant risks are associated with future exploration of deep “buried hill” structures in the Bohai Bay Basin. Not all the structures were charged with oil, and accumulations were not necessarily preserved during Neogene burial as the reservoirs may have been breached by faulting.
- 1 December 1998
- Published by Wiley in Acta Geologica Sinica - English Edition
- Vol. 72 (4) , 350-362
Meso‐Cenozoic Evolution of the Tanlu Fault and Formation of Sedimentary Basins
There are a group of large and medium‐scale Meso‐Cenozoic petroliferous basins along both sides of the Tanlu fault or within the fault zone, e.g., the Songliao basin, the Bohai Bay basin and the Subei‐Yellow Sea basin. As shown by studies of the structural types, sedimentary formations, volcanic activities, tectonic evolution as well as the time‐space relationship between the Tanlu fault zone and the basins, the formation and distribution of the basins are controlled by the movement of the Tanlu fault. This paper presents an analysis of the tectono‐geometric, kinematic and geodynamic features of the basins on the basis of integrated geological‐geophysical data, and an exploration into the internal relations between the fault and the basins as well as the formation mechanism and geodynamic processes of the basins.
- 1 December 1998
- Published by Wiley in Acta Geologica Sinica - English Edition
- Vol. 72 (4) , 350-362
Meso‐Cenozoic Evolution of the Tanlu Fault and Formation of Sedimentary Basins
There are a group of large and medium‐scale Meso‐Cenozoic petroliferous basins along both sides of the Tanlu fault or within the fault zone, e.g., the Songliao basin, the Bohai Bay basin and the Subei‐Yellow Sea basin. As shown by studies of the structural types, sedimentary formations, volcanic activities, tectonic evolution as well as the time‐space relationship between the Tanlu fault zone and the basins, the formation and distribution of the basins are controlled by the movement of the Tanlu fault. This paper presents an analysis of the tectono‐geometric, kinematic and geodynamic features of the basins on the basis of integrated geological‐geophysical data, and an exploration into the internal relations between the fault and the basins as well as the formation mechanism and geodynamic processes of the basins.