GAGabriel Agnello

Gabriel Agnello

*This is an algorithmically generated author record based on publicly available information.

Gabriel Agnello has a total of 43 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Spatially and Temporally Resolved Mapping of Contact Electrification on Stand-Alone Ultrathin Glass Materials via Kelvin Probe Force Microscopy

    by Aayush Nayyar, Ruizhe Yang, Vashin Gautham, Sagnik Das, Haiqing Lin, Andrew C. Antony, Dean Thelen, Mayukh Nath, Gabriel Agnello, Jun Liu

    Contact electrification (CE) remains a critical challenge in advanced material technologies where uncontrolled surface charging can compromise manufacturability, reliability, and performance of the materials for practical applications. Ultrathin glass with micrometer-scale thickness is a state-of-the-art specialty oxide material for flexible touchscreens in new-generation electronic devices. Despite extensive studies on CE on thermally grown oxide thin films, the physical and chemical properties of the stand-alone ultrathin oxide materials could be very different and thus lead to distinct CE behaviors. Such behaviors have not been experimentally investigated due to the challenge of their ultrathin form factor as well as the lack of experimental methods that would allow the successful study of CE on stand-alone ultrathin glass materials. Here, we, for the first time, visualize and quantify CE-induced surface charges on ultrathin glasses using sideband-mode Kelvin probe force microscopy (KPFM). To enable the KPFM measurement, we have established experimental strategies, including electrode preparation enabling the measuring circuit, and surface cleaning procedures improving surface activation and hydrophilicity. Nanosized atomic force microscopy (AFM) probes were used to scan and induce triboelectric charges on the stand-alone glass surfaces with a variety of thicknesses (30–100 μm) under ultrapure N2 conditions. Time-dependent measurements reveal the surface charges on a 30 μm-thick glass sample decay from 4.47 to 0.37 V in 240 min. Moreover, we found that electrostatic charges exhibit a capacitor-like discharging behavior primarily through the bulk material yielding a long relaxation time constant of ∼41 min, which is different from the lateral surface discharging behavior in a thermally grown SiO2 thin film reported previously. Furthermore, the thickness-dependent surface charging effect was characterized for the ultrathin glass substrates, where the change in contact potential difference between the charged and uncharged region (ΔVCPD) was found to remain nearly constant across this thickness range from 1.39 ± 0.17 V at 30 μm to 1.34 ± 0.29 V at 100 μm. A self-capacitance analytical model was developed and employed to estimate the corresponding surface charge density (σ), yielding comparable values of 136.26 ± 16.25 μC/m2 at 30 μm and 131.44 ± 28.41 μC/m2 at 100 μm. Additionally, the external bias applied to the AFM tips can be used to enhance, suppress, or invert the intrinsic CE response of glass materials. This work extends nanoscale CE characterization beyond oxide thin films to stand-alone oxide materials, providing a framework to understand and manipulate electrostatic charging in glass systems for practical applications.

  • Open Access

    Spatially and Temporally Resolved Mapping of Contact Electrification on Stand-Alone Ultrathin Glass Materials via Kelvin Probe Force Microscopy

    by Aayush Nayyar, Ruizhe Yang, Vashin Gautham, Sagnik Das, Haiqing Lin, Andrew C. Antony, Dean Thelen, Mayukh Nath, Gabriel Agnello, Jun Liu

    Contact electrification (CE) remains a critical challenge in advanced material technologies where uncontrolled surface charging can compromise manufacturability, reliability, and performance in practical applications. Ultrathin glass with micrometer-scale thickness is a state-of-the-art specialty oxide material for flexible touchscreens in next-generation electronic devices. Here, we visualize and quantify CE-induced surface charges on ultrathin glass using sideband-mode Kelvin probe force microscopy (KPFM). Nanoscale atomic force microscopy (AFM) probes are used to scan and induce triboelectric charges on stand-alone glass surfaces under ultra-pure N$_2$ conditions. Time-dependent measurements reveal that surface charges on a 30~$μ$m-thick glass sample decay from 4.47~V to 0.37~V over 240~minutes. Furthermore, electrostatic charges are found to exhibit capacitor-like discharging behavior primarily through the bulk material, yielding a long relaxation time constant of approximately 41~minutes. This behavior differs from the lateral surface discharging observed in thermally grown SiO$2$ thin films reported previously. A self-capacitance analytical model is developed to estimate the corresponding surface charge density ($σ$), yielding comparable values of 136.26~$\pm$~16.25~$μ$C/m$^2$ at 30~$μ$m and 131.44~$\pm$~28.41~$μ$C/m$^2$ at 100~$μ$m. Additionally, external bias applied to AFM tips can be used to enhance, suppress, or invert the intrinsic CE response of glass materials.

  • Water Adsorption Isotherm and Surface Conductivity of Boroaluminosilicate Glasses

    by Yen-Ting Lin, Gabriel Agnello, Mason Link, Yiwen Guo, Ava N. Zoba, Andrew Antony, Nicholas J. Smith, Joy Banerjee, Seong H. Kim

    The surface resistivity of boroaluminosilicate display glasses, which may affect the downstream display panel manufacturing, varies with the relative humidity (RH) of the environment, but the origin of this RH dependence has not been well understood. We have measured the water adsorption behavior on Corning Eagle XG (Glass-E) and Lotus NXT (Glass-L) glass panels using Brewster angle transmission infrared spectroscopy. The IR spectra of adsorbed water were analyzed to obtain the effective thickness of adsorbed water, the distribution of hydrogen-bonding interactions among the adsorbed water molecules, and the isosteric heat of water adsorption. These characteristics were compared with the electrical conductivity (inverse of resistivity) of these two glasses [Appl. Surf. Sci. 2015, 356, 1189]. This comparison revealed the correlation between the conductivity and the water layer structure, which could explain the surface resistivity difference between Glass-E and Glass-L as a function of RH. This study also disputed the previous hypothesis that the water adsorption isotherm would be governed by the areal density of the surface hydroxyl group; instead, it suggested that the network modifier ions may also play a critical role, especially in the intermediate RH regime.


  • Surface chemistry, water adsorption/desorption, and electrostatic charging behavior of display glass panel: Effect of rinsing solution pH

    by Yen-Ting Lin, Ava N. Zoba, Nicholas J. Smith, Joy Banerjee, Andrew C. Antony, Gabriel Agnello, Seong H. Kim


  • Revealing ‘invisible’ subsurface structural change/damage in silicate glass made by ‘nearly-elastic contact’ with a spherical smooth surface

    by Yen-Ting Lin, Andrew L. Ogrinc, Ava N. Zoba, Jongcheol Lee, Seokhoon Jang, Nicholas J. Smith, Joy Banerjee, Andrew Antony, Gabriel Agnello, Seong H. Kim


  • Particle Size and Humidity Effects on Nanocellulose Adhesion to Glass: Implications for Mitigating Particulate Contamination in Industrial Processes

    by Yen-Ting Lin, Wanda Walczak, Joy Banerjee, Nicholas J. Smith, Gabriel Agnello, Ava N. Zoba, Robert Manley, Seong H. Kim


  • Passivation of Mid-Gap Electronic States at Calcium Aluminosilicate Glass Surfaces upon Water Exposure: An Ab Initio Study

    by Andrew C. Antony, Sushmit Goyal, Hyunhang Park, Joy Banerjee, Nicholas J. Smith, Gabriel Agnello, Robert G. Manley

    When a clean glass surface is exposed to humid air, a thin water layer forms on the hydrophilic surface. Using ab initio molecular dynamics, we simulate the changes in the electronic structure of a CaO-Al2O3-SiO2 glass model upon vacuum fracture and subsequent exposure to H2O. When the glass is fractured, dangling bonds form, which lower the band gap of the surface by similar to 1.8 eV compared to the bulk value due to mid-gap surface states. When H2O adsorbs onto the vacuum-fractured surface, the band gap increases to a value closer to that of the bulk band gap. Using two different hydroxylation methods, we find that the calculated band gap of the glass surface depends on the hydroxylation state. Surfaces with similar to 4.8 OH/nm(2) have smaller band gaps due to unfilled surface states, and surfaces with similar to 2.5 OH/nm(2) have larger band gaps with no apparent unfilled surface states. The resulting changes in the electronic structure, quantified by electron affinity and work function values, are hypothesized to play an important role in the electrostatic charge transfer based on the principles of surface state theory, which posit that the density of electronic surface states determines the amount of electronic charge transfer to or from material surfaces.


  • Water adsorption on silica and calcium‐boroaluminosilicate glass surfaces—Thickness and hydrogen bonding of water layer

    by Yen‐Ting Lin, Nicholas J. Smith, Joy Banerjee, Gabriel Agnello, Robert G. Manley, Wanda J. Walczak, Seong H. Kim

    Adsorption isotherm of water on silica (modeled with fused quartz) and calcium‐boroaluminosilicate (Ca‐BAS) glass surfaces as a function of relative humidity (RH) was studied using Fourier transform infrared (FTIR) spectroscopy. The effective thickness of the adsorbed water layer and the distribution of hydrogen bonding interactions of water molecules in the adsorbed layer were determined by comparing the transmission FTIR spectra collected at the Brewster incidence angle with the theoretically calculated spectra. In the sub‐monolayer regime (60% RH), the total amount as well as the hydrogen bonding interactions of adsorbed water layers become insensitive to the surface chemistry and are governed mostly by the phase transition (vapor condensation) behavior. Overall, this study reveals how the water layer thickness and structure on the multicomponent silicate glass surface in ambient conditions are different from those on the pure silica surface.


  • Structure of CAS glass surfaces and electrostatic contact charging behavior: A joint simulation and experimental investigation

    by Gabriel Agnello, Liaoyuan Wang, Nicholas Smith, Robert Manley, Alastair Cormack

    Surface structures of CAS models with various Al 2 O 3 /CaO ratios, (80:10:10), (70:15:15), (60:20:20), and (50:25:25), have been simulated using classical MD methods. Atomistic surface structures, CN and Q n distributions, radial distribution functions, z‐axis concentration profiles, and ring‐size distributions were employed to study the surface structures. While bridging oxygen (BO) and triclustered oxygen (TBO) surface concentrations closely mimic those observed in the bulk structures, nonbridging oxygen (NBO) concentration exhibits a nonlinear trend with composition. Surface analysis has also showed that both 3‐ and 5‐coordinated Al (Al C3 and Al C5 ) exist in the near‐surface region, with concentrations that differ from the respective bulk structures. There are enhancements in the concentrations of small (2‐ and 3‐membered) rings that are closely related with the spatial proximity of TBO to Al C5 . These complexes, and their variations with glass composition, appear to be closely correlated with experimental electrostatic contact charging data.


  • P‐82: Improved Methodology for Testing Edge Strength for Ultra‐Thin Panels

    by Gabriel Agnello, Amber Tremper, Weidong Li, Peter Knowles

    Traditional testing methodologies (four point bend and three point bend) have limited effectiveness as panel thicknesses decrease due to a variety of interconnected factors. This limited effectiveness impacts the ability to make reliability predictions based on edge strength measurements. This paper provides an improved methodology for testing the edge strength of ultra‐thin panels for reliability predictions through a system of rollers strategically placed only at the edge of the glass panel.