Marie André Destarac
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marie André Destarac has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
Cecilia E. García Cena
Aura Innovative Robotics and the Centre for Automation and Robotics UPM-CSIC
4 shared publications- Manuel Cardona
Research Department, Universidad Don Bosco, Soyapango 1774, El Salvador
4 shared publications Roque Saltarén Pazmiño
Centre for Automation and Robotics UPM-CSIC
4 shared publicationsCecilia E. Garcia Cena
UPM-CSIC y Aura Innovative Robotics, Centro de Automática y Robotica, Madrid, Spain
3 shared publications- Cecilia Elisabet García Cena
Escuela Técnica Superior de Ingeniería y Diseño Industrial, Universidad Politécnica de Madrid, Ronda de Valencia, 3, 28012 Madrid, Spain
2 shared publications Donald Wise
2 shared publications
Latest Publications
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
ORTE Exoskeleton: Kinematic Analysis and Dynamic Modeling
ORTE is a robotic platform developed to restore the mobility to the shoulder complex and elbow joint of upper limb impaired patients. ORTE pretends to be an effective and objective tool for the rehabilitation staff. This work presents the kinematic analysis and dynamic modeling of ORTE, a 6 Degrees-of-Freedom upper limb rehabilitation exoskeleton. The dynamic model of the mechanism is used to find the required torques to perform a set of different trajectories of daily living activities as eating or taking an object. This allows the optimal selection of actuators for this rehabilitation system.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
ORTE Exoskeleton: Kinematic Analysis and Dynamic Modeling
ORTE is a robotic platform developed to restore the mobility to the shoulder complex and elbow joint of upper limb impaired patients. ORTE pretends to be an effective and objective tool for the rehabilitation staff. This work presents the kinematic analysis and dynamic modeling of ORTE, a 6 Degrees-of-Freedom upper limb rehabilitation exoskeleton. The dynamic model of the mechanism is used to find the required torques to perform a set of different trajectories of daily living activities as eating or taking an object. This allows the optimal selection of actuators for this rehabilitation system.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
ORTE exoskeleton: Actuation system dimensioning and selection
In this work is addressed the selection of the electric motors for an upper limb rehabilitation exoskeleton based on the evaluation of the resulting torques needed to perform a set of predefined trajectories considering three load scenarios. The trajectories considered correspond with pure joint movements and the daily living activity of eating. Furthermore, in order to provide smooth movements, it is implemented a sinusoidal-linear-sinusoidal velocity profile. The torques profiles are obtained using the Simscape Multibody simulation environment. Considering the nominal and peaks velocity and resulting torques, it is proposed a set of electric motors commercially available from the manufacturer's catalogues.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
ORTE exoskeleton: Actuation system dimensioning and selection
In this work is addressed the selection of the electric motors for an upper limb rehabilitation exoskeleton based on the evaluation of the resulting torques needed to perform a set of predefined trajectories considering three load scenarios. The trajectories considered correspond with pure joint movements and the daily living activity of eating. Furthermore, in order to provide smooth movements, it is implemented a sinusoidal-linear-sinusoidal velocity profile. The torques profiles are obtained using the Simscape Multibody simulation environment. Considering the nominal and peaks velocity and resulting torques, it is proposed a set of electric motors commercially available from the manufacturer's catalogues.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Exoskeleton robots for rehabilitation: State of the art and future trends
In this paper a comprehensive review of exoskeletons for upper and lower limb rehabilitation is presented. Commercial robots with an emphasis on the pathologies they deal with are described and classified using the NASA Technology Readiness Level (TRL) metric. In addition, their movements and certifications are reviewed. Finally, future trends regarding the use of exoskeletons in the rehabilitation process are discussed.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Exoskeleton robots for rehabilitation: State of the art and future trends
In this paper a comprehensive review of exoskeletons for upper and lower limb rehabilitation is presented. Commercial robots with an emphasis on the pathologies they deal with are described and classified using the NASA Technology Readiness Level (TRL) metric. In addition, their movements and certifications are reviewed. Finally, future trends regarding the use of exoskeletons in the rehabilitation process are discussed.
- 15 March 2017
- Published by Springer Nature
- p. 71-82
Analysis of the Influence of External Actuators on the Glenohumeral Joint Movements
- 15 March 2017
- Published by Springer Nature
- p. 71-82
Analysis of the Influence of External Actuators on the Glenohumeral Joint Movements
- 15 March 2017
- Published by Springer Nature
- p. 297-308
Mechanical Design of a Robotic Exoskeleton for Upper Limb Rehabilitation
- 15 March 2017
- Published by Springer Nature
- p. 297-308
Mechanical Design of a Robotic Exoskeleton for Upper Limb Rehabilitation
- 13 October 2016
- Published by Springer Nature
- p. 1043-1047
Simulation of Rehabilitation Therapies for Brachial Plexus Injury Under the Influence of External Actuators
- 13 October 2016
- Published by Springer Nature
- p. 1043-1047
Simulation of Rehabilitation Therapies for Brachial Plexus Injury Under the Influence of External Actuators
- 13 October 2016
- Published by Springer Nature
- p. 1263-1268
Simulation of the Length Change in Muscles During the Arm Rotation for the Upper Brachial Plexus Injury
- 13 October 2016
- Published by Springer Nature
- p. 1263-1268
Simulation of the Length Change in Muscles During the Arm Rotation for the Upper Brachial Plexus Injury
- Open Access
- 5 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Systems Journal
- Vol. 10 (3) , 912-921
Modeling and Simulation of Upper Brachial Plexus Injury
This paper presents the first musculoskeletal model and simulation of an upper plexus brachial injury. From this model, it is possible to analyze forces and movement ranges in order to develop a robotic exoskeleton to improve rehabilitation. The software that currently exists for musculoskeletal modeling is varied and most have advanced features for proper analysis and study of motion simulations. While more powerful computer packages are usually expensive, there are other free and open source packages available that offer different tools to perform animations and simulations and obtain forces and moments of inertia. Among them, Musculoskeletal Modeling Software was selected to construct a model of the upper limb, which has 7° of freedom and 10 muscles. These muscles are important for two of the movements simulated in this paper that are part of the postsurgery rehabilitation protocol. We performed different movement animations that are made using the inertial measurement unit to capture real data from movements made by a human being. We also performed the simulation of forces produced in elbow flexion-extension and arm abduction-adduction of a healthy subject and one with an upper brachial plexus injury in a postoperative state to compare the force that is capable of being produced in both cases.
- 5 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Systems Journal
- Vol. 10 (3) , 912-921
Open AccessModeling and Simulation of Upper Brachial Plexus Injury
This paper presents the first musculoskeletal model and simulation of an upper plexus brachial injury. From this model, it is possible to analyze forces and movement ranges in order to develop a robotic exoskeleton to improve rehabilitation. The software that currently exists for musculoskeletal modeling is varied and most have advanced features for proper analysis and study of motion simulations. While more powerful computer packages are usually expensive, there are other free and open source packages available that offer different tools to perform animations and simulations and obtain forces and moments of inertia. Among them, Musculoskeletal Modeling Software was selected to construct a model of the upper limb, which has 7° of freedom and 10 muscles. These muscles are important for two of the movements simulated in this paper that are part of the postsurgery rehabilitation protocol. We performed different movement animations that are made using the inertial measurement unit to capture real data from movements made by a human being. We also performed the simulation of forces produced in elbow flexion-extension and arm abduction-adduction of a healthy subject and one with an upper brachial plexus injury in a postoperative state to compare the force that is capable of being produced in both cases.
- 1 January 2014
- Published by Springer Nature
- p. 195-207
Skeletal Modeling, Analysis and Simulation of Upper Limb of Human Shoulder under Brachial Plexus Injury
- 1 January 2014
- Published by Springer Nature
- p. 195-207
Skeletal Modeling, Analysis and Simulation of Upper Limb of Human Shoulder under Brachial Plexus Injury