Mahmoud Ibrahim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mahmoud Ibrahim has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Anton Rassõlkin
Department of Electrical Power Engineering and Mechatronics, Tallinn University of Technology, 19086 Tallinn, Estonia
6 shared publications - Ants Kallaste
Tallinn University of Technology
3 shared publications - Toomas Vaimann
Tallinn University of Technology
3 shared publications Anton Rassõlkin
Department of Electrical Power Engineering and Mechatronics Tallinn University of Technology Tallinn Estonia
2 shared publications- Assem Meghawer
Department of Electrical Power Engineering and Mechatronics, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
1 shared publication - Hans Tiismus
Tallinn University of Technology
1 shared publication
Latest Publications
- Open Access
A Scenario-Based Hardware-in-the-Loop Platform for Real-Time Road-Load Emulation on Production Micromobility Drives
Software-defined electric vehicles have reached micromobility, creating a growing need to evaluate how controller software shapes drive performance and energy use. This requires experimental platforms with quantified emulation fidelity and measurement performance. This paper presents a scenario-based hardware-in-the-loop platform combining a production e-scooter drive, a controlled magnetic particle brake, and a real-time road-load model. The platform reproduces rolling resistance, aerodynamic drag, and speed-gated inertial demand for a nominal 90 kg vehicle. Across eight repetitions of a scaled ECE-15 urban cycle, including a cold first run, the protective load cap retained 99.51% of the commanded load impulse. A post hoc sensitivity analysis of the seven warm runs gave 99.71%. Measured torque and speed tracking root-mean-square errors over all eight runs were 0.704 N·m and 0.593 km/h. Separate electrical characterization produced a machine efficiency map peaking at 86.3% and cycle-energy measurements with a coefficient of variation of 0.72%. Subsampling unfiltered 200 kHz recordings at every sampling offset gave a maximum absolute cycle-energy error of 0.14% at 2 kHz, a hundredfold reduction in retained samples under the tested conditions. These results provide a quantified experimental basis for micromobility drive testing and subsequent controller-software comparisons.
Open AccessA Scenario-Based Hardware-in-the-Loop Platform for Real-Time Road-Load Emulation on Production Micromobility Drives
Software-defined electric vehicles have reached micromobility, creating a growing need to evaluate how controller software shapes drive performance and energy use. This requires experimental platforms with quantified emulation fidelity and measurement performance. This paper presents a scenario-based hardware-in-the-loop platform combining a production e-scooter drive, a controlled magnetic particle brake, and a real-time road-load model. The platform reproduces rolling resistance, aerodynamic drag, and speed-gated inertial demand for a nominal 90 kg vehicle. Across eight repetitions of a scaled ECE-15 urban cycle, including a cold first run, the protective load cap retained 99.51% of the commanded load impulse. A post hoc sensitivity analysis of the seven warm runs gave 99.71%. Measured torque and speed tracking root-mean-square errors over all eight runs were 0.704 N·m and 0.593 km/h. Separate electrical characterization produced a machine efficiency map peaking at 86.3% and cycle-energy measurements with a coefficient of variation of 0.72%. Subsampling unfiltered 200 kHz recordings at every sampling offset gave a maximum absolute cycle-energy error of 0.14% at 2 kHz, a hundredfold reduction in retained samples under the tested conditions. These results provide a quantified experimental basis for micromobility drive testing and subsequent controller-software comparisons.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 62 (10) , 7205207
Topology Optimization of Additively Manufactured Outer-Rotor Permanent Magnet Motor
This paper presents a Topology Optimization (TO) method for the rotor back iron of outer rotor permanent magnet Brushless DC (BLDC) motors, particularly for EV scooter applications. A non-iterative analytical TO method for the rotor back iron that removes low flux utilization regions while preserving the main magnetic flux path. The Normalized Gaussian Network (NGNet) based TO is used as a benchmark to evaluate the proposed method and highlight the computational advantage of analytical TO. Unlike the NGNet approach, which requires iterative genetic algorithm optimization, the proposed analytical method determines the optimized back iron geometry from magnetic flux continuity and saturation constraints with minimal computational effort. The optimization results in a lighter rotor and improved torque density while preserving the back-EMF and torque waveform characteristics. The initial and optimized rotor back irons were fabricated using Additive Manufacturing (AM) with a material composition of Fe–3.7%Si. The difference between the simulated and experimentally measured torque was found to be approximately 5.09%.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 62 (10) , 7205207
Topology Optimization of Additively Manufactured Outer-Rotor Permanent Magnet Motor
This paper presents a Topology Optimization (TO) method for the rotor back iron of outer rotor permanent magnet Brushless DC (BLDC) motors, particularly for EV scooter applications. A non-iterative analytical TO method for the rotor back iron that removes low flux utilization regions while preserving the main magnetic flux path. The Normalized Gaussian Network (NGNet) based TO is used as a benchmark to evaluate the proposed method and highlight the computational advantage of analytical TO. Unlike the NGNet approach, which requires iterative genetic algorithm optimization, the proposed analytical method determines the optimized back iron geometry from magnetic flux continuity and saturation constraints with minimal computational effort. The optimization results in a lighter rotor and improved torque density while preserving the back-EMF and torque waveform characteristics. The initial and optimized rotor back irons were fabricated using Additive Manufacturing (AM) with a material composition of Fe–3.7%Si. The difference between the simulated and experimentally measured torque was found to be approximately 5.09%.
- Open Access
Overview of Electromagnetic Interference Mechanisms and System-Level Effects in MHz-Range Wireless Charging for Electric Vehicle Applications
Wireless power transfer (WPT) systems for electric vehicles (EVs) are increasingly being studied in the MHz range to increase power density and reduce the size of passive components. However, operation at higher frequencies significantly changes electromagnetic interference (EMI) behaavior. Fast switching in SiC- and GaN-based inverters, high-Q resonant operation, and frequency-dependent parasitic capacitances create conductive, capacitive, and magnetic interference mechanisms that are less significant in conventional kHz-range systems. Although many existing studies focus on power-transfer efficiency and converter optimization, EMI mechanisms in MHz-range EV WPT systems remain insufficiently systematized from a system-level electromagnetic perspective. This paper presents a state-of-the-art review of EMI generation mechanisms and system-level effects in high-frequency WPT systems for electric vehicles. The review considers the main interference sources and coupling paths, including switching-induced common-mode currents, resonant amplification of current and voltage stress, capacitive coupling between the coupler and nearby conductive structures, and magnetic-field redistribution caused by coil misalignment. Special attention is given to the transition from lumped-element assumptions to more distributed electromagnetic behavior at higher frequencies. The review also discusses the possible impact of these mechanisms on vehicle electronic subsystems and highlights the need for frequency-aware electromagnetic design, integrated modeling, and more rigorous EMC assessment for reliable MHz-range wireless EV charging systems.
Open AccessOverview of Electromagnetic Interference Mechanisms and System-Level Effects in MHz-Range Wireless Charging for Electric Vehicle Applications
Wireless power transfer (WPT) systems for electric vehicles (EVs) are increasingly being studied in the MHz range to increase power density and reduce the size of passive components. However, operation at higher frequencies significantly changes electromagnetic interference (EMI) behaavior. Fast switching in SiC- and GaN-based inverters, high-Q resonant operation, and frequency-dependent parasitic capacitances create conductive, capacitive, and magnetic interference mechanisms that are less significant in conventional kHz-range systems. Although many existing studies focus on power-transfer efficiency and converter optimization, EMI mechanisms in MHz-range EV WPT systems remain insufficiently systematized from a system-level electromagnetic perspective. This paper presents a state-of-the-art review of EMI generation mechanisms and system-level effects in high-frequency WPT systems for electric vehicles. The review considers the main interference sources and coupling paths, including switching-induced common-mode currents, resonant amplification of current and voltage stress, capacitive coupling between the coupler and nearby conductive structures, and magnetic-field redistribution caused by coil misalignment. Special attention is given to the transition from lumped-element assumptions to more distributed electromagnetic behavior at higher frequencies. The review also discusses the possible impact of these mechanisms on vehicle electronic subsystems and highlights the need for frequency-aware electromagnetic design, integrated modeling, and more rigorous EMC assessment for reliable MHz-range wireless EV charging systems.
- Open Access
- 20 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 7, 160-178
The Road Ahead: A Comprehensive Review of Recent Advances in Traffic Sign and Lane Line Recognition for Autonomous Systems
The perception systems for Traffic Sign Recognition (TSR) and Lane Line Recognition (LLR) are foundational pillars for the safe and effective operation of Advanced Driver-Assistance Systems (ADAS) and fully autonomous vehicles. This review provides a comprehensive analysis of the latest academic research in these domains, strictly focusing on literature published from October 2024 to the present. The analysis reveals several key trends shaping the field. In TSR, architectural evolution is characterized by the refinement of Convolutional Neural Networks (CNNs), the specialization of light-weight YOLO-based models for real-time embedded applications, and the emergence of hybrid CNN-Transformer architectures. Concurrently, a significant research thrust is dedicated to enhancing robustness against environmental adversities and a growing spectrum of sophisticated, physically plausible adversarial attacks. In LLR, the paradigm is rapidly shifting from 2D image-plane detection to full 3D spatial localization and topology reasoning, driven by Transformer-based models that excel at capturing global context and long-range dependencies. Cross-cutting themes common to both domains include a relentless drive for computational efficiency, a data-centric approach marked by the creation of new, challenging benchmarks for adverse conditions and 3D perception, and the nascent but transformative integration of multi-task learning and Vision-Language Models (VLMs) to build systems capable of holistic scene reasoning. Despite significant progress, several key challenges persist in the field of domain generalization, particularly in handling long-tail corner cases and developing safety-aware evaluation metrics. Future research is expected to focus on self-supervised learning, stronger integration between perception and control systems, and the advancement of trustworthy AI through improved explainability and robust-ness. These efforts will lay the groundwork for the next generation of intelligent vehicle systems.
- 20 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 7, 160-178
Open AccessThe Road Ahead: A Comprehensive Review of Recent Advances in Traffic Sign and Lane Line Recognition for Autonomous Systems
The perception systems for Traffic Sign Recognition (TSR) and Lane Line Recognition (LLR) are foundational pillars for the safe and effective operation of Advanced Driver-Assistance Systems (ADAS) and fully autonomous vehicles. This review provides a comprehensive analysis of the latest academic research in these domains, strictly focusing on literature published from October 2024 to the present. The analysis reveals several key trends shaping the field. In TSR, architectural evolution is characterized by the refinement of Convolutional Neural Networks (CNNs), the specialization of light-weight YOLO-based models for real-time embedded applications, and the emergence of hybrid CNN-Transformer architectures. Concurrently, a significant research thrust is dedicated to enhancing robustness against environmental adversities and a growing spectrum of sophisticated, physically plausible adversarial attacks. In LLR, the paradigm is rapidly shifting from 2D image-plane detection to full 3D spatial localization and topology reasoning, driven by Transformer-based models that excel at capturing global context and long-range dependencies. Cross-cutting themes common to both domains include a relentless drive for computational efficiency, a data-centric approach marked by the creation of new, challenging benchmarks for adverse conditions and 3D perception, and the nascent but transformative integration of multi-task learning and Vision-Language Models (VLMs) to build systems capable of holistic scene reasoning. Despite significant progress, several key challenges persist in the field of domain generalization, particularly in handling long-tail corner cases and developing safety-aware evaluation metrics. Future research is expected to focus on self-supervised learning, stronger integration between perception and control systems, and the advancement of trustworthy AI through improved explainability and robust-ness. These efforts will lay the groundwork for the next generation of intelligent vehicle systems.
- Open Access
Performance Optimization of a High-Speed Permanent Magnet Synchronous Motor Drive System for Formula Electric Vehicle Application
The proliferation of electric vehicle (EV) racing competitions, such as Formula electric vehicle (FEV) competitions, has intensified the quest for high-performance electric propulsion systems. High-speed permanent magnet synchronous motors (PMSMs) for FEVs necessitate an optimized control strategy that adeptly manages the complex interplay between electromagnetic torque production and minimal power loss, ensuring peak operational efficiency and performance stability across the full speed range. This paper delves into the optimization of high-speed PMSM, pivotal for its application in FEVs. It begins with a thorough overview of the FEV motor’s basic principles, followed by the derivation of a detailed mathematical model that lays the groundwork for subsequent analyses. Utilizing MATLAB/Simulink, a simulation model of the motor drive system was constructed. The proposed strategy synergizes the principles of maximum torque per ampere (MTPA) with the flux weakening control technique instead of conventional zero direct axis current (ZDAC), aiming to push the boundaries of motor performance while navigating the inherent limitations of high-speed operation. Covariance matrix adaptation evolution strategy (CMA-ES) was deployed to determine the optimal d-q axis current ratio achieving maximum operating torque without overdesign problems. The implementation of the optimized control strategy was rigorously tested on the simulation model, with subsequent validation conducted on a real test bench setup. The outcomes of the proposed technique reveal that the tailored control strategy significantly elevates motor torque performance by almost 22%, marking a pivotal advancement in the domain of high-speed PMSM.
Open AccessPerformance Optimization of a High-Speed Permanent Magnet Synchronous Motor Drive System for Formula Electric Vehicle Application
The proliferation of electric vehicle (EV) racing competitions, such as Formula electric vehicle (FEV) competitions, has intensified the quest for high-performance electric propulsion systems. High-speed permanent magnet synchronous motors (PMSMs) for FEVs necessitate an optimized control strategy that adeptly manages the complex interplay between electromagnetic torque production and minimal power loss, ensuring peak operational efficiency and performance stability across the full speed range. This paper delves into the optimization of high-speed PMSM, pivotal for its application in FEVs. It begins with a thorough overview of the FEV motor’s basic principles, followed by the derivation of a detailed mathematical model that lays the groundwork for subsequent analyses. Utilizing MATLAB/Simulink, a simulation model of the motor drive system was constructed. The proposed strategy synergizes the principles of maximum torque per ampere (MTPA) with the flux weakening control technique instead of conventional zero direct axis current (ZDAC), aiming to push the boundaries of motor performance while navigating the inherent limitations of high-speed operation. Covariance matrix adaptation evolution strategy (CMA-ES) was deployed to determine the optimal d-q axis current ratio achieving maximum operating torque without overdesign problems. The implementation of the optimized control strategy was rigorously tested on the simulation model, with subsequent validation conducted on a real test bench setup. The outcomes of the proposed technique reveal that the tailored control strategy significantly elevates motor torque performance by almost 22%, marking a pivotal advancement in the domain of high-speed PMSM.
- Open Access
- 7 January 2025
- Published by Institution of Engineering and Technology (IET) in Digital Twins and Applications
- Vol. 2 (1)
Digital shadow of an electric vehicle‐permanent magnet synchronous motor drive for real‐time performance monitoring
Digital twin (DT) technology has been utilised in many applications including electric vehicles (EVs). A DT is a virtual representation of a physical object, enabled through real‐time data integration, simulation, and optimisation tools. Unlike conventional simulations, which are typically offline and lack real‐time interaction, a DT continuously synchronises with the physical system, enabling dynamic performance monitoring and predictive analytics. Achieving a full DT involves progressive stages, with the digital shadow (DS) being the final step before realising a bidirectional DT. Building a DS provides a scalable real‐time performance monitoring and fault detection framework, enabling proactive decision‐making in EV operations. This study introduces a DS system specifically designed to monitor the performance of a permanent magnet synchronous motor (PMSM) drive system in EVs, marking a critical phase towards a complete DT. The methodology for creating the DS is detailed, including the establishment of a comprehensive test bench for the EV powertrain as the physical reference model. The mathematical model of the EV‐PMSM was formulated, and an advanced estimation model utilising the extended Kalman filter (EKF) was implemented. MATLAB/Simulink was employed to develop the motor’s digital model. Real‐time data acquisition from the physical model was facilitated through a data acquisition system (DAS) equipped with a controller area network (CAN) communication interface. The digital model underwent thorough validation against sensory data collected from the test bench. The motor digital model was deployed to a DS framework enabled through real‐time data flow from the actual EV during real‐world driving conditions. The results demonstrated a high accuracy of 97% between the DS predictions and the corresponding EV data, confirming the DS’s reliability. These findings pave the way for future advancements, including bidirectional interaction and the realisation of a full DT.
- 7 January 2025
- Published by Institution of Engineering and Technology (IET) in Digital Twins and Applications
- Vol. 2 (1)
Open AccessDigital shadow of an electric vehicle‐permanent magnet synchronous motor drive for real‐time performance monitoring
Digital twin (DT) technology has been utilised in many applications including electric vehicles (EVs). A DT is a virtual representation of a physical object, enabled through real‐time data integration, simulation, and optimisation tools. Unlike conventional simulations, which are typically offline and lack real‐time interaction, a DT continuously synchronises with the physical system, enabling dynamic performance monitoring and predictive analytics. Achieving a full DT involves progressive stages, with the digital shadow (DS) being the final step before realising a bidirectional DT. Building a DS provides a scalable real‐time performance monitoring and fault detection framework, enabling proactive decision‐making in EV operations. This study introduces a DS system specifically designed to monitor the performance of a permanent magnet synchronous motor (PMSM) drive system in EVs, marking a critical phase towards a complete DT. The methodology for creating the DS is detailed, including the establishment of a comprehensive test bench for the EV powertrain as the physical reference model. The mathematical model of the EV‐PMSM was formulated, and an advanced estimation model utilising the extended Kalman filter (EKF) was implemented. MATLAB/Simulink was employed to develop the motor’s digital model. Real‐time data acquisition from the physical model was facilitated through a data acquisition system (DAS) equipped with a controller area network (CAN) communication interface. The digital model underwent thorough validation against sensory data collected from the test bench. The motor digital model was deployed to a DS framework enabled through real‐time data flow from the actual EV during real‐world driving conditions. The results demonstrated a high accuracy of 97% between the DS predictions and the corresponding EV data, confirming the DS’s reliability. These findings pave the way for future advancements, including bidirectional interaction and the realisation of a full DT.
- Open Access
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 19 (1)
Hybrid‐Driven Digital Twin Modelling Framework for an EV Propulsion Drive System
Digital twin (DT) plays a vital role across various applications, notably in electric vehicles (EVs). It serves as a virtual counterpart to physical systems. Repurposing legacy EV propulsion systems—those developed prior to the rise of connected vehicle technologies—can reduce electronic waste and support sustainability goals. However, adapting DTs in such systems is challenging due to limited connectivity, incomplete schematics, and performance degradation over time. This paper presents a hybrid‐driven DT modelling framework for an EV repurposed with a legacy propulsion system, where some components, like the drive system, have uncertain parameters. A physics‐based model is developed for the motor, leveraging its well‐defined parameters, while a data‐driven model is applied to the drive system due to its uncertainty. The data‐driven model was developed using a nonlinear autoregressive neural network with exogenous inputs (NARX). It was trained on physical test bench data and achieved a validation RMSE of 0.04 on unseen data. A hybrid‐driven model, combining the NARX‐based drive system with a physics‐based motor model, was first validated offline in MATLAB/Simulink, then deployed on a speedgoat baseline target machine for real‐world testing. The deployment enabled validation under real world vehicle conditions beyond the test bench and assessment of its real‐time capability. Real‐time testing demonstrated high steady‐state accuracy and reliable performance, with an average execution cycle of 8 ms, 60% CPU load, and 300 MB memory usage. Communication via user datagram protocol confirmed the model's real‐time readiness and suitability for practical DT integration.
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Intelligent Transport Systems
- Vol. 19 (1)
Open AccessHybrid‐Driven Digital Twin Modelling Framework for an EV Propulsion Drive System
Digital twin (DT) plays a vital role across various applications, notably in electric vehicles (EVs). It serves as a virtual counterpart to physical systems. Repurposing legacy EV propulsion systems—those developed prior to the rise of connected vehicle technologies—can reduce electronic waste and support sustainability goals. However, adapting DTs in such systems is challenging due to limited connectivity, incomplete schematics, and performance degradation over time. This paper presents a hybrid‐driven DT modelling framework for an EV repurposed with a legacy propulsion system, where some components, like the drive system, have uncertain parameters. A physics‐based model is developed for the motor, leveraging its well‐defined parameters, while a data‐driven model is applied to the drive system due to its uncertainty. The data‐driven model was developed using a nonlinear autoregressive neural network with exogenous inputs (NARX). It was trained on physical test bench data and achieved a validation RMSE of 0.04 on unseen data. A hybrid‐driven model, combining the NARX‐based drive system with a physics‐based motor model, was first validated offline in MATLAB/Simulink, then deployed on a speedgoat baseline target machine for real‐world testing. The deployment enabled validation under real world vehicle conditions beyond the test bench and assessment of its real‐time capability. Real‐time testing demonstrated high steady‐state accuracy and reliable performance, with an average execution cycle of 8 ms, 60% CPU load, and 300 MB memory usage. Communication via user datagram protocol confirmed the model's real‐time readiness and suitability for practical DT integration.
- Open Access
Digital Twin as a Virtual Sensor for Wind Turbine Applications
Digital twins (DTs) have been implemented in various applications, including wind turbine generators (WTGs). They are used to create virtual replicas of physical turbines, which can be used to monitor and optimize their performance. By simulating the behavior of physical turbines in real time, DTs enable operators to predict potential failures and optimize maintenance schedules, resulting in increased reliability, safety, and efficiency. WTGs rely on accurate wind speed measurements for safe and efficient operation. However, physical wind speed sensors are prone to inaccuracies and failures due to environmental factors or inherent issues, resulting in partial or missing measurements that can affect the turbine’s performance. This paper proposes a DT-based sensing methodology to overcome these limitations by augmenting the physical sensor platform with virtual sensor arrays. A test bench of a direct drive WTG based on a permanent magnet synchronous generator (PMSG) was prepared, and its mathematical model was derived. MATLAB/Simulink was used to develop the WTG virtual model based on its mathematical model. A data acquisition system (DAS) equipped with an ActiveX server was used to facilitate real-time data exchange between the virtual and physical models. The virtual sensor was then validated and tuned using real sensory data from the physical turbine model. The results from the developed DT model showed the power of the DT as a virtual sensor in estimating wind speed according to the generated power.
Open AccessDigital Twin as a Virtual Sensor for Wind Turbine Applications
Digital twins (DTs) have been implemented in various applications, including wind turbine generators (WTGs). They are used to create virtual replicas of physical turbines, which can be used to monitor and optimize their performance. By simulating the behavior of physical turbines in real time, DTs enable operators to predict potential failures and optimize maintenance schedules, resulting in increased reliability, safety, and efficiency. WTGs rely on accurate wind speed measurements for safe and efficient operation. However, physical wind speed sensors are prone to inaccuracies and failures due to environmental factors or inherent issues, resulting in partial or missing measurements that can affect the turbine’s performance. This paper proposes a DT-based sensing methodology to overcome these limitations by augmenting the physical sensor platform with virtual sensor arrays. A test bench of a direct drive WTG based on a permanent magnet synchronous generator (PMSG) was prepared, and its mathematical model was derived. MATLAB/Simulink was used to develop the WTG virtual model based on its mathematical model. A data acquisition system (DAS) equipped with an ActiveX server was used to facilitate real-time data exchange between the virtual and physical models. The virtual sensor was then validated and tuned using real sensory data from the physical turbine model. The results from the developed DT model showed the power of the DT as a virtual sensor in estimating wind speed according to the generated power.
- Top Cited PapersOpen Access
Overview of Digital Twin Platforms for EV Applications
Digital twin (DT) technology has been used in a wide range of applications, including electric vehicles. The DT platform provides a virtual representation or advanced simulation of a physical object in real-time. The implementation of DT on various aspects of EVs has recently transpired in different research studies. Generally, DT can emulate the actual vehicle on the road to predict/optimize its performance and improve vehicle safety. Additionally, DT can be used for the optimization of manufacturing processes, real-time condition monitoring (at all levels and in all powertrain components), energy management optimization, repurposing of the components, and even recycling processes. This paper presents an overview of different DT platforms that can be used in EV applications. A deductive comparison between model-based and data-driven DT was performed. EV main systems have been discussed regarding the usable DT platform. DT platforms used in the EV industry were addressed. Finally, the review showed the superiority of data-driven DTs over model-based DTs due to their ability to handle systems with high complexity.
Top Cited PapersOpen AccessOverview of Digital Twin Platforms for EV Applications
Digital twin (DT) technology has been used in a wide range of applications, including electric vehicles. The DT platform provides a virtual representation or advanced simulation of a physical object in real-time. The implementation of DT on various aspects of EVs has recently transpired in different research studies. Generally, DT can emulate the actual vehicle on the road to predict/optimize its performance and improve vehicle safety. Additionally, DT can be used for the optimization of manufacturing processes, real-time condition monitoring (at all levels and in all powertrain components), energy management optimization, repurposing of the components, and even recycling processes. This paper presents an overview of different DT platforms that can be used in EV applications. A deductive comparison between model-based and data-driven DT was performed. EV main systems have been discussed regarding the usable DT platform. DT platforms used in the EV industry were addressed. Finally, the review showed the superiority of data-driven DTs over model-based DTs due to their ability to handle systems with high complexity.
- Top Cited PapersOpen Access
- 6 January 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (2) , 601
Overview on Digital Twin for Autonomous Electrical Vehicles Propulsion Drive System
The significant progress in the electric automotive industry brought a higher need for new technological innovations. Digital Twin (DT) is one of the hottest trends of the fourth industrial revolution. It allows representing physical assets under various operating conditions in a low-cost and zero-risk environment. DTs are used in many different fields from aerospace to healthcare. However, one of the perspective applications of such technology is the automotive industry. This paper presents an overview of the implementation of DT technology in electric vehicles (EV) propulsion drive systems. A general review of DT technology is supplemented with main applications analysis and comparison between different simulation technologies. Primary attention is given to the adaptation of DT technology for EV propulsion drive systems.
- 6 January 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (2) , 601
Top Cited PapersOpen AccessOverview on Digital Twin for Autonomous Electrical Vehicles Propulsion Drive System
The significant progress in the electric automotive industry brought a higher need for new technological innovations. Digital Twin (DT) is one of the hottest trends of the fourth industrial revolution. It allows representing physical assets under various operating conditions in a low-cost and zero-risk environment. DTs are used in many different fields from aerospace to healthcare. However, one of the perspective applications of such technology is the automotive industry. This paper presents an overview of the implementation of DT technology in electric vehicles (EV) propulsion drive systems. A general review of DT technology is supplemented with main applications analysis and comparison between different simulation technologies. Primary attention is given to the adaptation of DT technology for EV propulsion drive systems.