Deepa Choudhry
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Deepa Choudhry has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Chin Li Cheung
Department of Chemistry, University of Nebraska-Lincoln, Lincoln, USA
4 shared publications - Avinash Kumar Both
Department of Chemistry University of Nebraska‐Lincoln Lincoln Nebraska USA
2 shared publications Dan Stasko
Department of Chemistry, Missouri Western State University, St. Joseph, USA
1 shared publicationKaitlynn Derr
Department of Chemistry, Missouri Western State University, St. Joseph, USA
1 shared publication- Matthew R. Winburn
Department of Chemistry, University of Nebraska-Lincoln, Lincoln, Nebraska, USA
1 shared publication Ricardo J. Chimentão
Departamento de Fisicoquímica Facultad de Ciencias Químicas Universidad de Concepción Concepción, Casilla 160-C Chile
1 shared publication
Latest Publications
- Open Access
- 10 November 2024
- Published by Wiley in ChemSusChem
- Vol. 18 (4) , e202400776
Plasma‐Assisted Synthesis of Methanol Through Hydrogenation of Carbon Dioxide With Non‐Noble Metal Mixed Oxide Catalysts
The utilization of carbon dioxide through chemical conversion is a promising approach for the recycling of carbon resources. Despite well‐developed industrial processes for CO 2 hydrogenation to methanol, the effective use of CO 2 as a feedstock remains challenging because of the costly requirements of high temperature and reaction pressure. In this paper, we report the methanol synthesis from CO 2 and hydrogen using a dielectric barrier discharge (DBD) reactor under atmospheric pressure with a nickel‐cerium‐aluminum mixed oxide (Ni/Ce−Al MOx) catalyst. The combined use of plasma and the Ni/Ce−Al MOx catalyst was observed to yield 13.3±0.4 % of methanol, favorably compared to the 2.6±0.5 % yield of the case without catalyst. Microscopy images, selected area electron diffraction patterns, and energy‐dispersive X‐ray analysis confirmed the presence of fluorite‐structured ceria, aluminium, nickel, and nickel oxide particles in the catalyst. The reaction mechanism for the plasma‐assisted hydrogenation of CO 2 was hypothesized to involve a carbide formation pathway due to the presence of carbide confirmed by X‐ray photoelectron spectroscopic characterization.
- 10 November 2024
- Published by Wiley in ChemSusChem
- Vol. 18 (4) , e202400776
Open AccessPlasma‐Assisted Synthesis of Methanol Through Hydrogenation of Carbon Dioxide With Non‐Noble Metal Mixed Oxide Catalysts
The utilization of carbon dioxide through chemical conversion is a promising approach for the recycling of carbon resources. Despite well‐developed industrial processes for CO 2 hydrogenation to methanol, the effective use of CO 2 as a feedstock remains challenging because of the costly requirements of high temperature and reaction pressure. In this paper, we report the methanol synthesis from CO 2 and hydrogen using a dielectric barrier discharge (DBD) reactor under atmospheric pressure with a nickel‐cerium‐aluminum mixed oxide (Ni/Ce−Al MOx) catalyst. The combined use of plasma and the Ni/Ce−Al MOx catalyst was observed to yield 13.3±0.4 % of methanol, favorably compared to the 2.6±0.5 % yield of the case without catalyst. Microscopy images, selected area electron diffraction patterns, and energy‐dispersive X‐ray analysis confirmed the presence of fluorite‐structured ceria, aluminium, nickel, and nickel oxide particles in the catalyst. The reaction mechanism for the plasma‐assisted hydrogenation of CO 2 was hypothesized to involve a carbide formation pathway due to the presence of carbide confirmed by X‐ray photoelectron spectroscopic characterization.
- 23 February 2023
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 47 (11) , 5488-5497
Eco-friendly fabrication of coco coir composites for hydroponic cultivation: a green chemistry approach
In this study, we report an eco-friendly biocomposite fabrication process for valorizing coconut fibers (coco coir) by transforming them into multi-purpose biocomposites using a pectin-based one-pot aqueous process. In our green approach, we used high methoxyl pectin (degree of methoxylation: 74%) as a crosslinker for binding lignin present in coco coir under basic conditions via the transesterification reaction. The fabrication process was performed at a moderate reaction temperature (70 °C) with water as the only solvent. We conducted statistical analysis to determine the impact of different mass ratios of pectin to coco coir (1 : 5, 2 : 5, 3 : 5, 4 : 5, and 5 : 5) on the mechanical compressive strength and bulk density of the as-fabricated coco coir composite materials. As this mass ratio increased from 1 : 5 to 5 : 5, the compressive strength of the coco coir composites increased by 3 times and the bulk density increased by ca. 1.3 times. The measurements of electrical conductivity, water retention capacity, carbon-to-nitrogen ratio (C/N), and substrate acidity (pH) of these coco coir biocomposites revealed the applicability of these biocomposites as suitable growth substrates for hydroponic cultivation. These biocomposite substrates were applied to grow Daikon radish in a hydroponic system for a 30-day study to demonstrate their potential for hydroponic cultivation.
- 23 February 2023
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 47 (11) , 5488-5497
Eco-friendly fabrication of coco coir composites for hydroponic cultivation: a green chemistry approach
In this study, we report an eco-friendly biocomposite fabrication process for valorizing coconut fibers (coco coir) by transforming them into multi-purpose biocomposites using a pectin-based one-pot aqueous process. In our green approach, we used high methoxyl pectin (degree of methoxylation: 74%) as a crosslinker for binding lignin present in coco coir under basic conditions via the transesterification reaction. The fabrication process was performed at a moderate reaction temperature (70 °C) with water as the only solvent. We conducted statistical analysis to determine the impact of different mass ratios of pectin to coco coir (1 : 5, 2 : 5, 3 : 5, 4 : 5, and 5 : 5) on the mechanical compressive strength and bulk density of the as-fabricated coco coir composite materials. As this mass ratio increased from 1 : 5 to 5 : 5, the compressive strength of the coco coir composites increased by 3 times and the bulk density increased by ca. 1.3 times. The measurements of electrical conductivity, water retention capacity, carbon-to-nitrogen ratio (C/N), and substrate acidity (pH) of these coco coir biocomposites revealed the applicability of these biocomposites as suitable growth substrates for hydroponic cultivation. These biocomposite substrates were applied to grow Daikon radish in a hydroponic system for a 30-day study to demonstrate their potential for hydroponic cultivation.
- 3 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (10)
Valorization of hemp fibers into biocomposites via one‐step pectin‐based green fabrication process
In this paper, an environmentally friendly fabrication process was reported to valorize hemp fibers into biocomposites through a pectin‐based crosslinking reaction. In this water‐based chemical approach, the hemp fibers were crosslinked via a transesterification process between pectin and lignin present in hemp fibers to produce hemp fiber composites in a one‐step process. Our green process was advantageous over conventional processes that rely on the use of petroleum‐based organic solvents and high reaction temperatures because water was used as the reaction solvent with a mild reaction temperature (70°C). Additionally, to further optimize this biocomposite fabrication process, one‐factor analysis of variance study was carried out for investigating the main and interaction effects of the mass ratios of pectin to hemp fiber (1:5, 2:5, 3:5, 4:5, and 5:5) on the compressive strength and bulk density of the hemp fiber composite materials. In addition, the fabrication process was explored at different pH values to probe its versatility. The compressive strength of the as‐synthesized hemp fiber composite materials was observed to be dependent on the pH of the reaction conditions, indirectly confirming the formation of ester bonds between pectin and the lignin of hemp fibers via transesterification.
- 3 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (10)
Valorization of hemp fibers into biocomposites via one‐step pectin‐based green fabrication process
In this paper, an environmentally friendly fabrication process was reported to valorize hemp fibers into biocomposites through a pectin‐based crosslinking reaction. In this water‐based chemical approach, the hemp fibers were crosslinked via a transesterification process between pectin and lignin present in hemp fibers to produce hemp fiber composites in a one‐step process. Our green process was advantageous over conventional processes that rely on the use of petroleum‐based organic solvents and high reaction temperatures because water was used as the reaction solvent with a mild reaction temperature (70°C). Additionally, to further optimize this biocomposite fabrication process, one‐factor analysis of variance study was carried out for investigating the main and interaction effects of the mass ratios of pectin to hemp fiber (1:5, 2:5, 3:5, 4:5, and 5:5) on the compressive strength and bulk density of the hemp fiber composite materials. In addition, the fabrication process was explored at different pH values to probe its versatility. The compressive strength of the as‐synthesized hemp fiber composite materials was observed to be dependent on the pH of the reaction conditions, indirectly confirming the formation of ester bonds between pectin and the lignin of hemp fibers via transesterification.
- Open Access
- 29 May 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (35) , 20515-20520
Mechanistic insights into the acetate-accelerated synthesis of crystalline ceria nanoparticles
Recent increasing uses of ceria in research and industrial applications have fostered continuing developments of efficient routes to synthesize the material. Here we report our investigation of the effects and the mechanistic roles of lithium acetate to accelerate the growth of crystalline ceria nanoparticles in ozone-mediated synthesis. By increasing the mole ratio of the acetate to cerium nitrate in the reactions, the reaction yields of ceria nanoparticles were observed to increase from ca. 10% to up to over 90% by cerium content in 30 min reactions. Microscopy images and Raman spectra of the as-synthesized nanoparticles revealed that increasing the acetate additions led to a decrease in average particle size and size range but an increase in crystallinity. Through analyzing the organic by-products in the reaction mixtures, the acetate was inferred to base-catalyze the formation of acetals and cerium complexes and accelerate the formation of Ce–O–Ce bonds and hence the growth of ceria nanoparticles through alcohol-like condensation reactions.
- 29 May 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (35) , 20515-20520
Open AccessMechanistic insights into the acetate-accelerated synthesis of crystalline ceria nanoparticles
Recent increasing uses of ceria in research and industrial applications have fostered continuing developments of efficient routes to synthesize the material. Here we report our investigation of the effects and the mechanistic roles of lithium acetate to accelerate the growth of crystalline ceria nanoparticles in ozone-mediated synthesis. By increasing the mole ratio of the acetate to cerium nitrate in the reactions, the reaction yields of ceria nanoparticles were observed to increase from ca. 10% to up to over 90% by cerium content in 30 min reactions. Microscopy images and Raman spectra of the as-synthesized nanoparticles revealed that increasing the acetate additions led to a decrease in average particle size and size range but an increase in crystallinity. Through analyzing the organic by-products in the reaction mixtures, the acetate was inferred to base-catalyze the formation of acetals and cerium complexes and accelerate the formation of Ce–O–Ce bonds and hence the growth of ceria nanoparticles through alcohol-like condensation reactions.